Today's Message Index:
----------------------
1. 04:04 AM - Re: Elevator hinge shim (laflyins)
2. 08:17 AM - Re: Re: Elevator hinge shim (n5pb@AOL.COM)
3. 09:29 AM - Elevator trim motor (Nick Otterback)
4. 12:09 PM - Elevator trim tab hinge (Nick Otterback)
5. 12:36 PM - Trim tab filler strip (Nick Otterback)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Elevator hinge shim |
I don't see any pictures on the last 8 messages.... and yes, I am signed in.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=391590#391590
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Elevator hinge shim |
I got all of em without any issue.
Bear
-----Original Message-----
From: laflyins <laflyins@gmail.com>
Sent: Fri, Jan 4, 2013 7:04 am
Subject: Lightning-List: Re: Elevator hinge shim
I don't see any pictures on the last 8 messages.... and yes, I am signed in
.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=391590#391590
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Elevator trim motor |
Cuttin out the new pre-finished inspection hole. Flanges are 3/8". With the h
ole locations about at the intersection in the corner. Cut on the line excep
t in the corners to leave material for the #6 nutplates and hardware. We opt
ed to make the door out of 0.050 aluminum, however the kit comes with some 3
layer plate to fabricate from.
Nick
Sent from my pocket
<pre><b><font size=2 color="#000000" face="courier new,courier">
</b></font></pre></body></html>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Elevator trim tab hinge |
The aluminum hinge needs to be bonded in with either 24hr aeropoxy/flox mix o
r we used Plexus MA310. Plexus is the structural adhesive used through out t
he plane for construction at custom fiberglass.
Once the hinge is cured the gap between it and the lower skin must be filled
. Use scrap baggage floor material to fabricate a 1/2" wide part that is the
length of the hinge. The material is already the correct thickness at 3/16"
thick. Bomd this part in, leave is slightly recessed in ablut 1/16" or slig
ht more for flox filler later.
Nick
Sent from my pocket
<pre><b><font size=2 color="#000000" face="courier new,courier">
</b></font></pre></body></html>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Trim tab filler strip |
Filler strip bonded in. Note that it is inset by a little more than 1/16" fo
r a epoxy/flox mix later on.
Nick
Sent from my pocket
<pre><b><font size=2 color="#000000" face="courier new,courier">
</b></font></pre></body></html>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|