---------------------------------------------------------- Lightning-List Digest Archive --- Total Messages Posted Fri 01/04/13: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:04 AM - Re: Elevator hinge shim (laflyins) 2. 08:17 AM - Re: Re: Elevator hinge shim (n5pb@AOL.COM) 3. 09:29 AM - Elevator trim motor (Nick Otterback) 4. 12:09 PM - Elevator trim tab hinge (Nick Otterback) 5. 12:36 PM - Trim tab filler strip (Nick Otterback) ________________________________ Message 1 _____________________________________ Time: 04:04:06 AM PST US Subject: Lightning-List: Re: Elevator hinge shim From: "laflyins" I don't see any pictures on the last 8 messages.... and yes, I am signed in. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=391590#391590 ________________________________ Message 2 _____________________________________ Time: 08:17:20 AM PST US Subject: Re: Lightning-List: Re: Elevator hinge shim From: n5pb@AOL.COM I got all of em without any issue. Bear -----Original Message----- From: laflyins Sent: Fri, Jan 4, 2013 7:04 am Subject: Lightning-List: Re: Elevator hinge shim I don't see any pictures on the last 8 messages.... and yes, I am signed in .. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=391590#391590 ________________________________ Message 3 _____________________________________ Time: 09:29:03 AM PST US Subject: Lightning-List: Elevator trim motor From: Nick Otterback Cuttin out the new pre-finished inspection hole. Flanges are 3/8". With the h ole locations about at the intersection in the corner. Cut on the line excep t in the corners to leave material for the #6 nutplates and hardware. We opt ed to make the door out of 0.050 aluminum, however the kit comes with some 3 layer plate to fabricate from. Nick Sent from my pocket
________________________________ Message 4 _____________________________________ Time: 12:09:54 PM PST US Subject: Lightning-List: Elevator trim tab hinge From: Nick Otterback The aluminum hinge needs to be bonded in with either 24hr aeropoxy/flox mix o r we used Plexus MA310. Plexus is the structural adhesive used through out t he plane for construction at custom fiberglass. Once the hinge is cured the gap between it and the lower skin must be filled . Use scrap baggage floor material to fabricate a 1/2" wide part that is the length of the hinge. The material is already the correct thickness at 3/16" thick. Bomd this part in, leave is slightly recessed in ablut 1/16" or slig ht more for flox filler later. Nick Sent from my pocket
________________________________ Message 5 _____________________________________ Time: 12:36:13 PM PST US Subject: Lightning-List: Trim tab filler strip From: Nick Otterback Filler strip bonded in. Note that it is inset by a little more than 1/16" fo r a epoxy/flox mix later on. Nick Sent from my pocket
------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message lightning-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Lightning-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/lightning-list Browse Digests http://www.matronics.com/digest/lightning-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.