Today's Message Index:
----------------------
1. 12:51 AM - Re: Hose question.... (Chris Byrne)
2. 01:39 AM - Re: Hose question.... (Deene Ogden)
3. 04:44 AM - Re: Hose question.... (Gary Casey)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Hose question.... |
The 2 lines I got with my engine were fuel lines.
1. Engine driven fuel pump to Precision Injection body.
2. Injection body to injector spider.
If yours is injected this is what they will be. Sounds like the spider
is on top of the engine, that will be the 31 inch one.
Chris Byrne
Sydney
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Hose question.... |
Firesleeved -6's are usually fuel hoses. You didn't specify which engine
you have...but if its injected, I would suspect the shorter hose is for
gascolator to engine fuel pump and the longer is fuel pump to servo.
Also, on 360's, you usually see -8's on the oil cooler lines, sometimes
sleeved, sometimes not.
YMMV...
And, BTW, the PT part of the tags indicate the pressure test dates...these
hoses are several years old.
Deene
"Ralph E. Capen" <recapen@earthlink.net>
Sent by: owner-lycomingengines-list-server@matronics.com
04/25/2006 08:28 PM
Please respond to
lycomingengines-list@matronics.com
To
"lycoming engine list" <lycomingengines-list@matronics.com>
cc
Subject
LycomingEngines-List: Hose question....
Folks,
I found a couple of hoses that came with my engine from Aerosport power.
They're both firesleeved -6 hoses with steel female NA-6 fittings on each
end.
the only difference in the two hoses is the length 19" / 31" and the
markings on the etched SS tags
>From what I can see:
111F417-6S-0180
CDIQ00
Rubber PT-9-26-02
vs
111F417-6S-0300
CM36424
PT 8/11/03
They're both marked TSO C53a type C / TSO C75 type I APF
What are these for? What can I use them for? Fuel lines????
Thanks,
Ralph Capen
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Hose question.... |
I'll bet they are fuel lines. One is for the fuel pump to the fuel
servo and the other is from the gascolator to the fuel pump. I can't
think of anything else they could be. For the line from the servo to
the distributor a -4 is typically used. A -8 is typically used for
the oil cooler.
Gary Casey
>
> Folks,
> I found a couple of hoses that came with my engine from Aerosport
> power.
>
> They're both firesleeved -6 hoses with steel female NA-6 fittings
> on each end.
>
> the only difference in the two hoses is the length 19" / 31" and
> the markings on
> the etched SS tags
>
> What are these for? What can I use them for? Fuel lines????
>
> Thanks,
> Ralph Capen
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|