---------------------------------------------------------- LycomingEngines-List Digest Archive --- Total Messages Posted Fri 12/18/15: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:40 PM - Lycoming O-360 Fuel Flow Rate (Matt Dralle) 2. 03:43 PM - Re: Lycoming O-360 Fuel Flow Rate (Ed Gilroy) 3. 06:24 PM - Re: Lycoming O-360 Fuel Flow Rate (Deems Herring) ________________________________ Message 1 _____________________________________ Time: 02:40:43 PM PST US From: Matt Dralle Subject: LycomingEngines-List: Lycoming O-360 Fuel Flow Rate I'm still chasing down this weird problem with low fuel flow rates on the RV-6. I've replaced the mechanical fuel pump and got a rebuilt 4-5 carburetor, both of which were well over do for replacement/overhaul anyway. I haven't put the cowling back on yet, but I did a static run up to about 2350-2400 and am seeing about 9gph, which seems low to me? I pulled the fuel line off the carburetor and turned the electric fuel pump on and saw about 21 GPH flow. Is that considered "normal" or too low? Thanks for the feedback, Matt - Matt Dralle RV-8 #82880 N998RV "Ruby Vixen" http://www.mattsrv8.com - Matt's Complete RV-8 Construction Log http://www.mattsrv8.com/Mishap - Landing Mishap Rebuild Log http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel Status: 210+ Hours TTSN - Version 2.0 Now Flying! RV-6 #20916 N360EM "The Flyer" http://www.mattsrv6.com - Matt's RV-6 Revitalization Log Status: 300+ Hours - Full Flyer Mode! Matt's Livermore Airport Live ATC Stream! Check out the live ATC stream directly from my hangar at the Livermore Airport. Includes both Tower and Ground transmissions. Archives too! For entertainment purposes only. http://klvk.matronics.com ________________________________ Message 2 _____________________________________ Time: 03:43:24 PM PST US Subject: Re: LycomingEngines-List: Lycoming O-360 Fuel Flow Rate From: Ed Gilroy You didn't say what your normal static RPM is for the engine/prop combination you have but: Are you sure your mixture control is going full rich when firewalled? Push in full rich, disconnect from mixture lever and see if there is more travel left. There is a mixture stop adjustment/assembly/parts on M/S family carbs. "IF" it still has travel left, it is working as rigged, just not as you would like. Lycoming publishes expected fuel flow in the engine operations manual for your particular model, but it seems if that 2400 RPM is full throttle/Full mixture on your O-360/prop combo, it is low, very low. Something more like 76 lbs/hour at best power mixture which is like 12.5 gals/hour. If you really are only using 9 gph @ 2400 you are making like 110 BHP instead of 170+. I wouldn't try taking off like that. On Fri, Dec 18, 2015 at 5:38 PM, Matt Dralle wrote: > dralle@matronics.com> > > > I'm still chasing down this weird problem with low fuel flow rates on the > RV-6. I've replaced the mechanical fuel pump and got a rebuilt 4-5 > carburetor, both of which were well over do for replacement/overhaul > anyway. I haven't put the cowling back on yet, but I did a static run up > to about 2350-2400 and am seeing about 9gph, which seems low to me? > > I pulled the fuel line off the carburetor and turned the electric fuel > pump on and saw about 21 GPH flow. Is that considered "normal" or too low? > > Thanks for the feedback, > > Matt > > - > Matt Dralle > > RV-8 #82880 N998RV "Ruby Vixen" > http://www.mattsrv8.com - Matt's Complete RV-8 Construction Log > http://www.mattsrv8.com/Mishap - Landing Mishap Rebuild Log > http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel > Status: 210+ Hours TTSN - Version 2.0 Now Flying! > > RV-6 #20916 N360EM "The Flyer" > http://www.mattsrv6.com - Matt's RV-6 Revitalization Log > Status: 300+ Hours - Full Flyer Mode! > > Matt's Livermore Airport Live ATC Stream! > Check out the live ATC stream directly from my hangar at the Livermore > Airport. Includes both Tower and Ground transmissions. Archives too! > For entertainment purposes only. http://klvk.matronics.com > > ________________________________ Message 3 _____________________________________ Time: 06:24:43 PM PST US From: Deems Herring Subject: RE: LycomingEngines-List: Lycoming O-360 Fuel Flow Rate You didn't say what manifold pressure or density altitude was but for sea l evel to 3000ft at WOT 2400 rpm a 180 hp 360 should make about 130-140 Hp an d fuel flow is roughly 0.075 - 0.08 gph per Hp. FAA regulations (23.955) re quire 125% of 100% takeoff power fuel flow. 180 Hp * 0.08 gph = 24.4. 14. 4 * 1.25 = 18 gph so your fuel flow sounds sufficient. The fuel flow curves for Lycoming 180 Hp OI-360 shows 135 Hp is about 10.6 gph give or take depending on mixture. Deems Herring > Date: Fri=2C 18 Dec 2015 14:38:37 -0800 > > > I'm still chasing down this weird problem with low fuel flow rates on the RV-6. I've replaced the mechanical fuel pump and got a rebuilt 4-5 carbur etor=2C both of which were well over do for replacement/overhaul anyway. I haven't put the cowling back on yet=2C but I did a static run up to about 2350-2400 and am seeing about 9gph=2C which seems low to me? > > I pulled the fuel line off the carburetor and turned the electric fuel pu mp on and saw about 21 GPH flow. Is that considered "normal" or too low? ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message lycomingengines-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/LycomingEngines-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/lycomingengines-list Browse Digests http://www.matronics.com/digest/lycomingengines-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.