Today's Message Index:
----------------------
1. 02:53 AM - sensors & probes (loray@compuserve.com)
2. 12:20 PM - Re: Reversing propeller (HBaker)
3. 03:11 PM - Re: Hoses (HBaker)
4. 06:26 PM - Re: Re: Hoses (B-L Pollock)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | sensors & probes |
I've ordered an I-K Technologies' AIM-3000 engine monitor for an
M-14PF, and some questions have come up about the sensors and probes. I'm
hoping someone here can help.
Regarding the RPM sensor, Ralph at I-K Tech writes: "We will provide
a VDO sensor with a 1/8-27 NPT thread." Does this sound right?
He's also asking me what size oil temp probe I want. Since we'll be
converting to western hoses and AN fittings, I assume that any temp probe
that can fit a AN Tee fitting would work. If someone has already done this
and knows what works well, I'd be appreciative for some guidance.
Thanks,
Loray Greiner
--------------------------------------------------------------------
mail2web LIVE Free email based on Microsoft Exchange technology -
http://link.mail2web.com/LIVE
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Reversing propeller |
Hi
What Prop are you going with, is it two blade or three blade?
Henry
Moose #294
--------
Currently building a Murphy Moose - any help would be appreciated.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=227170#227170
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thanks Bill
So #12 is the right size of fittings, did you go with aluminum fittings, and did
you go with fittings that you make yourself? And the #4 line , is it for the
clean kit that uses the scavange pump, and is that all that it hooks up to?
Henry
Moose 294
--------
Currently building a Murphy Moose - any help would be appreciated.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=227215#227215
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Henry, I use three 90 aluminum fittings and the rest straight and yes its
better to custom make yourself with caution of not to kink the steel braided
hose in curves.I only used steel bulkhead fittings for fuel lines through
the firewall which my inspector wanted .The scavenging system goes from the
front nose of the engine to the scavening pump and the to the external oil
tank.Hope that helps.
Bill
Moose 244
----- Original Message -----
From: "HBaker" <henry.baker@nf.sympatico.ca>
Sent: Tuesday, January 27, 2009 6:07 PM
Subject: M14PEngines-List: Re: Hoses
> <henry.baker@nf.sympatico.ca>
>
> Thanks Bill
>
> So #12 is the right size of fittings, did you go with aluminum fittings,
> and did you go with fittings that you make yourself? And the #4 line , is
> it for the clean kit that uses the scavange pump, and is that all that it
> hooks up to?
>
> Henry
>
> Moose 294
>
> --------
> Currently building a Murphy Moose - any help would be appreciated.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=227215#227215
>
>
--------------------------------------------------------------------------------
Checked by AVG - http://www.avg.com
7:26 AM
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|