---------------------------------------------------------- M14PEngines-List Digest Archive --- Total Messages Posted Wed 01/13/10: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:55 AM - Re: Prop Flange (HBaker) 2. 02:57 PM - Re: Re: Prop Flange (Darin Bishop) 3. 05:19 PM - Re: Prop Flange (HBaker) 4. 07:24 PM - Prop Governor (HBaker) ________________________________ Message 1 _____________________________________ Time: 07:55:47 AM PST US Subject: M14PEngines-List: Re: Prop Flange From: "HBaker" Hi Guys I am having trouble getting a ratchet torque wrench to fit the prop flange bolts, I have tried a 19 mm 'crows foot ' because I wanted to torque it, and that doesn't work either any ideas????? Henry Moose 294 -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=281281#281281 ________________________________ Message 2 _____________________________________ Time: 02:57:46 PM PST US From: "Darin Bishop" Subject: Re: M14PEngines-List: Re: Prop Flange Can you weld a socket onto a wrench, put a torque wrench on the socket end? Of course you'll have to measure the extension and do the math to get the torque multiplication figured out and lower torque reading to use. Attached is a wrench I used to torque the cylinder bolts on my Honda CR250 motocross bike. Darin Bishop ________________________________ Message 3 _____________________________________ Time: 05:19:12 PM PST US Subject: M14PEngines-List: Re: Prop Flange From: "HBaker" I guess I'll have to weld it on a open end wrench, it seems to be the only thing that fits it , but the math may be a problem? -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=281364#281364 ________________________________ Message 4 _____________________________________ Time: 07:24:45 PM PST US Subject: M14PEngines-List: Prop Governor From: "HBaker" Hi guys Question for today Ha Ha . How do you set up the prop governor ?? I have a push pull cable hooked to it , but I am not sure if I have enough throw on it , and which way is full coarse , one way seems to have a full stop, the other direction seems to be kind of springy , how do I determine if It is at full through either way?? Henry Moose 294 -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=281381#281381 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message m14pengines-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/M14PEngines-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/m14pengines-list Browse Digests http://www.matronics.com/digest/m14pengines-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.