---------------------------------------------------------- M14PEngines-List Digest Archive --- Total Messages Posted Sun 05/19/13: 11 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 10:44 AM - Oil (HBaker) 2. 11:21 AM - Re: Oil (tedwaltman) 3. 12:33 PM - Re: Oil (HBaker) 4. 03:45 PM - Oil temp probe (HBaker) 5. 03:56 PM - Re: Oil temp probe (tedwaltman) 6. 04:02 PM - Re: Oil temp probe (HBaker) 7. 04:30 PM - Fuel flow (HBaker) 8. 04:45 PM - Fuel system (HBaker) 9. 05:03 PM - Re: Fuel flow (Ben) 10. 05:17 PM - Re: Fuel flow (HBaker) 11. 05:30 PM - Re: Re: Fuel flow (Ben) ________________________________ Message 1 _____________________________________ Time: 10:44:26 AM PST US Subject: M14PEngines-List: Oil From: "HBaker" Can anyone tell me where the thermostat on the oil cooler goes inlet or outlet?? Thanks Henry -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400950#400950 ________________________________ Message 2 _____________________________________ Time: 11:21:50 AM PST US Subject: M14PEngines-List: Re: Oil From: "tedwaltman" Ideally have 2 measures, both inlet & outlet. But specs assume inlet. I see generally 20-C diff between the two. Ted Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400952#400952 ________________________________ Message 3 _____________________________________ Time: 12:33:09 PM PST US Subject: M14PEngines-List: Re: Oil From: "HBaker" Thanks Ted Maybe that's the problem with my low oil temp. Thanks -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400960#400960 ________________________________ Message 4 _____________________________________ Time: 03:45:23 PM PST US Subject: M14PEngines-List: Oil temp probe From: "HBaker" I have installed my oil temp on the bottom of my oil reservoir tank , near where the oil runs out, is this appropriate . Henry -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400964#400964 ________________________________ Message 5 _____________________________________ Time: 03:56:22 PM PST US Subject: M14PEngines-List: Re: Oil temp probe From: "tedwaltman" That is where quite a few people put it. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400965#400965 ________________________________ Message 6 _____________________________________ Time: 04:02:29 PM PST US Subject: M14PEngines-List: Re: Oil temp probe From: "HBaker" Thank you Ted -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400966#400966 ________________________________ Message 7 _____________________________________ Time: 04:30:39 PM PST US Subject: M14PEngines-List: Fuel flow From: "HBaker" I am redoing my fuel flow test , because I am not getting 2900 on my static run up , or even rolling down the runway , at 37 GPH divided by 60 seconds. should I have 0.61 gallons per second?? Does this sound right? Henry [/quote] -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400968#400968 ________________________________ Message 8 _____________________________________ Time: 04:45:52 PM PST US Subject: M14PEngines-List: Fuel system From: "HBaker" This is a picture of the fuel setup in the my moose does anyone have any suggestions? The red block is the fuel flow sending unit. All the lines are 3/8 and the gasolator is before that. -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400969#400969 Attachments: http://forums.matronics.com//files/image_485.jpg ________________________________ Message 9 _____________________________________ Time: 05:03:25 PM PST US From: "Ben" Subject: Re: M14PEngines-List: Fuel flow You are burning 37 gallons an hour.... not a minute...... do not archive Ben Haas N801BH www.haaspowerair.com ---------- Original Message ---------- From: "HBaker" Subject: M14PEngines-List: Fuel flow m> I am redoing my fuel flow test , because I am not getting 2900 on my sta tic run up , or even rolling down the runway , at 37 GPH divided by 60 seconds. should I have 0.61 gallons per second?? Does this sound right? Henry [/quote] -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400968#400968 ======================== =========== ======================== =========== ======================== =========== ======================== =========== ____________________________________________________________ Transformation of America? Stocks soar--but some wealthy citizens are preparing for huge changes http://thirdpartyoffers.netzero.net/TGL3241/5199683bd58ea683b3597st04duc ________________________________ Message 10 ____________________________________ Time: 05:17:51 PM PST US Subject: M14PEngines-List: Re: Fuel flow From: "HBaker" HBaker wrote: > I am redoing my fuel flow test , because I am not getting 2900 on my static run up , or even rolling down the runway , at 37 GPH divided by 60 seconds. should I have 0.61 gallons per Minute ??Does this sound right? > > Henry -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400971#400971 ________________________________ Message 11 ____________________________________ Time: 05:30:23 PM PST US From: "Ben" Subject: Re: M14PEngines-List: Re: Fuel flow Yup....... a little more then 1/2 gallon a minute sounds about right... .. do not archive Ben Haas N801BH www.haaspowerair.com ---------- Original Message ---------- From: "HBaker" Subject: M14PEngines-List: Re: Fuel flow m> HBaker wrote: > I am redoing my fuel flow test , because I am not getting 2900 on my s tatic run up , or even rolling down the runway , at 37 GPH divided by 6 0 seconds. should I have 0.61 gallons per Minute ??Does this sound right ? > > Henry -------- Currently building a Murphy Moose - any help would be appreciated. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=400971#400971 ======================== =========== ======================== =========== ======================== =========== ======================== =========== ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now. http://www.netzero.net/?refcd=NZINTISP0512T4GOUT1 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message m14pengines-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/M14PEngines-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/m14pengines-list Browse Digests http://www.matronics.com/digest/m14pengines-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.