Today's Message Index:
----------------------
1. 12:15 PM - horizontal stab (HBaker)
2. 05:10 PM - Re: horizontal stab (Jeff Micheal)
3. 06:42 PM - Re: horizontal stab (HBaker)
4. 11:29 PM - Re: Re: horizontal stab (Jeff Micheal)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Hi Guys
Getting ready for paint, and trying to figure out if I can install the horizontal
stab and elevator after riveting the fiber glass fairing , it doesn't look
like it . Any suggestions on this? It will be hard to paint separately .
Henry
--------
Currently building a Murphy Moose - any help would be appreciated.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=292097#292097
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: horizontal stab |
Henry,
Cut the fiberglass fairing so the horizontal stab and vertical stab pieces
are separate for installation. You could rivet the vertical stab fairing in
place, but I would use screws to install the horizontal stab fairing pieces
in place; you'll have to remove these pieces at a later date for inspection
anyways. Doing it this way will allow you to install elevator and stab.
Cheers,
Jeff
On Sun, Mar 28, 2010 at 12:15 PM, HBaker <henry.baker@nf.sympatico.ca>wrote:
> henry.baker@nf.sympatico.ca>
>
> Hi Guys
>
> Getting ready for paint, and trying to figure out if I can install the
> horizontal stab and elevator after riveting the fiber glass fairing , it
> doesn't look like it . Any suggestions on this? It will be hard to paint
> separately .
>
> Henry
>
> --------
> Currently building a Murphy Moose - any help would be appreciated.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=292097#292097
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: horizontal stab |
Not real clear on what you are saying, do I put screws in the whole fairing , Or
cut the fairing some where???
--------
Currently building a Murphy Moose - any help would be appreciated.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=292154#292154
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: horizontal stab |
Henry,
You have to cut the fairings. I'll see if I can get a picture to you
tomorrow or within a day or two.
cheers,
Jeff
On Sun, Mar 28, 2010 at 6:41 PM, HBaker <henry.baker@nf.sympatico.ca> wrote:
> henry.baker@nf.sympatico.ca>
>
> Not real clear on what you are saying, do I put screws in the whole fairing
> , Or cut the fairing some where???
>
> --------
> Currently building a Murphy Moose - any help would be appreciated.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=292154#292154
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|