MurphyMoose-List Digest Archive

Fri 11/25/11


Total Messages Posted: 2



Today's Message Index:
----------------------
 
     0. 12:24 AM - Just A Few More Days To Make Your List Contribution... (Matt Dralle)
     1. 12:33 PM - SR-2500 Wing Control Tube Question (Jerald Folkerts)
 
 
 


Message 0


  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:24:21 AM PST US
    From: Matt Dralle <dralle@matronics.com>
    Subject: Just A Few More Days To Make Your List Contribution...
    There is less than a week left in this year's List Fund Raiser and only a few short days to grab one of the great Contribution Gifts available this year. Support is still significantly lagging behind last year at this point but hopefully it will pick up here towards the end. Please remember that it is solely the Contributions of List members that keeps the Lists up and running as there is no commercialism or advertising on the Matronics Lists and Forums. The List Contribution web site is secure, fast, and easy and you can use a credit card, Paypal: http://www.matronics.com/contribution Or, drop a personal check in the mail to: Matt Dralle / Matronics 581 Jeannie Way Livermore CA 94550 I want to thank everyone that has already made a generous contribution to support the Lists! Thank you! Matt Dralle Matronics EMail List and Forum Administrator


    Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:33:21 PM PST US
    From: "Jerald Folkerts" <jfolkerts1@gmail.com>
    Subject: SR-2500 Wing Control Tube Question
    Today, I've been fitting the torque tube in my right wing, just in front of the main spar. I built the torque tube bracket per the manual, but in installing the torque tube assembly to the bracket, the manual calls for an AN4-13A bolt, an AN960-418 washer, then an AIL-26 bushing (inner) in the AIL-27 brass bushing that is fitted to the bracket. Then an AN970-4 Penny Washer and another AN960-418 washer between the bushings and the torque tube. OK, the question, the AIL-26 bushing is 5/32" longer than the AIL-27 bushing it fits in. That introduces right to left movement in the torque tube. Should I trim the AIL-26 busing to fit? In addition, prior to final assembly, should I lubricate the bushing with some grease or something? Thanks, Jerry Folkerts SR #093 www.mykitlog.com/jfolkerts/




    Other Matronics Email List Services

  • Post A New Message
  •   murphymoose-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/MurphyMoose-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/murphymoose-list
  • Browse MurphyMoose-List Digests
  •   http://www.matronics.com/digest/murphymoose-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --