Today's Message Index:
----------------------
1. 09:40 AM - Re: aluminum parts (Barry Davis)
2. 12:48 PM - Model A Engine Ignition (Prange Larry J PSNS)
3. 02:32 PM - SNF (Richard Navratil)
4. 11:08 PM - Re: aluminum parts (dave rowe)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: aluminum parts |
I would like to see the pictures. You could send them off-group at bed@mindspring.com
Thanks Barry
----- Original Message -----
From: Les Schubert
To: pietenpol-list@matronics.com
Sent: Tuesday, April 13, 2004 10:35 AM
Subject: Pietenpol-List: aluminum parts
From: dave rowe <rowed044@shaw.ca>
Subject: Re: Pietenpol-List: 4130 Question
--> Pietenpol-List message posted by: dave rowe <rowed044@shaw.ca>
The plans I have say the hinges etc have been replaced by cast
aluminum. I designed and built bolt-together 6061 T-6 aluminum pieces
that far exceed the min strength required, and take a couple of evenings
to make out of flat and angle stock. Haven't done up proper set of
drawings, but have plenty of digital photos if you'd like.
Dave I would really like to se some pictures.
Thanks
Les
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Model A Engine Ignition |
Old-X-N-Score: scored 0
--> Pietenpol-List message posted by: Prange Larry J PSNS <prangel@psns.navy.mil>
Dear 'A' Ford Engine Gurus,
On my ('31) Ford I am currently using a single magneto per The Plans.
However, I would like to add a second ignition source (magneto or battery)
and wire both systems to one set of plugs. I have the engine's (former)
starter location taken up by an oil filter, so that type of conversion is
out. I guess that I will be adding something in the original distributor
hole or . . . . ? Ideas Please! I am looking for some sage advice about
what would be some good equipment choices and maybe even sources for same.
Are there any known problems with using two ignition systems with one set of
plugs?
Thanks,
Larry Prange
NX1929A
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I made it back to St. Paul late last night with my SNF built wings. Thanks to
all who helped put them together.
Now it's time to get out and see if the other Piet really will fly.
Dick N.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: aluminum parts |
<006901c426f5$4ece4340$1b02a8c0@WorkGroup>
--> Pietenpol-List message posted by: dave rowe <rowed044@shaw.ca>
Roger that, things are pretty busy at the moment, but I will get them
out by the end of the week. Thanks for the interest!
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|