Today's Message Index:
----------------------
1. 11:27 AM - Re: Need help finding a master cylinder (Richard Navratil)
2. 01:07 PM - Re: Need help finding a master cylinder (srmjem)
3. 02:55 PM - Re: Burl wood for panel (Carl Vought)
4. 05:16 PM - Re: Need help finding a master cylinder (Richard Navratil)
5. 05:29 PM - Re: Need help finding a master cylinder (Bert Conoly)
6. 06:58 PM - Re: Need help finding a master cylinder (John and Phyllis Smoyer)
7. 11:20 PM - burl (Clif Dawson)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Need help finding a master cylinder |
Sam
Here is my brake set up. The brake line goes thru the floor and tees to each caliper.
Works very good, but the caliper is a bit undersized and will only hold
to about 1400 rpm with the A-65.
If you want to see the caliper set up, I can send more detail off line.
Dick N
----- Original Message -----
From: srmjem
To: pietenpol-list@matronics.com
Sent: Sunday, January 16, 2005 8:23 PM
Subject: Re: Pietenpol-List: Need help finding a master cylinder
. With a steerable tailwheel I havent had the need for individual brakes.
Dick,
I'm also going to put a single master cylinder with a hand lever to operate
both brakes in my Piet but haven't figured out how to do it yet. Could
you post a picture of your brake system?
Thanks,
Sam
do not archive
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Need help finding a master cylinder |
Dick,
Thanks for posting the picture of your brake system. I have a master cylinder
with a built in reservoir so I won;t need a separate one. I may place the
handlever on the left side instead of the right as you have yours.
Sam
do not archive
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Burl wood for panel |
----- Original Message -----
From: N321TX@wmconnect.com
To: pietenpol-list@matronics.com
Sent: Saturday, January 15, 2005 1:00 PM
Subject: Pietenpol-List: Burl wood for panel
There's an outfit that goes by the name of CONSTANTINES that I bought some burhl
from to rework the dash of an old Jaguar. I was very satisfied with what I
got...paper thin but sufficient. If you have trouble getting to them with what
little I've given you, contact me off line...You have my email address...Carl
Vought
Can anyone recommend a good source for burl wood for the instrument panel? I
saw a great example of this at Oshkosh last summer and it really made the cockpit
standout.
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Need help finding a master cylinder |
I put mine on the right because the throttle is on the left. Dont want to reach
for one and hit the other.
Dick
----- Original Message -----
From: srmjem
To: pietenpol-list@matronics.com
Sent: Monday, January 17, 2005 2:21 PM
Subject: Re: Pietenpol-List: Need help finding a master cylinder
Dick,
Thanks for posting the picture of your brake system. I have a master
cylinder with a built in reservoir so I won;t need a separate one. I may place
the handlever on the left side instead of the right as you have yours.
Sam
do not archive
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
s=test1; d=earthlink.net;
b=HSRMWfQU1Q+FYLaH2gQSGumory7oOCtJWa8EnDTjrESIQ7MGGVVEy/Fp1eSmRG0O;
Subject: | Re: Need help finding a master cylinder |
John: I used go-cart master cylinders. I added a page to my website- pics on
there.. If you want better pics I can send them to you this weekend.
Bert
http://bconoly.tripod.com/id17.html
----- Original Message -----
From: John and Phyllis Smoyer
To: pietenpol-list@matronics.com
Sent: Saturday, January 15, 2005 8:24 PM
Subject: Pietenpol-List: Need help finding a master cylinder
Can anyone advise me on a good source for a brake master cylinder suitable for
a Piet? Thanks to everyone for the informative postings and images. I really
enjoy this group.
Best Regards,
John Smoyer
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Need help finding a master cylinder |
Bert: thanks very much. I'm a volunteer for an air museum, working on constructing
an Air Camper. I'll review these pics with the boss on Wednesday. We never
thought of go-cart brakes, but it sounds like a great idea. Thanks very
much for your input, and for yourr great web-site.
Your plane sure looks like a beauty. I clicked on the "what's a GN-1" link, but
didn't look like any info came up. So, what is a GN-1, as compared to an Air
Camper, anyway?
Thanks, and best regards,
John Smoyer
----- Original Message -----
From: Bert Conoly
To: pietenpol-list@matronics.com
Sent: Monday, January 17, 2005 7:54 PM
Subject: Re: Pietenpol-List: Need help finding a master cylinder
John: I used go-cart master cylinders. I added a page to my website- pics on
there.. If you want better pics I can send them to you this weekend.
Bert
http://bconoly.tripod.com/id17.html
----- Original Message -----
From: John and Phyllis Smoyer
To: pietenpol-list@matronics.com
Sent: Saturday, January 15, 2005 8:24 PM
Subject: Pietenpol-List: Need help finding a master cylinder
Can anyone advise me on a good source for a brake master cylinder suitable
for a Piet? Thanks to everyone for the informative postings and images. I really
enjoy this group.
Best Regards,
John Smoyer
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
I think I've figured out what my wood is.
It has all the characteristics of the catalpa
that I have used for carving in the past. I've
still got a fair bit left. The reddish veneer
I'm not sure of still.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|