Today's Message Index:
----------------------
 
     1. 06:42 PM - Torch Tips (Glenn Thomas)
     2. 09:45 PM - Re: Re: Elevators (Dick Navratil)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:42:01 PM PST US
Subject: 
Torch Tips
From: 
"Glenn Thomas" <glennthomas@flyingwood.com>
      
      
      Just got the Harris Aviator package (torch Model 15) and it came with 0, 1 & 2
      tips.  Will I need a larger tip to possible do some bending etc?  If so, what
      other sizes come in handy.  Didn't get a cutting torch, is that something you
      use much?  
      
      Only welding I've done was at OshKosh.  Any good non-throwaway projects to practice
      with?  I have a couple in mind but I know a lot of you have probably been
      where I am now and might have some tips that I or others getting started with
      welding might benefit from.
      
      Thanks!
      
      --------
      Glenn Thomas
      N?????
      http://www.flyingwood.com
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=84117#84117
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
09:45:08 PM PST US
From: 
"Dick Navratil" <horzpool@goldengate.net>
Subject: 
Re: Elevators
      
      
      Steve
      When posting this type of thing, it would be helpful to include where you 
      live.  Somebody may well have a local source for you.
      Dick N.
      ----- Original Message ----- 
      From: "Steve Singleton" <slsingleton@cvalley.net>
      Sent: Wednesday, December 27, 2006 9:19 PM
      Subject: Re: Pietenpol-List: Re: Elevators
      
      
      > <slsingleton@cvalley.net>
      >
      > I'll look into the Okume and also see if I can find a Marine supply house. 
      > Worked most of today on the tail and have it all ready to glue togeather 
      > except the rudder and hopefully will get that done tomorrow. I know i'm 
      > just a beginer at this but it's sure neat to see all this layed out and 
      > ready to glue up. Steve S
      > ----- Original Message ----- 
      > From: "Dave and Connie" <dmatt@frontiernet.net>
      > To: <pietenpol-list@matronics.com>; <pietenpol-list@matronics.com>
      > Sent: Wednesday, December 27, 2006 12:12 PM
      > Subject: Re: Pietenpol-List: Re: Elevators
      >
      >
      >> <dmatt@frontiernet.net>
      >>
      >> At 12:12 PM 12/27/2006, Dick Navratil wrote:
      >> One source for Okume is places that cater to stitch and glue boat 
      >> builders.   I purchased from Noah's Marine in Toronto when I built my 
      >> Chesapeake 17 kayak.  Bringing it back into the US was no problem.
      >>
      >
      >
      > 
      
      








Other Matronics Email List Services




Post A New Message
  
pietenpol-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Pietenpol-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/pietenpol-list
Browse Pietenpol-List Digests
  
http://www.matronics.com/digest/pietenpol-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --