Pietenpol-List Digest Archive

Sun 12/23/07


Total Messages Posted: 16



Today's Message Index:
----------------------
 
     1. 05:34 AM - Plans Page Missing? (Glenn Thomas)
     2. 05:39 AM - Re: Center Section Assembly (walt evans)
     3. 06:19 AM - Re: Plans Page Missing? (HelsperSew@aol.com)
     4. 06:55 AM - Re: Plans Page Missing? (Ben Charvet)
     5. 08:46 AM - anyone in the Raleigh/Durham area?? (Gene Rambo)
     6. 11:55 AM - Re: Plans Page Missing? (Glenn Thomas)
     7. 12:00 PM - Re: Center Section Assembly (Jack T. Textor)
     8. 03:14 PM - Re: Center Section Assembly (walt evans)
     9. 03:41 PM - Re: Plans Page Missing? (Ryan Mueller)
    10. 04:30 PM - Re: Plans Page Missing? (gcardinal)
    11. 05:18 PM - Re: anyone in the Raleigh/Durham area?? (pietflyr)
    12. 05:57 PM - Re: Plans Page Missing? (dwilson)
    13. 06:14 PM - Re: Re: Plans Page Missing? (Arden Adamson)
    14. 06:20 PM - Re: Re: Plans Page Missing? (Glenn Thomas)
    15. 08:54 PM - Re: Model A engine (MF)
    16. 09:00 PM - Re: Re: Plans Page Missing? (gcardinal)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:34:08 AM PST US
    Subject: Plans Page Missing?
    From: "Glenn Thomas" <glennthomas@flyingwood.com>
    I was looking through my plans and can't find a page that specs out the straight axel landing gear. I do see it in the flying and glider manual. Is F&G the only place to see dimensions on the straight axel gear? -------- Glenn Thomas N????? http://www.flyingwood.com Read this topic online here: http://forums.matronics.com/viewtopic.php?p=153799#153799


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:39:54 AM PST US
    From: "walt evans" <waltdak@verizon.net>
    Subject: Re: Center Section Assembly
    Jack, I wouldn't cap the ribs with ply. It's not in the plans, and there is no reason for it. There are just too many times where you have to have access thru that area. Just make sure the "root" ribs (outboard on the center section, and the root of the wings) have the extra rib sticks, as per plans, and have the 2" wide (I think) ply on the rib perimiter to stop fabric causing distortion. PS after re reading your email, not sure if the 2" wide is what you mean. Cause you do need that. walt evans NX140DL "No one ever learned anything by talking" Ben Franklin ----- Original Message ----- From: Jack T. Textor To: pietenpol-list@matronics.com Sent: Saturday, December 22, 2007 3:55 PM Subject: Pietenpol-List: Center Section Assembly Hi all, Can anyone share with me the best order of assembling the center section? I have learned it's best not to cap the end ribs with the ply. Wishing everyone the best Holiday! Jack www.textors.com


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:19:49 AM PST US
    From: HelsperSew@aol.com
    Subject: Re: Plans Page Missing?
    Glenn, Yes, the only specs for this are in the F&G manual. Save yourself a whole lot of heartache, and go directly to Chris Tracy's sight Westcoastpiet.com and see his special section on his step-by step procedure he used to construct this SA gear. I struggled through it and wasted MUCH time and energy. Dan Helsper Poplar Grove, IL. **************************************See AOL's top rated recipes (http://food.aol.com/top-rated-recipes?NCID=aoltop00030000000004)


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:55:34 AM PST US
    From: Ben Charvet <bcharvet@bellsouth.net>
    Subject: Re: Plans Page Missing?
    Glenn, My plans are the same way. I have a copy of the F&G pages if you need them. Ben Glenn Thomas wrote: > > I was looking through my plans and can't find a page that specs out the straight axel landing gear. I do see it in the flying and glider manual. Is F&G the only place to see dimensions on the straight axel gear? > > -------- > Glenn Thomas > N????? > http://www.flyingwood.com > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=153799#153799 > > >


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:46:23 AM PST US
    From: "Gene Rambo" <generambo@msn.com>
    Subject: anyone in the Raleigh/Durham area??
    I think I have asked this before, but is anyone in the RDU area? I have a couple of overnights there, Christmas eve and day, and was wondering if there are any projects close by rather than sitting in a hotel room on Christmas. Gene


    Message 6


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:55:04 AM PST US
    From: "Glenn Thomas" <glennthomas@flyingwood.com>
    Subject: Re: Plans Page Missing?
    Thanks a lot guys! I have the F&G and just finished scanning and enlarging all the sections of the drawing into several pages. They're good drawings. I'll also refer to Chris's excellent site as well. I was just wondering how that drawing didn't make it into the larger group of drawings. Merry Christmas! On 12/23/07, Ben Charvet <bcharvet@bellsouth.net> wrote: > > > Glenn, > My plans are the same way. I have a copy of the F&G pages if you need > them. > > Ben > Glenn Thomas wrote: > glennthomas@flyingwood.com> > > > > I was looking through my plans and can't find a page that specs out the > straight axel landing gear. I do see it in the flying and glider > manual. Is F&G the only place to see dimensions on the straight axel gear? > > > > -------- > > Glenn Thomas > > N????? > > http://www.flyingwood.com > > > > > > > > > > Read this topic online here: > > > > http://forums.matronics.com/viewtopic.php?p=153799#153799 > > > > > > > > > > > > > > > > > > > > > > > > > > > > -- Glenn Thomas Storrs, CT http://www.flyingwood.com


    Message 7


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:00:19 PM PST US
    Subject: Center Section Assembly
    From: "Jack T. Textor" <jtextor@thepalmergroup.com>
    Walt, Thanks for the note and pictures, they were helpful. Yes, I was talking about the 2" strip of ply. Is it best to start the assembly by gluing the end ribs to the spars? I assume I need to wait on the lower compression struts until the cabane straps are in place. Also, on the straps, should I drill them to the spars before assembly or align them and drill after everything is put together? So many questions! Thanks! Jack www.textors.com


    Message 8


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 03:14:10 PM PST US
    From: "walt evans" <waltdak@verizon.net>
    Subject: Re: Center Section Assembly
    Jack, Boy, It's been over 6 years since working on that part. I'll let the others jump in on this. In the mean time I'll go over my pics, and put on the old thinking cap. If a light goes on, I'll share it. walt evans NX140DL "No one ever learned anything by talking" Ben Franklin ----- Original Message ----- From: Jack T. Textor To: pietenpol-list@matronics.com Sent: Sunday, December 23, 2007 2:52 PM Subject: RE: Pietenpol-List: Center Section Assembly Walt, Thanks for the note and pictures, they were helpful. Yes, I was talking about the 2" strip of ply. Is it best to start the assembly by gluing the end ribs to the spars? I assume I need to wait on the lower compression struts until the cabane straps are in place. Also, on the straps, should I drill them to the spars before assembly or align them and drill after everything is put together? So many questions! Thanks! Jack www.textors.com


    Message 9


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 03:41:04 PM PST US
    From: Ryan Mueller <rmueller23@yahoo.com>
    Subject: Re: Plans Page Missing?
    Glenn, Don't quote me on this, but if I remember correctly the plans from the Pietenpol family are the 1933 "Improved Plans". Some of the improvements included the redesigned split-axle landing gear, and I think the fuselage was lengthened by an inch or two. There might be other slight changes, but those are the two I recall off the top of my head. So there would have been no omission as far as what you paid for, it's just that the straight axle wood gear had been "superseded" in the plans by the split axle. I hope everyone is enjoying the holidays with their families, and Jess and I wish you all a Merry Christmas and a Happy New Year. Ryan Glenn Thomas <glennthomas@flyingwood.com> wrote: Thanks a lot guys! I have the F&G and just finished scanning and enlarging all the sections of the drawing into several pages. They're good drawings. I'll also refer to Chris's excellent site as well. I was just wondering how that drawing didn't make it into the larger group of drawings. Merry Christmas! Glenn, My plans are the same way. I have a copy of the F&G pages if you need them. Ben Glenn Thomas wrote: > > I was looking through my plans and can't find a page that specs out the straight axel landing gear. I do see it in the flying and glider manual. Is F&G the only place to see dimensions on the straight axel gear? > > -------- > Glenn Thomas > N????? > http://www.flyingwood.com > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=153799#153799 > > -- Glenn Thomas Storrs, CT http://www.flyingwood.com --------------------------------- Never miss a thing. Make Yahoo your homepage.


    Message 10


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:30:46 PM PST US
    From: "gcardinal" <gcardinal@comcast.net>
    Subject: Re: Plans Page Missing?
    The plans that were available through Orrin Hoopman included the Jenny style landing gear. Does anybody know if Mr. Hoopman's heirs still offer those plans for sale? Greg Cardinal ----- Original Message ----- From: Ryan Mueller To: pietenpol-list@matronics.com Sent: Sunday, December 23, 2007 5:40 PM Subject: Re: Pietenpol-List: Plans Page Missing? Glenn, Don't quote me on this, but if I remember correctly the plans from the Pietenpol family are the 1933 "Improved Plans". Some of the improvements included the redesigned split-axle landing gear, and I think the fuselage was lengthened by an inch or two. There might be other slight changes, but those are the two I recall off the top of my head. So there would have been no omission as far as what you paid for, it's just that the straight axle wood gear had been "superseded" in the plans by the split axle. I hope everyone is enjoying the holidays with their families, and Jess and I wish you all a Merry Christmas and a Happy New Year. Ryan Glenn Thomas <glennthomas@flyingwood.com> wrote: Thanks a lot guys! I have the F&G and just finished scanning and enlarging all the sections of the drawing into several pages. They're good drawings. I'll also refer to Chris's excellent site as well. I was just wondering how that drawing didn't make it into the larger group of drawings. Merry Christmas! On 12/23/07, Ben Charvet <bcharvet@bellsouth.net> wrote: <bcharvet@bellsouth.net > Glenn, My plans are the same way. I have a copy of the F&G pages if you need them. Ben Glenn Thomas wrote: glennthomas@flyingwood.com> > > I was looking through my plans and can't find a page that specs out the straight axel landing gear. I do see it in the flying and glider manual. Is F&G the only place to see dimensions on the straight axel gear? > > -------- > Glenn Thomas > N????? > http://www.flyingwood.com > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=153799#153799 > > > > > > > > > > > -- Glenn Thomas Storrs, CT http://www.flyingwood.com


    Message 11


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:18:57 PM PST US
    From: "pietflyr" <pietflyr@bellsouth.net>
    Subject: anyone in the Raleigh/Durham area??
    SGkgR2VuZSwNCg0KSSdtIGluIHRoZSBSRFUgYXJlYSwgYnV0IHVuZm9ydHVuYXRlbHkgd2lsbCBu b3QgYmUgb3ZlciBDaHJpc3RtYXMuICBJJ20gZmx5aW5nIHRvIEJsYWNrc2J1cmcgVkEgdG8gc3Bl bmQgdGltZSB3aXRoIG15IHdpZmUncyBmYW1pbHkgZm9yIENocmlzdG1hcy4gIEhvd2V2ZXIsIGlm IHlvdSBnZXQgZG93biB0byBDb3ggRmllbGQgaW4gQXBleCAoOCBtaWxlcyBTU1cgb2YgUkRVKSB5 b3UgYXJlIHdlbGNvbWUgdG8gc3RvcCBpbiBhbmQgbG9vayBhdCBteSBQaWV0ZW5wb2wuICBJdCdz IGluIHRoZSBicm93biBoYW5nYXIgdGhlcmUuDQoNCkphY2sgUGhpbGxpcHMNCk5YODk5SlANCiAg LS0tLS1PcmlnaW5hbCBNZXNzYWdlLS0tLS0NCiAgRnJvbTogb3duZXItcGlldGVucG9sLWxpc3Qt c2VydmVyQG1hdHJvbmljcy5jb20gW21haWx0bzpvd25lci1waWV0ZW5wb2wtbGlzdC1zZXJ2ZXJA bWF0cm9uaWNzLmNvbV1PbiBCZWhhbGYgT2YgR2VuZSBSYW1ibw0KICBTZW50OiBTdW5kYXksIERl Y2VtYmVyIDIzLCAyMDA3IDg6NDcgQU0NCiAgVG86IHBpZXRlbnBvbC1saXN0QG1hdHJvbmljcy5j b20NCiAgU3ViamVjdDogUGlldGVucG9sLUxpc3Q6IGFueW9uZSBpbiB0aGUgUmFsZWlnaC9EdXJo YW0gYXJlYT8/DQoNCg0KICBJIHRoaW5rIEkgaGF2ZSBhc2tlZCB0aGlzIGJlZm9yZSwgYnV0IGlz IGFueW9uZSBpbiB0aGUgUkRVIGFyZWE/ICBJIGhhdmUgYSBjb3VwbGUgb2Ygb3Zlcm5pZ2h0cyB0 aGVyZSwgQ2hyaXN0bWFzIGV2ZSBhbmQgZGF5LCBhbmQgd2FzIHdvbmRlcmluZyBpZiB0aGVyZSBh cmUgYW55IHByb2plY3RzIGNsb3NlIGJ5IHJhdGhlciB0aGFuIHNpdHRpbmcgaW4gYSBob3RlbCBy b29tIG9uIENocmlzdG1hcy4NCg0KICBHZW5lDQoNCg0KXy09PT09PT09PT09PT09PT09PT09PT09 PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT0NCl8tPQ0KXy09ICAgICAgIC0t IFBsZWFzZSBTdXBwb3J0IFlvdXIgTGlzdHMgVGhpcyBNb250aCAtLQ0KXy09ICAgICAgICAgICAo QW5kIEdldCBTb21lIEFXRVNPTUUgRlJFRSBHaWZ0cyEpDQpfLT0NCl8tPSAgIE5vdmVtYmVyIGlz IHRoZSBBbm51YWwgTGlzdCBGdW5kIFJhaXNlci4gIENsaWNrIG9uDQpfLT0gICB0aGUgQ29udHJp YnV0aW9uIGxpbmsgYmVsb3cgdG8gZmluZCBvdXQgbW9yZSBhYm91dA0KXy09ICAgdGhpcyB5ZWFy J3MgVGVycmlmaWMgRnJlZSBJbmNlbnRpdmUgR2lmdHMhDQpfLT0NCl8tPSAgIExpc3QgQ29udHJp YnV0aW9uIFdlYiBTaXRlOg0KXy09DQpfLT0gICAtLT4gaHR0cDovL3d3dy5tYXRyb25pY3MuY29t L2NvbnRyaWJ1dGlvbg0KXy09DQpfLT0gICBUaGFuayB5b3UgZm9yIHlvdXIgZ2VuZXJvdXMgc3Vw cG9ydCENCl8tPQ0KXy09ICAgICAgICAgICAgICAgICAgICAgICAgICAgICAgLU1hdHQgRHJhbGxl LCBMaXN0IEFkbWluLg0KXy09DQpfLT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09 PT09PT09PT09PT09PT09PT09PT09PT09PQ0KXy09ICAgICAgICAgIC0gVGhlIFBpZXRlbnBvbC1M aXN0IEVtYWlsIEZvcnVtIC0NCl8tPSBVc2UgdGhlIE1hdHJvbmljcyBMaXN0IEZlYXR1cmVzIE5h dmlnYXRvciB0byBicm93c2UNCl8tPSB0aGUgbWFueSBMaXN0IHV0aWxpdGllcyBzdWNoIGFzIExp c3QgVW4vU3Vic2NyaXB0aW9uLA0KXy09IEFyY2hpdmUgU2VhcmNoICYgRG93bmxvYWQsIDctRGF5 IEJyb3dzZSwgQ2hhdCwgRkFRLA0KXy09IFBob3Rvc2hhcmUsIGFuZCBtdWNoIG11Y2ggbW9yZToN Cl8tPSAgIC0tPiBodHRwOi8vd3d3Lm1hdHJvbmljcy5jb20vTmF2aWdhdG9yP1BpZXRlbnBvbC1M aXN0DQpfLT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09 PT09PT09PT09PQ0KXy09ICAgICAgICAgICAgICAgLSBNQVRST05JQ1MgV0VCIEZPUlVNUyAtDQpf LT0gU2FtZSBncmVhdCBjb250ZW50IGFsc28gYXZhaWxhYmxlIHZpYSB0aGUgV2ViIEZvcnVtcyEN Cl8tPSAgIC0tPiBodHRwOi8vZm9ydW1zLm1hdHJvbmljcy5jb20NCl8tPT09PT09PT09PT09PT09 PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09PT09DQoNCg=


    Message 12


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:57:52 PM PST US
    Subject: Re: Plans Page Missing?
    From: "dwilson" <marwilson@charter.net>
    Greg, I spoke with Goldie Hoopman just a couple of weeks ago. She is doing great! A couple of months ago she gave me dozens of drawings that she had stored in her basement. She no longer sells plans and when people inquire she tells them to contact Don Pietenpol in Rochester, MN. However, there is an original drawing of the Jenny style landing gear in the many plan drawings that I obtained from Mrs. Hoopman. I dont think that there would be anything wrong with sending someone a copy if they needed one. The drawing I have is 11 X 17. I may even be able to scan the image and email it as a pdf. Dan Wilson Austin, MN Read this topic online here: http://forums.matronics.com/viewtopic.php?p=153923#153923


    Message 13


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:14:20 PM PST US
    Subject: Re: Plans Page Missing?
    From: "Arden Adamson" <aadamson@wnmdag.org>
    Dan, I've been following the discussions about the Jenny style landing gear. I am building mine as we speak. It would certainly be appreciated if I could somehow obtain a copy of the 11 X 17 drawings. If cost is involved, I'd gladly pay. To all on this wonderful Piet list, Merry Christmas and a Happy New Year. Thanks, Arden Adamson aadamson@wnmdag.org ________________________________ From: owner-pietenpol-list-server@matronics.com on behalf of dwilson Sent: Sun 12/23/2007 7:57 PM Subject: Pietenpol-List: Re: Plans Page Missing? Greg, I spoke with Goldie Hoopman just a couple of weeks ago. She is doing great! A couple of months ago she gave me dozens of drawings that she had stored in her basement. She no longer sells plans and when people inquire she tells them to contact Don Pietenpol in Rochester, MN. However, there is an original drawing of the Jenny style landing gear in the many plan drawings that I obtained from Mrs. Hoopman. I dont think that there would be anything wrong with sending someone a copy if they needed one. The drawing I have is 11 X 17. I may even be able to scan the image and email it as a pdf. Dan Wilson Austin, MN Read this topic online here: http://forums.matronics.com/viewtopic.php?p=153923#153923


    Message 14


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:20:18 PM PST US
    From: "Glenn Thomas" <glennthomas@flyingwood.com>
    Subject: Re: Plans Page Missing?
    Same here. The quality of my enlargements is fair at best. I think I can make out most of the dimensions but would pay for something a little cleaner and easier to read. On 12/23/07, Arden Adamson <aadamson@wnmdag.org> wrote: > > Dan, > > I've been following the discussions about the Jenny style landing gear. I > am building mine as we speak. It would certainly be appreciated if I could > somehow obtain a copy of the 11 X 17 drawings. If cost is involved, I'd > gladly pay. > > To all on this wonderful Piet list, Merry Christmas and a Happy New Year. > > Thanks, > Arden Adamson > aadamson@wnmdag.org > > > ________________________________ > > From: owner-pietenpol-list-server@matronics.com on behalf of dwilson > Sent: Sun 12/23/2007 7:57 PM > To: pietenpol-list@matronics.com > Subject: Pietenpol-List: Re: Plans Page Missing? > > > > Greg, I spoke with Goldie Hoopman just a couple of weeks ago. She is > doing great! A couple of months ago she gave me dozens of drawings that she > had stored in her basement. She no longer sells plans and when people > inquire she tells them to contact Don Pietenpol in Rochester, MN. However, > there is an original drawing of the Jenny style landing gear in the many > plan drawings that I obtained from Mrs. Hoopman. I dont think that there > would be anything wrong with sending someone a copy if they needed one. The > drawing I have is 11 X 17. I may even be able to scan the image and email > it as a pdf. > > Dan Wilson > Austin, MN > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=153923#153923 > > -- Glenn Thomas Storrs, CT http://www.flyingwood.com


    Message 15


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:54:15 PM PST US
    Subject: Re: Model A engine
    From: "MF" <ferrari@lakenet.com>
    I found one of the books I've been looking for. The title is "The Model A Engine" by William H. Mcree and Paul H. Mcree. Looks very informative, sort of a step-by-step rebuild guide with a good definition of each part and what it does. Matt Read this topic online here: http://forums.matronics.com/viewtopic.php?p=153945#153945


    Message 16


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:00:57 PM PST US
    From: "gcardinal" <gcardinal@comcast.net>
    Subject: Re: Plans Page Missing?
    This might be good info to post on Chris Tracy's website........ Cheers, Greg ----- Original Message ----- From: "dwilson" <marwilson@charter.net> Sent: Sunday, December 23, 2007 7:57 PM Subject: Pietenpol-List: Re: Plans Page Missing? > > Greg, I spoke with Goldie Hoopman just a couple of weeks ago. She is > doing great! A couple of months ago she gave me dozens of drawings that > she had stored in her basement. She no longer sells plans and when people > inquire she tells them to contact Don Pietenpol in Rochester, MN. > However, there is an original drawing of the Jenny style landing gear in > the many plan drawings that I obtained from Mrs. Hoopman. I dont think > that there would be anything wrong with sending someone a copy if they > needed one. The drawing I have is 11 X 17. I may even be able to scan the > image and email it as a pdf. > > Dan Wilson > Austin, MN > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=153923#153923 > > >




    Other Matronics Email List Services

  • Post A New Message
  •   pietenpol-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Pietenpol-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/pietenpol-list
  • Browse Pietenpol-List Digests
  •   http://www.matronics.com/digest/pietenpol-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --