---------------------------------------------------------- Pietenpol-List Digest Archive --- Total Messages Posted Tue 07/21/09: 23 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:24 AM - Re: Finally, work space! (Dan Yocum) 2. 09:43 AM - Driving to OSH from Brodhead (Patrick Panzera) 3. 11:58 AM - Re: McCulloch drone engine (Barry Davis) 4. 12:22 PM - Re: Finally, work space! (airlion@bellsouth.net) 5. 12:40 PM - Re: McCulloch drone engine (Jerry Dotson) 6. 01:18 PM - Chicago TFR, Thursday 7/23 (Dan Yocum) 7. 01:35 PM - TFRs for this Week (Wayne Bressler) 8. 01:44 PM - TFRs Again (Wayne Bressler) 9. 01:48 PM - Re: TFRs for this Week (Gary Boothe) 10. 01:55 PM - Re: Finally, work space! (Dick N.) 11. 02:10 PM - weather (helspersew@aol.com) 12. 02:10 PM - Re: TFRs for this Week (Wayne Bressler) 13. 02:17 PM - Re: McCulloch drone engine (Will42) 14. 02:24 PM - Re: weather (Bill Church) 15. 02:34 PM - Re: weather (helspersew@aol.com) 16. 03:52 PM - Re: opinions on ebay motorcycle wheels? (Jim Malley) 17. 04:40 PM - Re: Finally, work space! (airlion@bellsouth.net) 18. 07:42 PM - Re: weather (Lloyd Smith) 19. 08:12 PM - Re: TFRs for this Week (shad bell) 20. 08:42 PM - if flying....be aware of Presidential TFR's and Air Show TFR north of Mitchell Field, Milwaukee (Cuy, Michael D. (GRC-RXD0)[ASRC Aerospace Corporation]) 21. 08:51 PM - Re: TFRs for this Week (Gary Boothe) 22. 08:51 PM - brodhead (RBush96589@aol.com) 23. 09:16 PM - Re: brodhead (shad bell) ________________________________ Message 1 _____________________________________ Time: 08:24:23 AM PST US From: Dan Yocum Subject: Re: Pietenpol-List: Finally, work space! Ryan, I have some shop equipment that you're welcome to borrow if you want - an *old* 7 1/4" Craftsman pedestal table saw, circa 1930-40's - it works very well, tracks straight and the fence is tight, but it doesn't have any sort of ruler - also have a flat plate to attach sanding disks so it could be used for that, too; a Victor oxy-acetylene torch set; hand drill; hand grinder; hand jig saw; a couple of hand planers; maybe some other stuff. It's all just sitting around the garage right now collecting dust - I don't have much time to use it and no projects to use them on so if you need something, let me know. See you at Brodhead, Dan -- Dan Yocum Fermilab 630.840.6509 yocum@fnal.gov, http://fermigrid.fnal.gov Fermilab. Just zeros and ones. ________________________________ Message 2 _____________________________________ Time: 09:43:25 AM PST US From: "Patrick Panzera" Subject: Pietenpol-List: Driving to OSH from Brodhead Hey gang, I'll be leaving the field at Brodhead right after the launch on Sunday morning. If anyone needs me to tote gear, I'll have room in my car. Contact me off list. Pat Editor@ContactMagazine.com ________________________________ Message 3 _____________________________________ Time: 11:58:58 AM PST US From: "Barry Davis" Subject: RE: Pietenpol-List: McCulloch drone engine I have one that is disassembled. Can take pics of it for you. Heading to Oshkosh on Friday Barry Davis -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Will42 Sent: Monday, July 20, 2009 5:17 PM Subject: Pietenpol-List: McCulloch drone engine I need a McCulloch drone engine for a project. If you have one or more for sale and/or parts, please contact me. will@cctc.net Thanks so much.........Will Read this topic online here: http://forums.matronics.com/viewtopic.php?p=253970#253970 ________________________________ Message 4 _____________________________________ Time: 12:22:53 PM PST US From: airlion@bellsouth.net Subject: Re: Pietenpol-List: Finally, work space! Well, I had my cessna 140 all loaded up this morning to fly to Brodhead,and lo and behold,when I checked with flight service for weather and TFR's they said that for the next 5 days it will be rain and tystems. Not a good weekend for camping and socializing with all you good people. So I will just stay here in lAGRANGE, Ga. and work on my Piet. Just a few more projects and it will be ready for inspection. If the weekend turns out better weatherwise please let me know so I can weep more than I am now. Cheers, Gardiner Mason -------------- Original message ---------------------- From: Dan Yocum > > > Ryan, > > I have some shop equipment that you're welcome to borrow if you want - > an *old* 7 1/4" Craftsman pedestal table saw, circa 1930-40's - it works > very well, tracks straight and the fence is tight, but it doesn't have > any sort of ruler - also have a flat plate to attach sanding disks so it > could be used for that, too; a Victor oxy-acetylene torch set; hand > drill; hand grinder; hand jig saw; a couple of hand planers; maybe some > other stuff. > > It's all just sitting around the garage right now collecting dust - I > don't have much time to use it and no projects to use them on so if you > need something, let me know. > > See you at Brodhead, > Dan > > > -- > Dan Yocum > Fermilab 630.840.6509 > yocum@fnal.gov, http://fermigrid.fnal.gov > Fermilab. Just zeros and ones. > > > > ________________________________ Message 5 _____________________________________ Time: 12:40:38 PM PST US Subject: Pietenpol-List: Re: McCulloch drone engine From: "Jerry Dotson" I found one on Craig's list Seattle for $150. http://seattle.craigslist.org/tac/pts/1279684749.html Read this topic online here: http://forums.matronics.com/viewtopic.php?p=254163#254163 ________________________________ Message 6 _____________________________________ Time: 01:18:35 PM PST US From: Dan Yocum Subject: Pietenpol-List: Chicago TFR, Thursday 7/23 Just a heads up: http://tfr.faa.gov/save_pages/detail_9_0041.html -- Dan Yocum Fermilab 630.840.6509 yocum@fnal.gov, http://fermigrid.fnal.gov Fermilab. Just zeros and ones. ________________________________ Message 7 _____________________________________ Time: 01:35:00 PM PST US From: Wayne Bressler Subject: Pietenpol-List: TFRs for this Week All, Be careful en route to Brodhead, Baraboo, and Oshkosh. Your President will be occupying a large amount of airspace on the 23rd. First in Cleveland, Ohio, and later that day he'll be in Chicago, Illinois. DO NOT VIOLATE THESE TFRs!!! Cleveland, OH - July 23 from 1550z to 2055z. Multiple areas. FDC NOTAM Number 9/0023 Chicago, IL - From July 23 at 2100z to July 24 at 0200z. Multiple areas. FDC NOTAM Number 9/0041 These are big 30 nm TFRs, so please plan accordingly. If you have any questions, call Flight Service before you go! Have fun at the shows!!! Wayne Bressler Jr. Taildraggers, Inc. taildraggersinc.com Sent from the phone that made the Blackberry obsolete. ________________________________ Message 8 _____________________________________ Time: 01:44:01 PM PST US From: Wayne Bressler Subject: Pietenpol-List: TFRs Again If you want to see details for any TFR, go to tfr.faa.gov Wayne Bressler Jr. Taildraggers, Inc. taildraggersinc.com Sent from the phone that made the Blackberry obsolete. ________________________________ Message 9 _____________________________________ Time: 01:48:00 PM PST US From: "Gary Boothe" Subject: RE: Pietenpol-List: TFRs for this Week I can't believe he would schedule his trips the same time as Brodhead....sheesh! Gary Boothe Cool, Ca. Pietenpol WW Corvair Conversion Tail done, Fuselage on gear (13 ribs down.) Do not archive -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Wayne Bressler Sent: Tuesday, July 21, 2009 1:33 PM TailwindForum@yahoogroups.com Subject: Pietenpol-List: TFRs for this Week All, Be careful en route to Brodhead, Baraboo, and Oshkosh. Your President will be occupying a large amount of airspace on the 23rd. First in Cleveland, Ohio, and later that day he'll be in Chicago, Illinois. DO NOT VIOLATE THESE TFRs!!! Cleveland, OH - July 23 from 1550z to 2055z. Multiple areas. FDC NOTAM Number 9/0023 Chicago, IL - From July 23 at 2100z to July 24 at 0200z. Multiple areas. FDC NOTAM Number 9/0041 These are big 30 nm TFRs, so please plan accordingly. If you have any questions, call Flight Service before you go! Have fun at the shows!!! Wayne Bressler Jr. Taildraggers, Inc. taildraggersinc.com Sent from the phone that made the Blackberry obsolete. ________________________________ Message 10 ____________________________________ Time: 01:55:09 PM PST US From: "Dick N." Subject: Re: Pietenpol-List: Finally, work space! Gardiner I am in St. Paul, Mn. From here the weather looks pretty good. There is always a chance of Tstms all summer. Greg Cardinal and I are each flying our Piets tomorrow and should be sitting around with a cold beer by happy hour time. Dick ----- Original Message ----- From: Sent: Tuesday, July 21, 2009 1:52 PM Subject: Re: Pietenpol-List: Finally, work space! Well, I had my cessna 140 all loaded up this morning to fly to Brodhead,and lo and behold,when I checked with flight service for weather and TFR's they said that for the next 5 days it will be rain and tystems. Not a good weekend for camping and socializing with all you good people. So I will just stay here in lAGRANGE, Ga. and work on my Piet. Just a few more projects and it will be ready for inspection. If the weekend turns out better weatherwise please let me know so I can weep more than I am now. Cheers, Gardiner Mason -------------- Original message ---------------------- From: Dan Yocum > > > Ryan, > > I have some shop equipment that you're welcome to borrow if you want - > an *old* 7 1/4" Craftsman pedestal table saw, circa 1930-40's - it works > very well, tracks straight and the fence is tight, but it doesn't have > any sort of ruler - also have a flat plate to attach sanding disks so it > could be used for that, too; a Victor oxy-acetylene torch set; hand > drill; hand grinder; hand jig saw; a couple of hand planers; maybe some > other stuff. > > It's all just sitting around the garage right now collecting dust - I > don't have much time to use it and no projects to use them on so if you > need something, let me know. > > See you at Brodhead, > Dan > > > -- > Dan Yocum > Fermilab 630.840.6509 > yocum@fnal.gov, http://fermigrid.fnal.gov > Fermilab. Just zeros and ones. > > ________________________________ Message 11 ____________________________________ Time: 02:10:14 PM PST US Subject: Pietenpol-List: weather From: helspersew@aol.com WX?at Poplar Grove IL is VFR, overcast with very light sprinkles. But I see on radar that there is an area of yellow heading this way. Dan Helsper ________________________________ Message 12 ____________________________________ Time: 02:10:15 PM PST US From: Wayne Bressler Subject: Re: Pietenpol-List: TFRs for this Week Don't feel too down about it. He shut down a 30 nm chunk of busy New York airspace recently to take his wife out for a date. Do not archive. Wayne Bressler Jr. Taildraggers, Inc. taildraggersinc.com Sent from the phone that made the Blackberry obsolete. On Jul 21, 2009, at 4:43 PM, "Gary Boothe" wrote: > > > > I can't believe he would schedule his trips the same time as > Brodhead....sheesh! > > Gary Boothe > Cool, Ca. > Pietenpol > WW Corvair Conversion > Tail done, Fuselage on gear > (13 ribs down.) > Do not archive > > -----Original Message----- > From: owner-pietenpol-list-server@matronics.com > [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Wayne > Bressler > Sent: Tuesday, July 21, 2009 1:33 PM > To: dcpilots@yahoogroups.com; pietenpol-list@matronics.com; > TailwindForum@yahoogroups.com > Subject: Pietenpol-List: TFRs for this Week > > > > All, > > Be careful en route to Brodhead, Baraboo, and Oshkosh. > > Your President will be occupying a large amount of airspace on the > 23rd. First in Cleveland, Ohio, and later that day he'll be in > Chicago, Illinois. > > DO NOT VIOLATE THESE TFRs!!! > > Cleveland, OH - July 23 from 1550z to 2055z. Multiple areas. FDC > NOTAM Number 9/0023 > > Chicago, IL - From July 23 at 2100z to July 24 at 0200z. Multiple > areas. FDC NOTAM Number 9/0041 > > These are big 30 nm TFRs, so please plan accordingly. > > If you have any questions, call Flight Service before you go! > > Have fun at the shows!!! > > Wayne Bressler Jr. > Taildraggers, Inc. > taildraggersinc.com > > Sent from the phone that made the Blackberry obsolete. > > ________________________________ Message 13 ____________________________________ Time: 02:17:45 PM PST US Subject: Pietenpol-List: Re: McCulloch drone engine From: "Will42" bed(at)mindspring.com wrote: > I have one that is disassembled. Can take pics of it for you. Heading to > Oshkosh on Friday > Barry Davis > > -- I would be interested to see what you have. Pictures, condition and price if you can. will@cctc.net Thanks so much.........Will Read this topic online here: http://forums.matronics.com/viewtopic.php?p=254189#254189 ________________________________ Message 14 ____________________________________ Time: 02:24:03 PM PST US Subject: RE: Pietenpol-List: weather From: "Bill Church" That really doesn't sound good ... yellow sprinkles. Better get the umbrella out. as usual, Do Not Archive ________________________________ From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of helspersew@aol.com Sent: Tuesday, July 21, 2009 5:08 PM Subject: Pietenpol-List: weather WX at Poplar Grove IL is VFR, overcast with very light sprinkles. But I see on radar that there is an area of yellow heading this way. ________________________________ Message 15 ____________________________________ Time: 02:34:31 PM PST US Subject: Re: Pietenpol-List: weather From: helspersew@aol.com Yea, that is the precursor to "raining cats and dogs" please do not archive -----Original Message----- From: Bill Church Sent: Tue, Jul 21, 2009 4:22 pm Subject: RE: Pietenpol-List: weather That really doesn't sound good ... yellow sprinkles. Better get the umbrella out. ? as usual, ? Do Not Archive From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of helspersew@aol.com Sent: Tuesday, July 21, 2009 5:08 PM Subject: Pietenpol-List: weather WX?at Poplar Grove IL is VFR, overcast with very light sprinkles. But I see on radar that there is an area of yellow heading this way. ________________________________ Message 16 ____________________________________ Time: 03:52:03 PM PST US From: "Jim Malley" Subject: Re: Pietenpol-List: opinions on ebay motorcycle wheels? I first used narrow motorcycle wheels with a 5/8 inch axle. Under normal abuse the axle (a six inch bolt) did not bend even though it was supported only on one end; nor did the wheels give in due to side loads. However, when I intentionally ground looped it to avoid a tree during an off airport landing, the wheel collapsed, there was almost no other damage (the bolt was also bent a few degrees). Unable to find an exact match, I made a new pair with a six inch width and a 1-1/4 axle. Again, normal abuse was fine, as would be expected, but a few years later when I went into a two foot deep ditch the wheels proved their strength by holding up fine but they transmitted the forces up the landing gear leg and the fuselage side was torn open. That repair took a lot longer. Jim Malley ----- Original Message ----- From: Ken Chambers To: pietenpol-list@matronics.com Sent: Monday, July 20, 2009 2:10 PM Subject: Re: Pietenpol-List: opinions on ebay motorcycle wheels? Thats a sweet setup Gary. Never thought of that. I might be able to make something like that work. For tyhe dirt bike wheels I'm looking at, I've emailed the seller to ask the axle diameter but I haven't heard back. Also trying to figure out how wide the spoke is, hub to hub. Speaking of brakes, there is a flange with four holes on one side. You can see it in the attached photo On Mon, Jul 20, 2009 at 10:46 AM, Gary Boothe wrote: Ken, I have no machining skills, or tools, either. Attached is a picture of how I made it happen: Just figured out a way to chuck the axle to one of my =BD=94 drills and used wet-or-dry paper to remove the steel; took about 45 minutes ' 1 hour per axle. A solid axle is being used by many, but you did not say how big of an axle your bearings might take. Gary Boothe Cool, Ca. Pietenpol WW Corvair Conversion Tail done, Fuselage on gear (13 ribs down=85) ------------------------------------------------------------------------- --- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Ken Chambers Sent: Monday, July 20, 2009 8:21 AM To: pietenpol-list@matronics.com Subject: Re: Pietenpol-List: opinions on ebay motorcycle wheels? Thanks Gary. That's a beautiful setup you have. I have no machining skills or tools so I'm trying to figure out a way to do it as simply as possible with the split axle gear. I wonder if anyone uses solid axles? Heavier, sure, but would it hold up. On a motorcycle it's supported on both ends by the fork. On Mon, Jul 20, 2009 at 8:03 AM, Gary Boothe wrote: Ken, You will likely get the usual discussion on the pros & cons of using motorcycle wheels, so you will have to make your own decision on that. I bought 21=94 Harley Sportster wheels with the bearings replaced to receive 1=94 axles. I then used Dick Navatril=92s idea of an 1 =BC=94 axle (tube) with step-down tubes installed. My step-down tubes run in about 18=94 on each end, with the 1=94 OD axle being the last. I had to actually mil this one as it was .004=94 over 1=94! =93Wheels 1=94 shows that the Harley hub has 5 pre-drilled and threaded holes for the disc brake set up on motorcycles. I match-drilled this layout on my drub brake shoe and attached the shoe with a cover disc (=931187=94). The wheels you are showing have a very interesting spoke attach method, and you may be challenged to find a way to attach brakes, either disc or drum. I am certainly no expert, and mine is not flight-proven. Good luck!! Gary Boothe Cool, Ca. Pietenpol WW Corvair Conversion Tail done, Fuselage on gear (13 ribs down=85) ------------------------------------------------------------------------- --- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Ken Chambers Sent: Sunday, July 19, 2009 3:59 PM To: pietenpol-list@matronics.com Subject: Pietenpol-List: opinions on ebay motorcycle wheels? Anyone with motorcycle wheel experience care to offer an opinion on these dirt bike wheels? Think they'd be strong enough to handle the side loads? Any thoughts on attaching brakes? Machining them for a bigger axle? Or could keep the existing bearings with a solid axle? I've emailed to ask hub width and axle diameter but haven't heard back yet. Looks like the hub width is maybe 3 inches? http://contact.ebay.com/ebaymotors/ws/eBayISAPI.dll?ShowCoreAskSellerQues tion&&iid=190248078501&requested=giovannibikes&frm=284&redirect=0 &noredirectfaq=1&SSPageName=PageAskSellerQuestion_FAQ -- Ken Chambers 512-796-1798 http://www.matronics.com/Navigator?Pietenpol-Listhttp://forums.matronics. comhttp://www.matronics.com/contribution -- Ken Chambers 512-796-1798 ________________________________ Message 17 ____________________________________ Time: 04:40:21 PM PST US From: airlion@bellsouth.net Subject: Re: Pietenpol-List: Finally, work space! Dick, thanks for the reply and I will be thinking about you guys this week. Next week to kosh should be pretty good wx wise. Gardiner. -------------- Original message ---------------------- From: "Dick N." > > > Gardiner > I am in St. Paul, Mn. From here the weather looks pretty good. There is > always a chance of Tstms all summer. Greg Cardinal and I are each flying > our Piets tomorrow and should be sitting around with a cold beer by happy > hour time. > Dick > ----- Original Message ----- > From: > To: > Sent: Tuesday, July 21, 2009 1:52 PM > Subject: Re: Pietenpol-List: Finally, work space! > > > > Well, I had my cessna 140 all loaded up this morning to fly to > Brodhead,and lo and behold,when I checked with flight service for weather > and TFR's they said that for the next 5 days it will be rain and tystems. > Not a good weekend for camping and socializing with all you good people. So > I will just stay here in lAGRANGE, Ga. and work on my Piet. Just a few more > projects and it will be ready for inspection. If the weekend turns out > better weatherwise please let me know so I can weep more than I am now. > Cheers, Gardiner Mason > -------------- Original message ---------------------- > From: Dan Yocum > > > > > > Ryan, > > > > I have some shop equipment that you're welcome to borrow if you want - > > an *old* 7 1/4" Craftsman pedestal table saw, circa 1930-40's - it works > > very well, tracks straight and the fence is tight, but it doesn't have > > any sort of ruler - also have a flat plate to attach sanding disks so it > > could be used for that, too; a Victor oxy-acetylene torch set; hand > > drill; hand grinder; hand jig saw; a couple of hand planers; maybe some > > other stuff. > > > > It's all just sitting around the garage right now collecting dust - I > > don't have much time to use it and no projects to use them on so if you > > need something, let me know. > > > > See you at Brodhead, > > Dan > > > > > > -- > > Dan Yocum > > Fermilab 630.840.6509 > > yocum@fnal.gov, http://fermigrid.fnal.gov > > Fermilab. Just zeros and ones. > > > > > > > > > > > > > > > > > > > > > ________________________________ Message 18 ____________________________________ Time: 07:42:43 PM PST US Subject: Re: Pietenpol-List: weather From: Lloyd Smith Rain all day in Brodhead, mostly light showers with fairly high ceiling. We're camped just nw of Brodhead town. Looking forward to Thursday. On Tue, Jul 21, 2009 at 5:29 PM, wrote: > Yea, that is the precursor to "raining cats and dogs" > > please do not archive > > > -----Original Message----- > From: Bill Church > To: pietenpol-list@matronics.com > Sent: Tue, Jul 21, 2009 4:22 pm > Subject: RE: Pietenpol-List: weather > > That really doesn't sound good ... yellow sprinkles. > Better get the umbrella out. > > as usual, > > Do Not Archive > > ------------------------------ > *From:* owner-pietenpol-list-server@matronics.com [ > mailto:owner-pietenpol-list-server@matronics.com] > *On Behalf Of *helspersew@aol.com > *Sent:* Tuesday, July 21, 2009 5:08 PM > *To:* pietenpol-list@matronics.com > *Subject:* Pietenpol-List: weather > > WX at Poplar Grove IL is VFR, overcast with very light sprinkles. But I > see on radar that there is an area of yellow heading this way. > > * > * > > * > > * > > * > > * > > -- "Politics is the art of looking for trouble, finding it whether it exists or not, diagnosing it incorrectly, and applying the wrong remedy." --British publisher and writer Ernest Benn (1875-1954) ________________________________ Message 19 ____________________________________ Time: 08:12:55 PM PST US From: shad bell Subject: RE: Pietenpol-List: TFRs for this Week I sure as hell did not vote for that piece of @$#% Shad ________________________________ Message 20 ____________________________________ Time: 08:42:52 PM PST US From: "Cuy, Michael D. (GRC-RXD0)[ASRC Aerospace Corporation]" Subject: Pietenpol-List: if flying....be aware of Presidential TFR's and Air Show TFR north of Mitchell Field, Milwaukee For anyone transiting thru the Cleveland Class B airspace on Thursday-- beware that President Obama's visit has a TFR going into effect at 11:50 AM thru 5:00 pm. Coincidentally, another TFR goes into effect at 5 pm EDT for CHICAGO.....until later that same evening. (again, President Obama) Also take note that just north of Milwaukee (if you're flying up the shoreline of Lake Michigan to Oshkosh) there is a Thursday thru Sunday TFR north of Mitchell Field for both daytime and night time performances/air show routines. Check out all TFR's at your favorite web site or the FAA site: http://tfr.faa.gov/tfr2/list.html (TFR= Temporary Flight Restriction) Should you be unfortunate enough to bust a TFR accidentally, know the procedures should you be intercepted....they like it when you cooperate much better:) http://www.aopa.org/whatsnew/newsitems/2001/010918intercept.html ________________________________ Message 21 ____________________________________ Time: 08:51:56 PM PST US From: "Gary Boothe" Subject: RE: Pietenpol-List: TFRs for this Week Shad, I'd like to buy you a beer...after all the flying's done, of course. I'll be in Brodhead Thursday morning... Gary Boothe Cool, Ca. Pietenpol WW Corvair Conversion Tail done, Fuselage on gear (13 ribs down.) Do not archive -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of shad bell Sent: Tuesday, July 21, 2009 8:10 PM Subject: RE: Pietenpol-List: TFRs for this Week I sure as hell did not vote for that piece of @$#% Shad ________________________________ Message 22 ____________________________________ Time: 08:51:57 PM PST US From: RBush96589@aol.com Subject: Pietenpol-List: brodhead Shad, When are you and your dad planning on leaving for Brodhead? I am shooting for early Thursday if the weather permits.how about you Jack? Randy Bush NX294RB do not archive **************What's for dinner tonight? Find quick and easy dinner ideas for any occasion. (http://food.aol.com/dinner-tonight?ncid=emlcntusfood00000009) ________________________________ Message 23 ____________________________________ Time: 09:16:38 PM PST US From: shad bell Subject: Re: Pietenpol-List: brodhead Randy, We plan on Thurs morning, I guess We'll have to light the afterburners to stay ahead of our tax dollars, I mean the big shiny 747 with the presidential seal. Hope to se you there. Shad > > > > > > Shad, > When are you and your dad planning on leaving > for Brodhead? > I am shooting for early Thursday if the > weather permits.how > about you Jack? > > Randy Bush > NX294RB > do not archive What's for dinner tonight? > Find quick > and easy dinner ideas for any occasion. > > > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message pietenpol-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Pietenpol-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/pietenpol-list Browse Digests http://www.matronics.com/digest/pietenpol-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.