Today's Message Index:
----------------------
1. 09:05 AM - West Coast Pietenpol Meet (Michael Groah)
2. 12:23 PM - Re: West Coast Pietenpol Meet (Jim)
3. 12:55 PM - first really big mistake! (bcolleran)
4. 01:04 PM - Re: first really big mistake! (AMsafetyC@aol.com)
5. 08:38 PM - Re: first really big mistake! (dgaldrich)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | West Coast Pietenpol Meet |
Ok everyone, I just wanted to send out a reminder to those that are attending!
We're only a couple days away from the Pietenpol gathering at Frazier Lake Airpark
in California. The gathering is this Saturday June 5th. I'm looking forward
to meeting people and talking about Pietenpols. I know we're going to have
a good time.
Mike Groah
Do not archive
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: West Coast Pietenpol Meet |
Oops, forgot to change to plain text. See you there Mike,
Jim
Jim Boyer
Santa Rosa, CA
Pietenpol on wheels
Tail surfaces done
Wing ribs done
Corvair engine
On Jun 2, 2010, Michael Groah <dskogrover@yahoo.com> wrote:
Ok everyone, I just wanted to send out a reminder to those that are attending!
We're only a couple days away from the Pietenpol gathering at Frazier Lake Airpark
in California. The gathering is this Saturday June 5th. I'm looking forward
to meeting people and talking about Pietenpols. I know we're going to have
a good time.
Mike Groah
Do not archive
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | first really big mistake! |
While looking at my horizontal stab, which I had already seceretly messed up, I
thought it may have looked a little larger than 18". After measuring it sure
in deed it was! Gosh darn it! I guess I must be using a bad ruler. Well back
to the new jig and it will all be done by tomorrow night. Good thing is I
get to play with my new table saw! Wish me luck! This time I'll use the correct
ruler.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=299767#299767
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: first really big mistake! |
Better keep an eye on the saw blade, new saws have big sharp teeth that
like to bite hands and fingers while the operator is busy looking at the
ruler, admiring the cut and attending to other things!
Do not archive
But do pay attention or you'll learn all about the blood and tears part
only leaving the cold sweat for the time traveling to the hospital.
Safe in the morning, safe all day!
In a message dated 6/2/2010 3:56:01 P.M. Eastern Daylight Time,
bcolleran@comcast.net writes:
--> Pietenpol-List message posted by: "bcolleran" <bcolleran@comcast.net>
While looking at my horizontal stab, which I had already seceretly messed
up, I thought it may have looked a little larger than 18". After measuring
it sure in deed it was! Gosh darn it! I guess I must be using a bad
ruler. Well back to the new jig and it will all be done by tomorrow night.
Good thing is I get to play with my new table saw! Wish me luck! This time
I'll use the correct ruler.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=299767#299767
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: first really big mistake! |
You could have left it. The extra weight would mean less beer needed for w&b.
On second thought, make it 16 inches....
Do not archive.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=299810#299810
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|