Today's Message Index:
----------------------
1. 08:43 AM - Re: new Piet on the block (dgaldrich)
2. 09:10 AM - Control Stick Question (Jack)
3. 12:19 PM - Re: Another Turtle Deck Question (echobravo4)
4. 01:13 PM - Re: Control Stick Question (Gene Rambo)
5. 01:28 PM - Making Progress (Dangerous Dave)
6. 07:36 PM - Re: Another Turtle Deck Question (K5YAC)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: new Piet on the block |
And maybe pics of the work in progress....
Dave Aldrich
do not archive
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=317579#317579
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Control Stick Question |
Regarding the bearing bored to =BC inch x 1-1/4=94 long at the bottom of
the
stick and going through the main horizontal tube=85does it also go
through the
metal straps on either side of the control stick that bolt to the
control
tube? Or after welding, is the bearing cut off flush with the
horizontal
control tube (7/8=94), and then straps butt up against it. This is show
on
page 4 of the plans.
Thanks,
Jack
DSM
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Another Turtle Deck Question |
Hey Mark;
fwiw, i just got some 9' TE sections from AS&S and they
came fedex ground.
Earl
--------
Earl Brown
I may not have gone where I intended to go, but I think I have ended up where I
intended to be.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=317599#317599
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Control Stick Question |
neither. The bearing tube is somewhat woder than the tube and square on th
e ends. The straps on the bottom of the stick bolt to the outside of the b
earing tube and rotate om it.
Gene
From: jack@textors.com
Subject: Pietenpol-List: Control Stick Question
Regarding the bearing bored to =BC inch x 1-1/4=94 long at the bottom of th
e stick and going through the main horizontal tube=85does it also go throug
h the metal straps on either side of the control stick that bolt to the con
trol tube? Or after welding=2C is the bearing cut off flush with the horiz
ontal control tube (7/8=94)=2C and then straps butt up against it. This is
show on page 4 of the plans.
Thanks=2C
Jack
DSM
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Howdy,here are some pics of this weekends progress.
Dave
--------
Building a Piet
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=317608#317608
Attachments:
http://forums.matronics.com//files/piet_10_30_018_129.jpg
http://forums.matronics.com//files/piet_10_30_001_131.jpg
http://forums.matronics.com//files/piet_10_30_015_112.jpg
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Another Turtle Deck Question |
Wow! 9 footers! I called and found out that they will definitely ship anything
up to 8'. I'm planning to get some spruce on order tomorrow.
--------
Mark Chouinard
Wings, Center Section and Empannage framed up - Working on Fuselage
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=317641#317641
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|