---------------------------------------------------------- Pietenpol-List Digest Archive --- Total Messages Posted Fri 01/07/11: 25 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:26 AM - Re: Re: Elevator cables (Jack Phillips) 2. 05:13 AM - Re: MY NEW ENGINE (Frank Metcalfe) 3. 05:38 AM - definition of UHMW for Ray (Cuy, Michael D. (GRC-RXD0)[ASRC AEROSPACE CORP]) 4. 07:23 AM - Re: Elevator cables (899PM) 5. 07:38 AM - Re: Tail wheel (kevinpurtee) 6. 07:56 AM - Re: Re: Tail wheel (Gene & Tammy) 7. 08:07 AM - Re: Re: Tail wheel (Jack Phillips) 8. 08:14 AM - Re: Elevator cables (Bill Church) 9. 08:19 AM - Re: Re: Tail wheel (Gboothe5) 10. 08:34 AM - Re: Re: Tail wheel (Gene & Tammy) 11. 08:40 AM - Re: Re: Tail wheel (Gene & Tammy) 12. 08:49 AM - New List Member? (John Hofmann) 13. 09:19 AM - Re: New List Member? (Gboothe5) 14. 09:33 AM - Re: New List Member? (John Hofmann) 15. 09:35 AM - Re: definition of UHMW for Ray (DOMIT) 16. 10:50 AM - Re: definition of UHMW for Ray (Ray Krause) 17. 11:03 AM - Re: Re: Elevator cables (Ray Krause) 18. 12:54 PM - Re: Re: Tail wheel (Jim Markle) 19. 01:46 PM - Re: Re: definition of UHMW for Ray (KM Heide CPO/FAAOP) 20. 03:13 PM - Re: Re: definition of UHMW for Ray (Gary Boothe) 21. 05:25 PM - Re: Re: definition of UHMW for Ray (Charles Campbell) 22. 05:36 PM - Re: Re: definition of UHMW for Ray (Jack Phillips) 23. 06:28 PM - Re: Re: definition of UHMW for Ray (Ryan Mueller) 24. 06:58 PM - Re: New List Member? (kevinpurtee) 25. 07:04 PM - Re: definition of UHMW for Ray (kevinpurtee) ________________________________ Message 1 _____________________________________ Time: 04:26:35 AM PST US From: "Jack Phillips" Subject: RE: Pietenpol-List: Re: Elevator cables Google it. -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Ray Krause Sent: Thursday, January 06, 2011 11:17 PM Subject: Re: Pietenpol-List: Re: Elevator cables --> UHMW? Please give a definition,if you would. I am at this very point with the Sky Scout. Was planning this evening on pulleys, just as jack did; or a piece of 1"thick Teflon with holes in it used as a guide. We use the Teflon in farming as "rubbers" for elevator chains on harvesters. Maybe that is what UHMV is? Thanks and fly SAFELY, Ray Krause Waiex 51YX, Jabiru 3300 (1197), Sensenich wood prop, AeroCarb (#2 needle modified), Dynon D-180, Garmin SL 30 NavCom, Garmin 327 transponder, Garmin Aera 560, nav and strobe lights: 234 hrs. Building Sky Scout... slowly. ----- Original Message ----- From: "899PM" Sent: Thursday, January 06, 2011 8:50 AM Subject: Pietenpol-List: Re: Elevator cables > > I used a 1" x 1" pc of UHMW and drilled two "fairlead" holes thru it. > Weighs less than one of the pulleys alone....never mind the brackets. > Lighter here and there (x100) is good! > > -------- > PAPA MIKE > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=325810#325810 > > > ________________________________ Message 2 _____________________________________ Time: 05:13:17 AM PST US From: Frank Metcalfe Subject: Re: Pietenpol-List: MY NEW ENGINE Yes it can... --- On Thu, 1/6/11, Charles Campbell wrote: From: Charles Campbell Subject: Re: Pietenpol-List: MY NEW ENGINE Water is awfully heavy!- Could-the exhausted steam-be captured-and reused? ----- Original Message ----- From: Kip and Beth Gardner Sent: Thursday, January 06, 2011 8:46 AM Subject: Re: Pietenpol-List: MY NEW ENGINE Wouldn't that be fun to fly behind - get a steam bath while you go - people flying commercial first class would pay a lot for a perk like that :). On Jan 5, 2011, at 11:56 PM, Clif Dawson wrote: http://www.youtube.com/watch?v=nKGy08OVxyM&feature=related href="http://www.matronics.com/Navigator?Pietenpol-List">http://www.matro nics.com/Navigator?Pietenpol-List href="http://forums.matronics.com">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/con tribution href="http://www.matronics.com/Navigator?Pietenpol-List">http://www.matro nics.com/Navigator?Pietenpol-List href="http://forums.matronics.com">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/c ________________________________ Message 3 _____________________________________ Time: 05:38:28 AM PST US From: "Cuy, Michael D. (GRC-RXD0)[ASRC AEROSPACE CORP]" Subject: Pietenpol-List: definition of UHMW for Ray Ray-- Can I Google that for you ? Ultra-high-molecular-weight polyethylene (UHMWPE or sometimes shortened to UHMW), also known as high-modulus polyethylene (HMPE) or high-performance polyethylene (HPPE), is a subset of the thermoplastic polyethylene. It has extremely long chains, with molecular weight numbering in the millions, usually between 2 and 6 million. Mike C. do not archive ________________________________ Message 4 _____________________________________ Time: 07:23:48 AM PST US Subject: Pietenpol-List: Re: Elevator cables From: "899PM" Remember....we are building EXPERIMENTAL. My guess is, the UHMW with the holes thru it will far outlast myself and anyone else on this list. -------- PAPA MIKE Read this topic online here: http://forums.matronics.com/viewtopic.php?p=325897#325897 ________________________________ Message 5 _____________________________________ Time: 07:38:42 AM PST US Subject: Pietenpol-List: Re: Tail wheel From: "kevinpurtee" Hi - There are lots and lots of variation in tailwheels. Look on westcoastpiet.com for a sampling. I personally use the 6" matco from aircraft spruce - has worked well for me. The plane and your kids look great. Take care, Kevin -------- Kevin "Axel" Purtee NX899KP Austin/Georgetown, TX Read this topic online here: http://forums.matronics.com/viewtopic.php?p=325898#325898 ________________________________ Message 6 _____________________________________ Time: 07:56:09 AM PST US From: "Gene & Tammy" Subject: Re: Pietenpol-List: Re: Tail wheel Where is everyone getting their tailwheel springs? Gene In Beautiful West Tennessee -----Original Message----- From: kevinpurtee ________________________________ Message 7 _____________________________________ Time: 08:07:36 AM PST US From: "Jack Phillips" Subject: RE: Pietenpol-List: Re: Tail wheel Which kind, Gene? I've got a leaf spring from a Piper PA-12 that you are welcome to. If you are referring to the coil spring for the BHP design, some use a John Deere spring. I got my spring from McMaster-Carr. As I recall, it was about $13.00 Jack Phillips NX899JP "Icarus Plummet" Raleigh, NC -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Gene & Tammy Sent: Friday, January 07, 2011 10:54 AM Subject: Re: Pietenpol-List: Re: Tail wheel --> Where is everyone getting their tailwheel springs? Gene In Beautiful West Tennessee -----Original Message----- From: kevinpurtee ________________________________ Message 8 _____________________________________ Time: 08:14:04 AM PST US Subject: Pietenpol-List: Re: Elevator cables From: "Bill Church" I have no doubt that UHMW would be an excellent material for a fairlead - low friction, self-lubricating, abrasion resistant, etc. I think the issue in this case is the amount of deflection in the control cable, which in this case, as scaled from the plans, is about 30 degrees, which is much more than should be handled by a fairlead. The issue is the amount of localized flexing that the cable will be subjected to. I would think that if a UHMW block was shaped to a radius equal to the appropriate sized pulley, the net result would be the same as using a pulley. Having said that, there have been countless Air campers built as per the plans, using a hole in a block of spruce, and as far as I know, none have fallen out of the sky as a result of that practice. But sometimes it just makes sense to incorporate newer methods and techniques that are based on safety. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=325902#325902 ________________________________ Message 9 _____________________________________ Time: 08:19:04 AM PST US From: "Gboothe5" Subject: RE: Pietenpol-List: Re: Tail wheel If you're talking the coil spring...John Deere. I couldn't order online, but found the part# and a local dealer who mailed it to me. (gotta dig for the part #) Gary Boothe -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Gene & Tammy Sent: Friday, January 07, 2011 7:54 AM Subject: Re: Pietenpol-List: Re: Tail wheel Where is everyone getting their tailwheel springs? Gene In Beautiful West Tennessee -----Original Message----- From: kevinpurtee ________________________________ Message 10 ____________________________________ Time: 08:34:49 AM PST US From: "Gene & Tammy" Subject: Re: Pietenpol-List: Re: Tail wheel Thanks Gary but I have a friend that is looking for a flat tail spring for his J3 Kitten. Gene -----Original Message----- From: Gboothe5 Sent: Friday, January 07, 2011 10:14 AM Subject: RE: Pietenpol-List: Re: Tail wheel If you're talking the coil spring...John Deere. I couldn't order online, but found the part# and a local dealer who mailed it to me. (gotta dig for the part #) ________________________________ Message 11 ____________________________________ Time: 08:40:46 AM PST US From: "Gene & Tammy" Subject: Re: Pietenpol-List: Re: Tail wheel Thanks Jack. I just called Rich and let him know about McMaster-Carr. Doing good here. Gene -----Original Message----- From: Jack Phillips Sent: Friday, January 07, 2011 10:04 AM Subject: RE: Pietenpol-List: Re: Tail wheel Which kind, Gene? I've got a leaf spring from a Piper PA-12 that you are welcome to. If you are referring to the coil spring for the BHP design, some use a John Deere spring. I got my spring from McMaster-Carr. As I recall, it was about $13.00 Jack Phillips NX899JP "Icarus Plummet" Raleigh, NC ________________________________ Message 12 ____________________________________ Time: 08:49:46 AM PST US From: John Hofmann Subject: Pietenpol-List: New List Member? Do not archive John Hofmann Vice-President, Information Technology The Rees Group, Inc. 2424 American Lane Madison, WI 53704 Phone: 608.443.2468 ext 150 Fax: 608.443.2474 Email: jhofmann@reesgroupinc.com ________________________________ Message 13 ____________________________________ Time: 09:19:45 AM PST US From: "Gboothe5" Subject: RE: Pietenpol-List: New List Member? John, I thought better of you! L (will it ever end?) Gary Boothe Corvair Powered Do not archive From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of John Hofmann Sent: Friday, January 07, 2011 8:47 AM Subject: Pietenpol-List: New List Member? Do not archive John Hofmann Vice-President, Information Technology The Rees Group, Inc. 2424 American Lane Madison, WI 53704 Phone: 608.443.2468 ext 150 Fax: 608.443.2474 Email: jhofmann@reesgroupinc.com ________________________________ Message 14 ____________________________________ Time: 09:33:58 AM PST US From: John Hofmann Subject: Re: Pietenpol-List: New List Member? It is cold here in Wisconsin so I need the "flames" to warm me up. Better than this guy: "Waldo! They're smoking! do not archive John Hofmann Vice-President, Information Technology The Rees Group, Inc. 2424 American Lane Madison, WI 53704 Phone: 608.443.2468 ext 150 Fax: 608.443.2474 Email: jhofmann@reesgroupinc.com On Jan 7, 2011, at 11:15 AM, Gboothe5 wrote: > John, > > I thought better of you! L (will it ever end?) > > Gary Boothe > Corvair Powered > Do not archive > ________________________________ Message 15 ____________________________________ Time: 09:35:27 AM PST US Subject: Pietenpol-List: Re: definition of UHMW for Ray From: "DOMIT" Here is how you source this stuff easily: Go to WalMart... or your local grocery store... or the dollar store. Find cutting boards. That's the white ones. -------- Brad "DOMIT" Smith First rule of ground school: This is the ground... don't hit it going fast. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=325911#325911 ________________________________ Message 16 ____________________________________ Time: 10:50:53 AM PST US From: "Ray Krause" Subject: Re: Pietenpol-List: definition of UHMW for Ray Thanks, Mike! I know how to Google and I had done that just after writing my note. I just thought it might be an abbreviation just used by Piet builders! In my work on hospital boards, I have learned to have abbreviations defined because there are a jillion of them that are unique to the users, not found on the internet. I will be installing a set of double pulleys with cable retainers. Thanks again, Ray ----- Original Message ----- From: "Cuy, Michael D. (GRC-RXD0)[ASRC AEROSPACE CORP]" Sent: Friday, January 07, 2011 5:27 AM Subject: Pietenpol-List: definition of UHMW for Ray > AEROSPACE CORP]" > > Ray-- Can I Google that for you ? > > Ultra-high-molecular-weight polyethylene (UHMWPE or sometimes shortened to > UHMW), also known as high-modulus polyethylene (HMPE) or high-performance > polyethylene (HPPE), is a subset of the thermoplastic polyethylene. It has > extremely long chains, with molecular weight numbering in the millions, > usually between 2 and 6 million. > > > Mike C. > > do not archive > > > ________________________________ Message 17 ____________________________________ Time: 11:03:35 AM PST US From: "Ray Krause" Subject: Re: Pietenpol-List: Re: Elevator cables Thanks, I agree 100%. Two pulleys are not that difficult to install. Ray Krause ----- Original Message ----- From: "Bill Church" Sent: Friday, January 07, 2011 8:11 AM Subject: Pietenpol-List: Re: Elevator cables > > > I have no doubt that UHMW would be an excellent material for a fairlead - > low friction, self-lubricating, abrasion resistant, etc. > I think the issue in this case is the amount of deflection in the control > cable, which in this case, as scaled from the plans, is about 30 degrees, > which is much more than should be handled by a fairlead. The issue is the > amount of localized flexing that the cable will be subjected to. I would > think that if a UHMW block was shaped to a radius equal to the appropriate > sized pulley, the net result would be the same as using a pulley. > Having said that, there have been countless Air campers built as per the > plans, using a hole in a block of spruce, and as far as I know, none have > fallen out of the sky as a result of that practice. But sometimes it just > makes sense to incorporate newer methods and techniques that are based on > safety. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=325902#325902 > > > ________________________________ Message 18 ____________________________________ Time: 12:54:03 PM PST US From: Jim Markle Subject: RE: Pietenpol-List: Re: Tail wheel >From Matronics search: Match: #15 Message: #42567 From: "gcardinal" Subject: Re: springs This is the part number, as posted by Bill Church, for the John Deere spring in case anybody else is looking for the info. John Deere sells a spring that's a perfect match for the specs; its part number is T 143444, and it costs about $9.00. Its outer dia. is 1.5in.; full length( no load ) is 6.73" Bill C -----Original Message----- >From: Gboothe5 >Sent: Jan 7, 2011 10:14 AM >To: pietenpol-list@matronics.com >Subject: RE: Pietenpol-List: Re: Tail wheel > > >If you're talking the coil spring...John Deere. I couldn't order online, but >found the part# and a local dealer who mailed it to me. (gotta dig for the >part #) > >Gary Boothe > >-----Original Message----- >From: owner-pietenpol-list-server@matronics.com >[mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Gene & Tammy >Sent: Friday, January 07, 2011 7:54 AM >To: pietenpol-list@matronics.com >Subject: Re: Pietenpol-List: Re: Tail wheel > > > >Where is everyone getting their tailwheel springs? >Gene In Beautiful West Tennessee > >-----Original Message----- >From: kevinpurtee > > ________________________________ Message 19 ____________________________________ Time: 01:46:29 PM PST US From: KM Heide CPO/FAAOP Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray I have plenty to go around if someone is looking for this material. We have a surplus store that purchased 100's of pounds of this stuff in all thicknesses. Ken Heide Fargo, ND --- On Fri, 1/7/11, DOMIT wrote: > From: DOMIT > Subject: Pietenpol-List: Re: definition of UHMW for Ray > To: pietenpol-list@matronics.com > Date: Friday, January 7, 2011, 11:33 AM > --> Pietenpol-List message posted > by: "DOMIT" > > Here is how you source this stuff easily: Go to > WalMart... or your local grocery store... or the dollar > store. Find cutting boards. That's the white > ones. > > -------- > Brad "DOMIT" Smith > > First rule of ground school: This is the ground... > don't hit it going fast. > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=325911#325911 > > > > > > > > Email Forum - > FAQ, > - MATRONICS WEB FORUMS - > List Contribution Web Site - > -Matt > Dralle, List Admin. > > > > ________________________________ Message 20 ____________________________________ Time: 03:13:39 PM PST US From: "Gary Boothe" Subject: RE: Pietenpol-List: Re: definition of UHMW for Ray Ken, Do you sell wood chippers, too?...sorry, couldn't help it... Gary Boothe Cool, Ca. Pietenpol WW Corvair Conversion, Running! Tail done, Fuselage on gear (23 ribs down) Do not archive -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of KM Heide CPO/FAAOP Sent: Friday, January 07, 2011 1:44 PM Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray I have plenty to go around if someone is looking for this material. We have a surplus store that purchased 100's of pounds of this stuff in all thicknesses. Ken Heide Fargo, ND --- On Fri, 1/7/11, DOMIT wrote: > From: DOMIT > Subject: Pietenpol-List: Re: definition of UHMW for Ray > To: pietenpol-list@matronics.com > Date: Friday, January 7, 2011, 11:33 AM > --> Pietenpol-List message posted > by: "DOMIT" > > Here is how you source this stuff easily: Go to > WalMart... or your local grocery store... or the dollar > store. Find cutting boards. That's the white > ones. > > -------- > Brad "DOMIT" Smith > > First rule of ground school: This is the ground... > don't hit it going fast. > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=325911#325911 > > > > > > > > Email Forum - > FAQ, > - MATRONICS WEB FORUMS - > List Contribution Web Site - > -Matt > Dralle, List Admin. > > > > ________________________________ Message 21 ____________________________________ Time: 05:25:39 PM PST US From: "Charles Campbell" Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray Ken, I might need a piece of fairly thin UHMW to go on my stabilizer where the top elevator cable will hit the top of the stabilizer. What thickness do you think I would need and do they have it in small quantities? Incidentally, how does one apply the stuff -- T88? Chuck ----- Original Message ----- From: "KM Heide CPO/FAAOP" Sent: Friday, January 07, 2011 4:44 PM Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray > > > > I have plenty to go around if someone is looking for this material. We > have a surplus store that purchased 100's of pounds of this stuff in all > thicknesses. > > Ken Heide > Fargo, ND > > > --- On Fri, 1/7/11, DOMIT wrote: > >> From: DOMIT >> Subject: Pietenpol-List: Re: definition of UHMW for Ray >> To: pietenpol-list@matronics.com >> Date: Friday, January 7, 2011, 11:33 AM >> --> Pietenpol-List message posted >> by: "DOMIT" >> >> Here is how you source this stuff easily: Go to >> WalMart... or your local grocery store... or the dollar >> store. Find cutting boards. That's the white >> ones. >> >> -------- >> Brad "DOMIT" Smith >> >> First rule of ground school: This is the ground... >> don't hit it going fast. >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=325911#325911 >> >> >> >> >> >> >> >> Email Forum - >> FAQ, >> - MATRONICS WEB FORUMS - >> List Contribution Web Site - >> -Matt >> Dralle, List Admin. >> >> >> >> > > > ________________________________ Message 22 ____________________________________ Time: 05:36:04 PM PST US From: "Jack Phillips" Subject: RE: Pietenpol-List: Re: definition of UHMW for Ray Nothing sticks to polyethylene, disirregardless of its molecular weight. Try stapling or screwing it down, or just use leather like most Pietenpols do. Jack Phillips NX899JP "Icarus Plummet" Raleigh, NC -----Original Message----- From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Charles Campbell Sent: Friday, January 07, 2011 8:19 PM Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray Ken, I might need a piece of fairly thin UHMW to go on my stabilizer where the top elevator cable will hit the top of the stabilizer. What thickness do you think I would need and do they have it in small quantities? Incidentally, how does one apply the stuff -- T88? Chuck ----- Original Message ----- From: "KM Heide CPO/FAAOP" Sent: Friday, January 07, 2011 4:44 PM Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray > > > > I have plenty to go around if someone is looking for this material. We > have a surplus store that purchased 100's of pounds of this stuff in all > thicknesses. > > Ken Heide > Fargo, ND > > > --- On Fri, 1/7/11, DOMIT wrote: > >> From: DOMIT >> Subject: Pietenpol-List: Re: definition of UHMW for Ray >> To: pietenpol-list@matronics.com >> Date: Friday, January 7, 2011, 11:33 AM >> --> Pietenpol-List message posted >> by: "DOMIT" >> >> Here is how you source this stuff easily: Go to >> WalMart... or your local grocery store... or the dollar >> store. Find cutting boards. That's the white >> ones. >> >> -------- >> Brad "DOMIT" Smith >> >> First rule of ground school: This is the ground... >> don't hit it going fast. >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=325911#325911 >> >> >> >> >> >> >> >> Email Forum - >> FAQ, >> - MATRONICS WEB FORUMS - >> List Contribution Web Site - >> -Matt >> Dralle, List Admin. >> >> >> >> > > > ________________________________ Message 23 ____________________________________ Time: 06:28:57 PM PST US Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray From: Ryan Mueller Snowflakes don't wear leather....come on now. ;) Ryan do not archive On Fri, Jan 7, 2011 at 7:33 PM, Jack Phillips wrote: > pietflyr@bellsouth.net> > > Nothing sticks to polyethylene, disirregardless of its molecular weight. > Try stapling or screwing it down, or just use leather like most Pietenpols > do. > > Jack Phillips > NX899JP "Icarus Plummet" > Raleigh, NC > > -----Original Message----- > From: owner-pietenpol-list-server@matronics.com > [mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of Charles > Campbell > Sent: Friday, January 07, 2011 8:19 PM > To: pietenpol-list@matronics.com > Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray > > > > Ken, I might need a piece of fairly thin UHMW to go on my stabilizer where > the top elevator cable will hit the top of the stabilizer. What thickness > do you think I would need and do they have it in small quantities? > Incidentally, how does one apply the stuff -- T88? Chuck > > ----- Original Message ----- > From: "KM Heide CPO/FAAOP" > To: > Sent: Friday, January 07, 2011 4:44 PM > Subject: Re: Pietenpol-List: Re: definition of UHMW for Ray > > > > > > > > > > I have plenty to go around if someone is looking for this material. We > > have a surplus store that purchased 100's of pounds of this stuff in all > > thicknesses. > > > > Ken Heide > > Fargo, ND > > > > > > --- On Fri, 1/7/11, DOMIT wrote: > > > >> From: DOMIT > >> Subject: Pietenpol-List: Re: definition of UHMW for Ray > >> To: pietenpol-list@matronics.com > >> Date: Friday, January 7, 2011, 11:33 AM > >> --> Pietenpol-List message posted > >> by: "DOMIT" > >> > >> Here is how you source this stuff easily: Go to > >> WalMart... or your local grocery store... or the dollar > >> store. Find cutting boards. That's the white > >> ones. > >> > >> -------- > >> Brad "DOMIT" Smith > >> > >> First rule of ground school: This is the ground... > >> don't hit it going fast. > >> > >> > >> > >> > >> Read this topic online here: > >> > >> http://forums.matronics.com/viewtopic.php?p=325911#325911 > >> > >> > >> > >> > >> > >> > >> > >> Email Forum - > >> FAQ, > >> - MATRONICS WEB FORUMS - > >> List Contribution Web Site - > >> -Matt > >> Dralle, List Admin. > >> > >> > >> > >> > > > > > > > > > > > > > > > > > > > > ________________________________ Message 24 ____________________________________ Time: 06:58:35 PM PST US Subject: Pietenpol-List: Re: New List Member? From: "kevinpurtee" That made my day! do not archive -------- Kevin "Axel" Purtee NX899KP Austin/Georgetown, TX Read this topic online here: http://forums.matronics.com/viewtopic.php?p=325962#325962 ________________________________ Message 25 ____________________________________ Time: 07:04:52 PM PST US Subject: Pietenpol-List: Re: definition of UHMW for Ray From: "kevinpurtee" So Ken, how cold is it in Fargo right now?:D do not archive -------- Kevin "Axel" Purtee NX899KP Austin/Georgetown, TX Read this topic online here: http://forums.matronics.com/viewtopic.php?p=325963#325963 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message pietenpol-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Pietenpol-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/pietenpol-list Browse Digests http://www.matronics.com/digest/pietenpol-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.