Today's Message Index:
----------------------
1. 10:14 AM - Re: Tail Brace Wires--Again (dgaldrich)
2. 02:15 PM - Prop-carving CD, The All-Power Tool Method (helspersew@aol.com)
3. 04:04 PM - Straight axle dimensions (jim)
4. 04:55 PM - Re: Straight axle dimensions (Greg Cardinal)
5. 05:05 PM - Re: Straight axle dimensions (carson)
6. 09:52 PM - Re: Straight axle dimensions (jim)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Tail Brace Wires--Again |
Mike and Jerry win the prize for decoding what I'm trying to do since it wasn't
obvious as I reread my post. The swager that Mike pictured runs $6,000+++ but
the finished fittings are VERY nice. The down side is that you'd better measure
right the first time if you do swaged fitting on both ends. The up side
is that the decreased drag from having fewer thimbles out in the breeze should
gain you LOTS of extra speed!
Off to find a sailboat guy who works on smaller boats...
Thanks guys...
Dave
Do not archive
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=351330#351330
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Prop-carving CD, The All-Power Tool Method |
Hello Good People,
I was just informed, by one of the more distinguished members of our group,
that ACS is out-of-stock of this highly-popular informative essay. Can't i
magine why, but FYI this book can now be down-loaded as an e-book from Airc
raft Technical Book Co. http://www.actechbooks.com/products/act615/
Good project for the upcoming winter months. :O)
Dan Helsper
Puryear, TN
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Straight axle dimensions |
I'm about to order metal for the straight axle and spreader bars. I know
the ODs are 1.5 and .75 inches, but what is the wall thickness?
Thanks,
Jim
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Straight axle dimensions |
Per the Hoopman plans:
Spreader bars - 3/4" X .035
Axle - 1 1/2 X .109
Some people increase the axle to .120
Greg Cardinal
----- Original Message -----
From: jim
To: Piet list
Sent: Saturday, September 03, 2011 6:02 PM
Subject: Pietenpol-List: Straight axle dimensions
I'm about to order metal for the straight axle and spreader bars. I
know the ODs are 1.5 and .75 inches, but what is the wall thickness?
Thanks,
Jim
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Straight axle dimensions |
Hi Jim
When I was at that stage it was recommended to me by others on the list to use
the heavy gauge I went with 3mm I think about .125 but I will have a look tonight
to make sure if no one else has chimed in.
Carson
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=351345#351345
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Straight axle dimensions |
Thanks Greg!
Jim
----- Original Message -----
From: Greg Cardinal
To: pietenpol-list@matronics.com
Sent: Saturday, September 03, 2011 6:53 PM
Subject: Re: Pietenpol-List: Straight axle dimensions
Per the Hoopman plans:
Spreader bars - 3/4" X .035
Axle - 1 1/2 X .109
Some people increase the axle to .120
Greg Cardinal
----- Original Message -----
From: jim
To: Piet list
Sent: Saturday, September 03, 2011 6:02 PM
Subject: Pietenpol-List: Straight axle dimensions
I'm about to order metal for the straight axle and spreader bars. I
know the ODs are 1.5 and .75 inches, but what is the wall thickness?
Thanks,
Jim
href="http://www.matronics.com/Navigator?Pietenpol-List">http://www.mat
ronics.com/Navigator?Pietenpol-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/c
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|