Today's Message Index:
----------------------
1. 02:12 AM - Re: Re: Bronze-Brass Bearings (Clif Dawson)
2. 03:27 AM - Re: Powder Coat Supplier (Jack)
3. 04:58 AM - Re: Bronze-Brass Bearings (womenfly2)
4. 08:16 AM - Classic Aviation footage (TOM STINEMETZE)
5. 09:50 PM - Re: Powder Coat Supplier (Michael Groah)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bronze-Brass Bearings |
I've been replacing journal bearings for forty years.
It's been my experience and is industry practice to
heat the surounding metal to enlarge the hole.
Heating the bearing directly will enlarge the bearing
itself thus jamming it tighter.
If the bearing is small, od 1" or less, and accessible
from the other side, you can hammer it out with a
brass drift, carefully. Larger ones should be pulled
out with an "inside" puller.You can make one
yourself to fit the application with iron plumbing
parts, a long bolt and nut and a thick washer to fit
the bearing. The pipe and a cap form a recepticle
for the bearing to slide into.
Clif
Life is not a matter of holding good cards,
but rather, of playing a bad hand well!"
Robert Louis Stevenson
>
> The oiled bearings can be replaced by heating the bearing some and
> pressing them out.
>
> --------
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=362220#362220
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Powder Coat Supplier |
Hi Jim,
I have a sprayer; I'm searching for a very special color. I've tried paint
from Eastwood and NIC. Someone mentioned a supplier in the last two weeks I
had not tried.
Thanks!
Jack
DSM
NX1929T
_____
From: owner-pietenpol-list-server@matronics.com
[mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of
jim_markle@mindspring.com
Sent: Monday, January 02, 2012 7:48 PM
Subject: Re: Pietenpol-List: Powder Coat Supplier
I got my setup @ Eastwood.
Eastwood.com
JM
_____
From: "Jack" <jack@textors.com>
Sender: owner-pietenpol-list-server@matronics.com
ReplyTo: pietenpol-list@matronics.com
Subject: Pietenpol-List: Powder Coat Supplier
A few weeks ago someone mentioned a powder coat = supplier. I couldn't find
in the archive. Could you share = again?
Thanks,
Jack
DSM
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bronze-Brass Bearings |
... you heat the bearing to just soften the retaining compound, then press it out.
Sorry if I was not clear enough on that.
--------
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=362316#362316
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Classic Aviation footage |
Ladies and Gentlemen:
Just so I don't start out the year by gettng flamed for un-Pietenpolish
conduct, let me say that if you watch this classic aviation footage all
the way through you will find a "sort of" Pietenpol connection. Note in
particular the open cockpit and the use of a doorbell ringer that cost $2.
http://www.aircraftowner.com/videos/view/americas-first-jet-flight-october-
1942_1617.html
Stinemetze
N328X
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Powder Coat Supplier |
I'm not sure what was mentioned before but I've used Pendry powder coatings f
or my powder before. They have some variety of materials.
www.pendrypowdercoatings.com/
Mike Groah
Sent from my iPhone
On Jan 3, 2012, at 3:24 AM, "Jack" <jack@textors.com> wrote:
> Hi Jim,
> I have a sprayer; I=99m searching for a very special color. I
=99ve tried paint from Eastwood and NIC. Someone mentioned a supplier in th
e last two weeks I had not tried.
> Thanks!
> Jack
> DSM
> NX1929T
>
> From: owner-pietenpol-list-server@matronics.com [mailto:owner-pietenpol-li
st-server@matronics.com] On Behalf Of jim_markle@mindspring.com
> Sent: Monday, January 02, 2012 7:48 PM
> To: pietenpol-list@matronics.com
> Subject: Re: Pietenpol-List: Powder Coat Supplier
>
> I got my setup @ Eastwood.
>
> Eastwood.com
>
> JM
> From: "Jack" <jack@textors.com>
> Sender: owner-pietenpol-list-server@matronics.com
> Date: Mon, 2 Jan 2012 19:24:29 -0600
> To: <pietenpol-list@matronics.com>
> ReplyTo: pietenpol-list@matronics.com
> Subject: Pietenpol-List: Powder Coat Supplier
>
> A few weeks ago someone mentioned a powder coat = supplier. I couldn
=99t find in the archive. Could you share = again?
>
> Thanks,
>
> Jack
>
> DSM
>
>
>
==========================
=========
==========================
=========
==========================
=========
==========================
=========
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|