Today's Message Index:
----------------------
1. 05:13 AM - Re: aluminum struts (Bill Church)
2. 05:18 AM - Re: aluminum struts (Michael Perez)
3. 05:39 AM - Re: aluminum struts (Gerry Holland)
4. 06:25 AM - Re: aluminum struts (bradandlinda tds.net)
5. 06:29 AM - Re: aluminum struts (Michael Perez)
6. 01:36 PM - Re: aluminum struts (Dick N)
7. 06:12 PM - Re: aluminum struts (Larry V)
8. 07:27 PM - Re: Re: aluminum struts (Dick N)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
Larry,
Many builders have successfully used aluminum struts on their Pietenpols. There's
lots of discussion and info in the archives. The aluminum extrusions are definitely
less expensive than new 4130 streamline tubing, but different attachment
details need to be used, since welding aluminum can greatly reduce it's strength.
Bill C.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372326#372326
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
I am using aluminum on mine. I believe there are a few flying Pietenpols th
at use them as well.- The aluminum struts will save you some weight.
Here is where I bought them:
http://carlsonaircraft.com/struts.html
Michael Perez
=0APietenpol HINT Videos
=0AKaretaker Aero
=0Awww.karetakeraero.com
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
Michael Hi.
Regarding Aluminium against 4130 profile and strength.
Is their any rule of thumb about comparative strengths.
I would like to change my round 1/2" 4130 Jury Struts for streamlined and wondered
whether aluminium would be suitable.
Regards
Gerry
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
The pre war Aeronca Chiefs used alum struts, but they were wider than J-3
struts.
On Thu, May 3, 2012 at 7:38 AM, Gerry Holland <gholland@content-stream.co.uk
> wrote:
> gholland@content-stream.co.uk>
>
> Michael Hi.
> Regarding Aluminium against 4130 profile and strength.
> Is their any rule of thumb about comparative strengths.
> I would like to change my round 1/2" 4130 Jury Struts for streamlined and
> wondered whether aluminium would be suitable.
> Regards
> Gerry
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
Gerry, replacing round with streamline is a good idea. I can't comment on c
omparative strengths, however I will say that my jury struts will be stream
line aluminum.- I don't believe these small struts see much stress, but t
hose that know will chime in.
Michael Perez
=0APietenpol HINT Videos
=0AKaretaker Aero
=0Awww.karetakeraero.com
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
Hi Gerry
I have a set of Aluminum struts and jury struts, I picked them up from
Carlson Aircraft in East Palastine, Ohio. I also picked up aluminum ends
for the struts. I think the total for everything was about $700. It was
worth every penny. They are for my new Piet, under construction at this
point.
Dick N.
----- Original Message -----
From: "Gerry Holland" <gholland@content-stream.co.uk>
Sent: Thursday, May 03, 2012 7:38 AM
Subject: Re: Pietenpol-List: aluminum struts
<gholland@content-stream.co.uk>
Michael Hi.
Regarding Aluminium against 4130 profile and strength.
Is their any rule of thumb about comparative strengths.
I would like to change my round 1/2" 4130 Jury Struts for streamlined and
wondered whether aluminium would be suitable.
Regards
Gerry
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
Thanks everyone for your replies.
Dick I was wondering what size of aluminum struts you would recommend.
Larry V
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372377#372377
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: aluminum struts |
My struts are 2.44" x 1.00". See them at carlsonaircraft.com .The struts
are actually pretty cheap $63 each, its the fitting that are pretty
expensive. I am going to polish mine and try to make them look like chrome.
Dick N
----- Original Message -----
From: "Larry V" <larryvangerven@hotmail.com>
Sent: Thursday, May 03, 2012 8:11 PM
Subject: Pietenpol-List: Re: aluminum struts
> <larryvangerven@hotmail.com>
>
> Thanks everyone for your replies.
> Dick I was wondering what size of aluminum struts you would recommend.
> Larry V
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=372377#372377
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|