Today's Message Index:
----------------------
1. 04:17 AM - Board stretcher (helspersew@aol.com)
2. 04:29 AM - Re: Board stretcher (womenfly2)
3. 05:10 AM - Re: turnbuckle size (Michael Perez)
4. 05:23 AM - Re: Board stretcher (tools)
5. 06:12 AM - Re: Re: Board stretcher (Michael Perez)
6. 08:06 AM - Re: ShortCut (K5YAC)
7. 08:44 AM - Cone Gear for Magneto (tkreiner)
8. 07:45 PM - Re: Re: Board stretcher (Clif Dawson)
9. 09:07 PM - Re: ShortCut (K5YAC)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
C'mon Cliff, this had GOT to be a hoax!
Dan Helsper
Puryear, TN
do not archive
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Board stretcher |
Really! ... I hope no one believed this, note the date posted, April 1st, 2012.
Good one!
--------
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372681#372681
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: turnbuckle size |
Larry, the -32L body, the "L" indicates it is a long body as opposed to the
short body, -32S.
The forks and the eyes can also be odered long. If the LAST letter for each
is the letter "L", they are long as well. Next to last letters indicate th
read direction.-- -32LL left head thread, long. -32RL, right hand threa
d, long.- -32 RS, right hand thread, short.
Michael Perez
=0APietenpol HINT Videos
=0AKaretaker Aero
=0Awww.karetakeraero.com
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Board stretcher |
Obviously fake... to go from 4 to 5 feet is NOT 20 percent like he says...
However, if you read the comments, and look carefully, you'll see it's a knot remover
as well. THAT could be useful. I imagine once stretched, the grain runout
would be less as well. Lastly, if longer, but cross section dimensionally
the same, it should weigh less per cubic volume, making it lighter and our planes
will climb better!
Seriously, this stuff has all kinds of uses!
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372684#372684
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Board stretcher |
I agree! Since I am building the short fuselage, if later in time, (during
a re-cover perhaps), I can put some of this "pancake" mix on the wood and s
tretch out the fuse to the long version...or more!- Fuselage too narrow?
Stretch it! Make it a two place side by side...or...
Do Not Archive
Michael Perez
=0APietenpol HINT Videos
=0AKaretaker Aero
=0Awww.karetakeraero.com
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Clif:
Do you know if that stuff works equally well on all types of wood? I'm wondering
if I were to apply it to my wings if the spruce, birch and mahogany would all
stretch equally. Seems like a good way to add 6' to the wings once they are
fully constructed. rather than pulling with a simple come-along, I figure I
could use a couple of trees tied to the root corners and pull on the wing tip
bow with a Bobcat or something.
--------
Mark Chouinard
Wings, Center Section and Empannage and Fuse framed up - Working on Landing Gear
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372690#372690
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Cone Gear for Magneto |
Hey gang,
I'm looking for a 1 3/4 inch long cone gear to fit an older Bendix magneto (SF4RN8),
or a complete SF4RN8 core with gear. Hit me offline if you have one.
Thanks,
--------
Tom Kreiner
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372692#372692
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Board stretcher |
Sometimes I just can't help myself!
And my kids are three thousand miles away
so they can't help me either! :-)
Anyway, here's the other end of my brake
system. Finally!!
Clif
"Beware of geeks bearing formulas." (Warren Buffett)
>
> Obviously fake... to go from 4 to 5 feet is NOT 20 percent like he says...
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I couldn't lure anyone in? I tried to sound like I was buying it... guess it didn't
work. Slow day...
--------
Mark Chouinard
Wings, Center Section and Empannage and Fuse framed up - Working on Landing Gear
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=372725#372725
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|