Today's Message Index:
----------------------
1. 12:13 AM - Re: Routing the tail pieces - table saw modified to router table (Minerjoe)
2. 09:48 AM - Re: End of an era... (Jim Boyer)
3. 01:38 PM - Re: Need email (macz@peak.org)
4. 06:04 PM - Re: Re: Routing the tail pieces - table saw modified to router table (Rick Holland)
5. 10:46 PM - tailplane weights... (aerocarjake)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Routing the tail pieces - table saw modified to router |
table
Nice, how heavy does your tailplane weigh? :D
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=408571#408571
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: End of an era... |
Graham,
Thanks for the gr eat message; I hope to enjoy my PIet as much.
Cheers,
Jim
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Dan--
Ernie is at ewmoreno@minetfiber.com
--Mac in Oregon
>
> Anybody know Ernie Moreno's email?
>
> Dan Helsper
> Puryear, TN
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Routing the tail pieces - table saw modified |
to router table
FYI, my uncovered tail components eneded up:
Fin - 2 1/4
Rudder - 3
Flippers - 2 1/3 each
Stab - 6 1/2
On Sat, Sep 14, 2013 at 1:13 AM, Minerjoe <j-s-mine@bendigo.net.au> wrote:
>
> Nice, how heavy does your tailplane weigh? :D
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=408571#408571
>
>
--
Rick Holland
Castle Rock, Colorado
NX6819Z
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | tailplane weights... |
Hello good Piet-ple...
While my tail parts are not fully completed (a few small plywood pad-ups to go),
I was asked to post the weights. So here we go....
Horiz stab. 5lb, 10.6oz
Right elev. 2lb, 0.8oz
Left elev. 1lb, 10.8oz
Rudder. 1lb, 15.2oz
Vert stab. 1lb, 2.4oz
Not sure why the L&R elevators are so different...? I did not build these parts
but have fine tuned them and routered/rounded the edges. Next I will use a jig
I just completed to rout the pockets for Vi Kap aluminum hinges.....
Had a very relaxing/productive day in the shop.....
--------
Jake Schultz - curator,
Newport Way Air Museum (OK, it's just my home)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=408605#408605
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|