Today's Message Index:
----------------------
1. 08:00 AM - Recent visits. (dfwplt)
2. 01:24 PM - Jeepenpol progress (aviken)
3. 03:32 PM - Shop Press Dies on eBay (jarheadpilot82)
4. 03:33 PM - Shop Press Dies on eBay (jarheadpilot82)
5. 03:34 PM - Shop Press Dies on eBay (jarheadpilot82)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I had the honor of two visits with Pietenpol builders while working in the Charlotte
NC area recently. Here are some pictures from my visit with Don Youngblood.
He is building a VERY close to plans Pietenpol Air Camper near Greenville,
SC. And it's going to be a nice one! Don is retired and gets to work on it a
LOT. In fact, every time I called before my visit he was in the garage working
on it!
I wish I had visited him a few years ago, he did a couple little things I SHOULD
have done! Oh well.
Getting to meet Don (and Chuck Campbell the week before) was a real pleasure.
Jim in Pryor....where my visit with Don resulted in me being motivated to put the
final topcoat on the bottom of my first wing panel....one more topcoat on the
top and the FINAL wing panel moves into the (heated) garage! Thanks for the
motivation Don!
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=438881#438881
Attachments:
http://forums.matronics.com//files/don6_186.jpg
http://forums.matronics.com//files/don5_749.jpg
http://forums.matronics.com//files/don4_598.jpg
http://forums.matronics.com//files/don3_175.jpg
http://forums.matronics.com//files/don2_104.jpg
http://forums.matronics.com//files/don1_108.jpg
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Jeepenpol progress |
I finished the silver coats of dope today and will soon move this fuselage to my
hanger to finish paint and assembly. I need to free up the space in my small
workshop so I can begin to assemble my wings...
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=438891#438891
Attachments:
http://forums.matronics.com//files/left_side_silver_fuselage_817.jpg
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Shop Press Dies on eBay |
I came across this eBay listing and contacted the guy. He is looking for me a punch
and vee die along with an additional gooseneck to use-
http://www.ebay.com/itm/111569842812?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Basically, he sells you a 3 inch to 5 inch section (but can sell you longer pieces
as needed) of each punch and die that you order from him. I will let you know
how it works out, but I emailed him and he seemed to be on the up and up.
It might be a good source for dies for the small amount of metal work needed for
building a Pietenpol. I have attached a screenshot of the listing for you to
get a quick look, and you can click on the link if you have further interest.
Hope it helps someone.
--------
Semper Fi,
Terry Hand
Athens, GA
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=438892#438892
Attachments:
http://forums.matronics.com//files/ebay_dies_for_sale_548.jpg
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Shop Press Dies on eBay |
I came across this eBay listing and contacted the guy. He is looking for me a punch
and vee die along with an additional gooseneck to use-
http://www.ebay.com/itm/111569842812?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Basically, he sells you a 3 inch to 5 inch section (but can sell you longer pieces
as needed) of each punch and die that you order from him. I will let you know
how it works out, but I emailed him and he seemed to be on the up and up.
It might be a good source for dies for the small amount of metal work needed for
building a Pietenpol. I have attached a screenshot of the listing for you to
get a quick look, and you can click on the link if you have further interest.
Hope it helps someone.
--------
Semper Fi,
Terry Hand
Athens, GA
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=438893#438893
Attachments:
http://forums.matronics.com//files/ebay_dies_for_sale_548.jpg
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Shop Press Dies on eBay |
I came across this eBay listing and contacted the guy. He is looking for me a punch
and vee die along with an additional gooseneck to use-
http://www.ebay.com/itm/111569842812?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Basically, he sells you a 3 inch to 5 inch section (but can sell you longer pieces
as needed) of each punch and die that you order from him. I will let you know
how it works out, but I emailed him and he seemed to be on the up and up.
It might be a good source for dies for the small amount of metal work needed for
building a Pietenpol. I have attached a screenshot of the listing for you to
get a quick look, and you can click on the link if you have further interest.
Hope it helps someone.
--------
Semper Fi,
Terry Hand
Athens, GA
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=438894#438894
Attachments:
http://forums.matronics.com//files/ebay_dies_for_sale_548.jpg
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|