Today's Message Index:
----------------------
1. 04:30 AM - Fw: Better, the enemy of great! (Steven Dortch)
2. 12:22 PM - Fuel tank - feels like I'm building an RV-7 ! (aerocarjake)
3. 01:01 PM - Re: Fuel tank - feels like I'm building an RV-7 ! (Greg Bacon)
4. 02:15 PM - Re: Fuel tank - feels like I'm building an RV-7 ! (aerocarjake)
5. 05:01 PM - Re: Re: Fuel tank - feels like I'm building an RV-7 ! (THOMAS.233327)
6. 05:01 PM - Re: Re: Fuel tank - feels like I'm building an RV-7 ! (CatDesigns)
7. 07:54 PM - Re: Fuel tank - feels like I'm building an RV-7 ! (Ray Krause)
8. 10:56 PM - Re: Fw: Better, the enemy of great! (biplan53)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Fwd: Better, the enemy of great! |
Yesterday, I had my wing gas tank cover out in the yard to paint. Rattle
can red. First coat was perfect!
Then I thought I would add one more light coat. Oh No a run. well I will
try to wipe it of with a smooth rag with acetone. Now it is even worse. So
I end up sanding it and finally repainting it, It is not near as nice as
the first coat. But it is OK. I will not mess with it until some time long
after the plane is flying.
Sound's like the story of my life.
--
Blue Skies,
Steve D
--
Blue Skies,
Steve D
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Fuel tank - feels like I'm building an RV-7 ! |
Hello good Piet-ple,
A quick update on my project.
Been working on the fuel tank lately - only one tank that will sit in the wing
center-section. After a couple false starts it's finally starting to come together.
I'm making the tank out of 0.063 5052 sheet so it feels like I'm building
the wing to an RV-7....! (So much for a steel-tube, wood and fabric airplane...!!)
The current plan is for the internal grid to be rivited to itself and the external
seems to be fully welded - similar in construction to the Stearman.
Hope you all are enjoying spring...!
--------
Jake Schultz - curator,
Newport Way Air Museum (OK, it's just my home)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=439203#439203
Attachments:
http://forums.matronics.com//files/4_practice_rib_492.jpg
http://forums.matronics.com//files/3_bent_flange_184.jpg
http://forums.matronics.com//files/2_bending_flange_589.jpg
http://forums.matronics.com//files/1_fuel_tank_in_work_808.jpg
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel tank - feels like I'm building an RV-7 ! |
Looks great Jake!
Are you incorporating a low spot to keep water from accumulating? How wide
is your center section?
On Mon, Mar 9, 2015 at 1:22 PM, aerocarjake <flight.jake@gmail.com> wrote:
> >
>
> Hello good Piet-ple,
>
> A quick update on my project.
>
> Been working on the fuel tank lately - only one tank that will sit in the
> wing center-section. After a couple false starts it's finally starting to
> come together. I'm making the tank out of 0.063 5052 sheet so it feels like
> I'm building the wing to an RV-7....! (So much for a steel-tube, wood and
> fabric airplane...!!)
>
> The current plan is for the internal grid to be rivited to itself and the
> external seems to be fully welded - similar in construction to the Stearman.
>
> Hope you all are enjoying spring...!
>
> --------
> Jake Schultz - curator,
> Newport Way Air Museum (OK, it's just my home)
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=439203#439203
>
>
> Attachments:
>
> http://forums.matronics.com//files/4_practice_rib_492.jpg
> http://forums.matronics.com//files/3_bent_flange_184.jpg
> http://forums.matronics.com//files/2_bending_flange_589.jpg
> http://forums.matronics.com//files/1_fuel_tank_in_work_808.jpg
>
>
--
Greg Bacon
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel tank - feels like I'm building an RV-7 ! |
Thx...
Yes I am installing two Stearman sumps in the aft corners of the tank.
My center-section is 48" wide. That is wider than plans so I can accommodate just
one tank an have enough capacity for my thirsty engine.
This tank SHOULD be about 18 gallons (by calculation) so with my ROTEC engine burning
about 6gph I should have 2 1/2 hours + the 30 minute reserve.
--------
Jake Schultz - curator,
Newport Way Air Museum (OK, it's just my home)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=439206#439206
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel tank - feels like I'm building an RV-7 ! |
Jake!
It looks like you are installing the ends of your tank backwords! The weld is best
done from the edge of one sheet to the outside radius of the other. Call me
and I'll run up there and see your project.
I learned about that welding tip when I was building the Hummel Bird tanks (3 of
them). It easier by far the have the ends of the top, bottom, front and back
weld the edge of one sheet to the outside bend on the ends than it is to weld
along the edges of two sheets that are lapped. Also, if you swap the ends of
your tank so there is no flange on the finished tank, you'll have room for more
gas.
When is the next 441 meeting?
Tom Hale- (253) two-three-six--eight three two two
Still not building my Sonex kit-but that will change soon! (New wife wants to build
and airplane)
----- Original Message -----
From: "aerocarjake" <flight.jake@gmail.com>
Sent: Monday, March 9, 2015 2:15:06 PM
Subject: Pietenpol-List: Re: Fuel tank - feels like I'm building an RV-7 !
Thx...
Yes I am installing two Stearman sumps in the aft corners of the tank.
My center-section is 48" wide. That is wider than plans so I can accommodate just
one tank an have enough capacity for my thirsty engine.
This tank SHOULD be about 18 gallons (by calculation) so with my ROTEC engine burning
about 6gph I should have 2 1/2 hours + the 30 minute reserve.
--------
Jake Schultz - curator,
Newport Way Air Museum (OK, it's just my home)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=439206#439206
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel tank - feels like I'm building an RV-7 ! |
Jake
When you say Stearman sumps do you mean the Stearman type fuel gage or is
there an actual bump in the bottom of the tank?
Chris
Sacramento, CA
WestcoastPiet.com
-----Original Message-----
From: owner-pietenpol-list-server@matronics.com
[mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of aerocarjake
Sent: Monday, March 9, 2015 2:15 PM
Subject: Pietenpol-List: Re: Fuel tank - feels like I'm building an RV-7 !
--> <flight.jake@gmail.com>
Thx...
Yes I am installing two Stearman sumps in the aft corners of the tank.
My center-section is 48" wide. That is wider than plans so I can accommodate
just one tank an have enough capacity for my thirsty engine.
This tank SHOULD be about 18 gallons (by calculation) so with my ROTEC
engine burning about 6gph I should have 2 1/2 hours + the 30 minute reserve.
--------
Jake Schultz - curator,
Newport Way Air Museum (OK, it's just my home)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=439206#439206
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel tank - feels like I'm building an RV-7 ! |
Jake,
Sure looks great! This will be one of the most perfect Piets around. Congratulations.
Ray Krause
Building SkyScout
Sent from my iPad
> On Mar 9, 2015, at 12:22 PM, aerocarjake <flight.jake@gmail.com> wrote:
>
>
> Hello good Piet-ple,
>
> A quick update on my project.
>
> Been working on the fuel tank lately - only one tank that will sit in the wing
center-section. After a couple false starts it's finally starting to come together.
I'm making the tank out of 0.063 5052 sheet so it feels like I'm building
the wing to an RV-7....! (So much for a steel-tube, wood and fabric airplane...!!)
>
> The current plan is for the internal grid to be rivited to itself and the external
seems to be fully welded - similar in construction to the Stearman.
>
> Hope you all are enjoying spring...!
>
> --------
> Jake Schultz - curator,
> Newport Way Air Museum (OK, it's just my home)
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=439203#439203
>
>
>
>
> Attachments:
>
> http://forums.matronics.com//files/4_practice_rib_492.jpg
> http://forums.matronics.com//files/3_bent_flange_184.jpg
> http://forums.matronics.com//files/2_bending_flange_589.jpg
> http://forums.matronics.com//files/1_fuel_tank_in_work_808.jpg
>
>
>
>
>
>
>
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fwd: Better, the enemy of great! |
Steven don't feel bad I can't stop that temptation to add just a little more either.
In my 38 years of repairing telephone cables I think over half of them were
cut because the machine operator wanted to make just one more swipe with the
back hoe.
--------
Building steel fuselage aircamper.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=439218#439218
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|