---------------------------------------------------------- Pietenpol-List Digest Archive --- Total Messages Posted Tue 07/14/15: 8 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:21 AM - Re: Chatt to brodhead thurs, fri (Jack) 2. 05:34 AM - Re: Board feet of lumber (Bill Church) 3. 05:42 AM - Re: Board feet of lumber (tools) 4. 05:44 AM - Re: Chatt to brodhead thurs, fri (tools) 5. 05:52 AM - Re: Board feet of lumber (bdewenter) 6. 07:57 AM - Revised Brodhead Forum Schedule for Saturday (John Hofmann) 7. 09:47 AM - Anyone coming from St. Louis? (tools) 8. 05:47 PM - Re: Board feet of lumber (jarheadpilot82) ________________________________ Message 1 _____________________________________ Time: 03:21:19 AM PST US Subject: Re: Pietenpol-List: Chatt to brodhead thurs, fri From: Jack Tools you going to make Brodhead? If so please come for a Brat Friday at 11:30, SE corner of the field. Sent from my iPad Jack Textor > On Jul 13, 2015, at 4:33 PM, "tools" wrote: > > > Anyone else along that route about that time? If weather cooperates, planning on overnighting in rantoul. > > General route > > 9a5 m54 jqd siv tip > > Tip rpj c37 > > Cheers! > > Tools 423 580 1383 > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=444706#444706 > > > > > > > > > > ________________________________ Message 2 _____________________________________ Time: 05:34:28 AM PST US Subject: Pietenpol-List: Re: Board feet of lumber From: "Bill Church" Terry Hand, This does not change anything you said, but to be correct, one board at 2" (or 8/4) X 6" X 20' is 20 board feet, so 2 boards would be 40 board feet. > I have used 2 rough sawn planks 2" x 6" @ 20 ft long - that's 40 board feet :) Bill C. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=444732#444732 ________________________________ Message 3 _____________________________________ Time: 05:42:49 AM PST US Subject: Pietenpol-List: Re: Board feet of lumber From: "tools" By the way, somewhat rare, mccormicks has 5/4 spruce, which yields one inch quite efficiently. If you're getting custom sawed, might want to consider that. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=444733#444733 ________________________________ Message 4 _____________________________________ Time: 05:44:27 AM PST US Subject: Pietenpol-List: Re: Chatt to brodhead thurs, fri From: "tools" Trying to get in about then... Hold back a couple if we are late! Save a spot, we will just taxi up! Thanks! Tools Read this topic online here: http://forums.matronics.com/viewtopic.php?p=444734#444734 ________________________________ Message 5 _____________________________________ Time: 05:52:40 AM PST US Subject: Pietenpol-List: Re: Board feet of lumber From: "bdewenter" Andy Garrett wrote: > > > I'll study some planes, take plenty of pictures, and talk to some folks at Oshkosh before I decide which path I wind up taking for spars. > > Thanks fellas! Andy, A few of us are using extruded aluminum spars. I am using the FC-10 standard piet wing design. I purchased item 4-A from Carlson Aircraft. Terry Hand built Ribblet so his spars are a little taller than mine and he is a tad ahead of me. Bob -------- Bob 'Early Builder' Dewenter Dayton OH Read this topic online here: http://forums.matronics.com/viewtopic.php?p=444737#444737 ________________________________ Message 6 _____________________________________ Time: 07:57:58 AM PST US From: John Hofmann Subject: Pietenpol-List: Revised Brodhead Forum Schedule for Saturday 2015 FORUM SCHEDULE 10 11:00 Pietenpol Sheet Metal Ken Perkins 11 12:00 Hope & Change Gone Bad Jack Phillips 1 2:30 Model A Fords Ken Perkins 2:45 4:15 Corvair Engines William Wynne Best, -john- ________________________________ Message 7 _____________________________________ Time: 09:47:38 AM PST US Subject: Pietenpol-List: Anyone coming from St. Louis? From: "tools" I gotta coupla bottles I need picked up from the Distillery 630 downtown... Tools 423 580 1383 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=444752#444752 ________________________________ Message 8 _____________________________________ Time: 05:47:53 PM PST US Subject: Pietenpol-List: Re: Board feet of lumber From: "jarheadpilot82" Bill, I obviously missed the two planks. My mistake. -------- Semper Fi, Terry Hand Athens, GA Read this topic online here: http://forums.matronics.com/viewtopic.php?p=444771#444771 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message pietenpol-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Pietenpol-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/pietenpol-list Browse Digests http://www.matronics.com/digest/pietenpol-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.