Today's Message Index:
----------------------
1. 06:54 AM - gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) (Hyvris (Petr Ludera))
2. 08:31 AM - Re: gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) (larharris2 Harris)
3. 10:01 AM - Re: gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) (vic groah)
4. 10:20 AM - Re: gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) (Ray Krause)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) |
Hello everyone,
this is my first post to the list, Im Pietenpol builder from Czech republic
(central europe). This list is so perfect, too much informations at one
place!
I have a little problem. Now i start to build empenage sections. Just
drawed full scale plans. And now my question. Which orientation of grain at
gussets on empenage is correct? In original plans i didnt find any word
about it... At attachment is part of original plans, if someone could draw
the grain directions i will be very happy :-))
Thanks a lot,
Petr Ludera
Czech republic
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) |
Welcome=2C Petr.
Maybe others will disagree=2C but I did not care about direction of grain i
n the gussets. Gusset material is plywood. Interior layers of the ply will
have grain direction 90 degrees to the surface ply. I tried to cut my gusse
ts to make the best use of my material=2C with the least waste.
Lorenzo
Subject: Pietenpol-List: gussets grain orientation - empenage (rudder=2Cfin
=2Celevator=2Cstabilizator)
From: hyvris@gmail.com
Hello everyone=2C
this is my first post to the list=2C Im Pietenpol builder from Czech republ
ic (central europe). This list is so perfect=2C too much informations at on
e place!
I have a little problem. Now i start to build empenage sections. Just drawe
d full scale plans. And now my question. Which orientation of grain at guss
ets on empenage is correct? In original plans i didnt find any word about i
t... At attachment is part of original plans=2C if someone could draw the g
rain directions i will be very happy :-))
Thanks a lot=2C
Petr Ludera
Czech republic
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) |
I agree with Lorenzo, the gain orientation is not a major issue with ply,
You are to be complimented on your care for doing things correctly. Keep
up the good work. Vic
On Sat, Jan 23, 2016 at 8:29 AM, larharris2 Harris <larharris2@msn.com>
wrote:
> Welcome, Petr.
> Maybe others will disagree, but I did not care about direction of grain in
> the gussets. Gusset material is plywood. Interior layers of the ply will
> have grain direction 90 degrees to the surface ply. I tried to cut my
> gussets to make the best use of my material, with the least waste.
>
> Lorenzo
>
>
> ------------------------------
> Date: Sat, 23 Jan 2016 15:34:14 +0100
> Subject: Pietenpol-List: gussets grain orientation - empenage
> (rudder,fin,elevator,stabilizator)
> From: hyvris@gmail.com
> To: pietenpol-list@matronics.com
>
>
> Hello everyone,
>
> this is my first post to the list, Im Pietenpol builder from Czech
> republic (central europe). This list is so perfect, too much informations
> at one place!
>
>
> I have a little problem. Now i start to build empenage sections. Just
> drawed full scale plans. And now my question. Which orientation of grain at
> gussets on empenage is correct? In original plans i didnt find any word
> about it... At attachment is part of original plans, if someone could draw
> the grain directions i will be very happy :-))
>
>
> Thanks a lot,
> Petr Ludera
> Czech republic
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: gussets grain orientation - empenage (rudder,fin,elevator,stabilizator) |
I did the same. Just use good aircraft/marine three ply plywood and cut with
out regard for the grain. Life is simple!
Ray Krause
Building SkyScout
Sent from my iPad
> On Jan 23, 2016, at 8:29 AM, larharris2 Harris <larharris2@msn.com> wrote:
>
> Welcome, Petr.
> Maybe others will disagree, but I did not care about direction of grain in
the gussets. Gusset material is plywood. Interior layers of the ply will ha
ve grain direction 90 degrees to the surface ply. I tried to cut my gussets t
o make the best use of my material, with the least waste.
>
> Lorenzo
>
>
> Date: Sat, 23 Jan 2016 15:34:14 +0100
> Subject: Pietenpol-List: gussets grain orientation - empenage (rudder,fin,
elevator,stabilizator)
> From: hyvris@gmail.com
> To: pietenpol-list@matronics.com
>
> Hello everyone,
>
> this is my first post to the list, Im Pietenpol builder from Czech republi
c (central europe). This list is so perfect, too much informations at one pl
ace!
>
>
> I have a little problem. Now i start to build empenage sections. Just draw
ed full scale plans. And now my question. Which orientation of grain at guss
ets on empenage is correct? In original plans i didnt find any word about it
... At attachment is part of original plans, if someone could draw the grain
directions i will be very happy :-))
>
>
> Thanks a lot,
> Petr Ludera
> Czech republic
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|