Today's Message Index:
----------------------
1. 05:00 AM - rudder cables (Ralph)
2. 06:07 AM - Re: Favor (AircamperN11MS)
3. 06:07 AM - Re: Re: rudder cables and tape (Jack Textor)
4. 08:12 AM - Re: Re: rudder cables and tape and now trim (Steven Dortch)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Thanks for the responses to my rudder cable questions. My taping the
cross cables question wasn=99t very clear. I was thinking of the
drag/antidrag cables inside the wing and the cross cables on the wing
struts. I am currently fitting the jury struts brackets on the spars
and then hope to start covering the wings.
Ralph
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
I see it Jerry
--------
Scott Liefeld
Flying N11MS since March 1972
Steel Tube
C-85-12
Wire Wheels
Brodhead in 1996
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=456057#456057
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: rudder cables and tape |
Thanks Oscar!
-----Original Message-----
From: owner-pietenpol-list-server@matronics.com
[mailto:owner-pietenpol-list-server@matronics.com] On Behalf Of taildrags
Sent: Monday, May 09, 2016 11:58 PM
Subject: Pietenpol-List: Re: rudder cables and tape
--> <taildrags@hotmail.com>
You builders who are working out your rudder and tailwheel cable routing are
going to hear an echo here, but "check out Westcoastpiet"!! It's a treasure
chest of information! Take twenty minutes and just click on the photo links
of any of the Piets listed there, and you will find all you're looking
for... and more. Much more.
I'll throw in just one image, from my own airplane, of the view from the
pilot's seat back into the tailcone:
http://www.flysquirrel.net/piets/trim02.jpg
I know it's fuzzy, and ignore the green bungee that serves as elevator trim,
but the point is that the rudder cables turn up after leaving the back of
the seat (on NX41CC there are both Formica and nylon fairleads till the
cables exit the tail fabric). For the tailwheel cables, there are nylon
fairleads along the lower longeron x-members until the cables exit the tail
fabric. Bear in mind that you will NEVER be able to reach back there to get
to those fairleads, whether or not you have a belly access plate, so do it
right the first time (preferably before covering), and you'll never have to
worry about it again.
--------
Oscar Zuniga
Medford, OR
Air Camper NX41CC "Scout"
A75 power
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=456047#456047
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: rudder cables and tape and now trim |
Oscar, your trim looks simple. But I don't understand the pulley. How do
you adjust the trim?
Blue skies,
Steve D
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|