Today's Message Index:
----------------------
 
     1. 05:47 AM - Re: Working with sheet metal (echobravo4)
     2. 06:42 AM - Re: Working with sheet metal (Pocono John)
     3. 06:45 AM - Re: Dick Navratil's Rotec powered Piet (charles mcfarland)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:47:27 AM PST US
Subject: 
Re: Working with sheet metal
From: 
"echobravo4" <eab4@comcast.net>
      
      
      Hi John
      
      i cut out the blanks with a metal cutting bandsaw-
      get the shapes close with the grinder, then draw file the edges and finish
      with fine grade wet or dry sandpaper
      
      --------
      Earl Brown
      
      I may not have gone where I intended to go, but I think I have ended up where I
      intended to be.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=470987#470987
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:42:46 AM PST US
Subject: 
Re: Working with sheet metal
From: 
"Pocono John" <tinmotion@yahoo.com>
      
      
      Thank you Tom , Bob and Earl. Got it.
      
      JC
      
      --------
      John Cronin
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=470988#470988
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:45:26 AM PST US
Subject: 
Re: Dick Navratil's Rotec powered Piet
From: 
"charles mcfarland" <charles.w.mcfarland@gmail.com>
      
      
      Hi Dale,
      
      Thanks for the reply and info.  I think you are talking about Aircraft Spruce when
      you said AC&S?  I can send them a sample.  I have had lots of help thanks
      to the forum and think there is a good possibility I can get a close match by
      using one of several suggested techniques along with some trial and error work
      on some junk pieces.
      
      I will also try to call Aircraft Spruce just to see if they might have a record
      of what Dick may have ordered years ago.  Probably a long shot, but you never
      know.
      
      Looking forward to Brodhead!
      
      Charlie
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=470989#470989
      
      








Other Matronics Email List Services




Post A New Message
  
pietenpol-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Pietenpol-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/pietenpol-list
Browse Pietenpol-List Digests
  
http://www.matronics.com/digest/pietenpol-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --