---------------------------------------------------------- Pietenpol-List Digest Archive --- Total Messages Posted Sat 07/15/17: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:18 PM - Brodhead (dndboyd2@gmail.com) 2. 05:18 PM - Brodhead (dndboyd2@gmail.com) 3. 05:38 PM - Re: Brodhead (Jack Textor) ________________________________ Message 1 _____________________________________ Time: 05:18:13 PM PST US From: dndboyd2@gmail.com Subject: Pietenpol-List: Brodhead I haven't seen anything about the Brodhead fly-in. Is it still on? Sent from my iPhone > On Jul 15, 2017, at 2:03 AM, Pietenpol-List Digest Server wrote: > > * > > ================================================= > Online Versions of Today's List Digest Archive > ================================================= > > Today's complete Pietenpol-List Digest can also be found in either of the > two Web Links listed below. The .html file includes the Digest formatted > in HTML for viewing with a web browser and features Hyperlinked Indexes > and Message Navigation. The .txt file includes the plain ASCII version > of the Pietenpol-List Digest and can be viewed with a generic text editor > such as Notepad or with a web browser. > > HTML Version: > > http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter 17-07-14&Archive=Pietenpol > > Text Version: > > http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter 17-07-14&Archive=Pietenpol > > > =============================================== > EMail Version of Today's List Digest Archive > =============================================== > > > ---------------------------------------------------------- > Pietenpol-List Digest Archive > --- > Total Messages Posted Fri 07/14/17: 3 > ---------------------------------------------------------- > > > Today's Message Index: > ---------------------- > > 1. 05:47 AM - Re: Working with sheet metal (echobravo4) > 2. 06:42 AM - Re: Working with sheet metal (Pocono John) > 3. 06:45 AM - Re: Dick Navratil's Rotec powered Piet (charles mcfarland) > > > > ________________________________ Message 1 _____________________________________ > > > Time: 05:47:27 AM PST US > Subject: Pietenpol-List: Re: Working with sheet metal > From: "echobravo4" > > > Hi John > > i cut out the blanks with a metal cutting bandsaw- > get the shapes close with the grinder, then draw file the edges and finish > with fine grade wet or dry sandpaper > > -------- > Earl Brown > > I may not have gone where I intended to go, but I think I have ended up where I > intended to be. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=470987#470987 > > > ________________________________ Message 2 _____________________________________ > > > Time: 06:42:46 AM PST US > Subject: Pietenpol-List: Re: Working with sheet metal > From: "Pocono John" > > > Thank you Tom , Bob and Earl. Got it. > > JC > > -------- > John Cronin > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=470988#470988 > > > ________________________________ Message 3 _____________________________________ > > > Time: 06:45:26 AM PST US > Subject: Pietenpol-List: Re: Dick Navratil's Rotec powered Piet > From: "charles mcfarland" > > > Hi Dale, > > Thanks for the reply and info. I think you are talking about Aircraft Spruce when > you said AC&S? I can send them a sample. I have had lots of help thanks > to the forum and think there is a good possibility I can get a close match by > using one of several suggested techniques along with some trial and error work > on some junk pieces. > > I will also try to call Aircraft Spruce just to see if they might have a record > of what Dick may have ordered years ago. Probably a long shot, but you never > know. > > Looking forward to Brodhead! > > Charlie > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=470989#470989 > > > > > > > > ________________________________ Message 2 _____________________________________ Time: 05:18:13 PM PST US From: dndboyd2@gmail.com Subject: Pietenpol-List: Brodhead I haven't seen anything about the Brodhead fly-in. Is it still on? Sent from my iPhone > On Jul 15, 2017, at 2:03 AM, Pietenpol-List Digest Server wrote: > > * > > ================================================= > Online Versions of Today's List Digest Archive > ================================================= > > Today's complete Pietenpol-List Digest can also be found in either of the > two Web Links listed below. The .html file includes the Digest formatted > in HTML for viewing with a web browser and features Hyperlinked Indexes > and Message Navigation. The .txt file includes the plain ASCII version > of the Pietenpol-List Digest and can be viewed with a generic text editor > such as Notepad or with a web browser. > > HTML Version: > > http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter 17-07-14&Archive=Pietenpol > > Text Version: > > http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter 17-07-14&Archive=Pietenpol > > > =============================================== > EMail Version of Today's List Digest Archive > =============================================== > > > ---------------------------------------------------------- > Pietenpol-List Digest Archive > --- > Total Messages Posted Fri 07/14/17: 3 > ---------------------------------------------------------- > > > Today's Message Index: > ---------------------- > > 1. 05:47 AM - Re: Working with sheet metal (echobravo4) > 2. 06:42 AM - Re: Working with sheet metal (Pocono John) > 3. 06:45 AM - Re: Dick Navratil's Rotec powered Piet (charles mcfarland) > > > > ________________________________ Message 1 _____________________________________ > > > Time: 05:47:27 AM PST US > Subject: Pietenpol-List: Re: Working with sheet metal > From: "echobravo4" > > > Hi John > > i cut out the blanks with a metal cutting bandsaw- > get the shapes close with the grinder, then draw file the edges and finish > with fine grade wet or dry sandpaper > > -------- > Earl Brown > > I may not have gone where I intended to go, but I think I have ended up where I > intended to be. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=470987#470987 > > > ________________________________ Message 2 _____________________________________ > > > Time: 06:42:46 AM PST US > Subject: Pietenpol-List: Re: Working with sheet metal > From: "Pocono John" > > > Thank you Tom , Bob and Earl. Got it. > > JC > > -------- > John Cronin > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=470988#470988 > > > ________________________________ Message 3 _____________________________________ > > > Time: 06:45:26 AM PST US > Subject: Pietenpol-List: Re: Dick Navratil's Rotec powered Piet > From: "charles mcfarland" > > > Hi Dale, > > Thanks for the reply and info. I think you are talking about Aircraft Spruce when > you said AC&S? I can send them a sample. I have had lots of help thanks > to the forum and think there is a good possibility I can get a close match by > using one of several suggested techniques along with some trial and error work > on some junk pieces. > > I will also try to call Aircraft Spruce just to see if they might have a record > of what Dick may have ordered years ago. Probably a long shot, but you never > know. > > Looking forward to Brodhead! > > Charlie > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=470989#470989 > > > > > > > > ________________________________ Message 3 _____________________________________ Time: 05:38:33 PM PST US From: Jack Textor Subject: Re: Pietenpol-List: Brodhead Yes... http://www.eaa431.org/ Jack Textor Sent from my iPad > On Jul 15, 2017, at 7:17 PM, dndboyd2@gmail.com wrote: > > > I haven't seen anything about the Brodhead fly-in. Is it still on? > > Sent from my iPhone > >> On Jul 15, 2017, at 2:03 AM, Pietenpol-List Digest Server wrote: >> >> * >> >> ========================= ======================== >> Online Versions of Today's List Digest Archive >> ========================= ======================== >> >> Today's complete Pietenpol-List Digest can also be found in either of the >> two Web Links listed below. The .html file includes the Digest formatted >> in HTML for viewing with a web browser and features Hyperlinked Indexes >> and Message Navigation. The .txt file includes the plain ASCII version >> of the Pietenpol-List Digest and can be viewed with a generic text editor >> such as Notepad or with a web browser. >> >> HTML Version: >> >> http://www.matronics.com/digest/digestview.php?Style=82701&View=htm l&Chapter 17-07-14&Archive=Pietenpol >> >> Text Version: >> >> http://www.matronics.com/digest/digestview.php?Style=82701&View=txt &Chapter 17-07-14&Archive=Pietenpol >> >> >> ========================= ====================== >> EMail Version of Today's List Digest Archive >> ========================= ====================== >> >> >> ---------------------------------------------------------- >> Pietenpol-List Digest Archive >> --- >> Total Messages Posted Fri 07/14/17: 3 >> ---------------------------------------------------------- >> >> >> Today's Message Index: >> ---------------------- >> >> 1. 05:47 AM - Re: Working with sheet metal (echobravo4) >> 2. 06:42 AM - Re: Working with sheet metal (Pocono John) >> 3. 06:45 AM - Re: Dick Navratil's Rotec powered Piet (charles mcfarla nd) >> >> >> >> ________________________________ Message 1 ____________________________ _________ >> >> >> Time: 05:47:27 AM PST US >> Subject: Pietenpol-List: Re: Working with sheet metal >> From: "echobravo4" >> >> >> Hi John >> >> i cut out the blanks with a metal cutting bandsaw- >> get the shapes close with the grinder, then draw file the edges and finis h >> with fine grade wet or dry sandpaper >> >> -------- >> Earl Brown >> >> I may not have gone where I intended to go, but I think I have ended up w here I >> intended to be. >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=470987#470987 >> >> >> ________________________________ Message 2 ____________________________ _________ >> >> >> Time: 06:42:46 AM PST US >> Subject: Pietenpol-List: Re: Working with sheet metal >> From: "Pocono John" >> >> >> Thank you Tom , Bob and Earl. Got it. >> >> JC >> >> -------- >> John Cronin >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=470988#470988 >> >> >> ________________________________ Message 3 ____________________________ _________ >> >> >> Time: 06:45:26 AM PST US >> Subject: Pietenpol-List: Re: Dick Navratil's Rotec powered Piet >> From: "charles mcfarland" >> >> >> Hi Dale, >> >> Thanks for the reply and info. I think you are talking about Aircraft Sp ruce when >> you said AC&S? I can send them a sample. I have had lots of help thanks >> to the forum and think there is a good possibility I can get a close matc h by >> using one of several suggested techniques along with some trial and error work >> on some junk pieces. >> >> I will also try to call Aircraft Spruce just to see if they might have a r ecord >> of what Dick may have ordered years ago. Probably a long shot, but you n ever >> know. >> >> Looking forward to Brodhead! >> >> Charlie >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=470989#470989 >> >> >> >> >> >> >> >> > ========================== ========= ========================== ========= ========================== ========= ========================== ========= ========================== ========= > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message pietenpol-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Pietenpol-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/pietenpol-list Browse Digests http://www.matronics.com/digest/pietenpol-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.