Today's Message Index:
----------------------
1. 10:49 AM - Flattening 1-3/8 diameter tubing on split gear (Harvey Plummer)
2. 04:39 PM - Re: Flattening 1-3/8 diameter tubing on split gear (Jack Textor)
3. 06:19 PM - Re: Flattening 1-3/8 diameter tubing on split gear (Catdesigns)
4. 06:27 PM - Re: Ragwing Ultra-Piet (cdlwingnut)
5. 08:03 PM - Re: Flattening 1-3/8 diameter tubing on split gear (Semih Oksay)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Flattening 1-3/8 diameter tubing on split gear |
How did those of you with a split gear flatten the ends of the 1-3/8" diameter
tubing? I do not have a press with which to do it.
--------
Harv, 485PB
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=479273#479273
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Flattening 1-3/8 diameter tubing on split gear |
Harv, I heated with a torch then squeezed in a vice. Worked well.
Jack Textor
Sent from my iPad
> On Apr 11, 2018, at 12:49 PM, Harvey Plummer <plummerharvey@yahoo.com> wrote:
>
>
> How did those of you with a split gear flatten the ends of the 1-3/8" diameter
> tubing? I do not have a press with which to do it.
>
> --------
> Harv, 485PB
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=479273#479273
>
>
>
>
>
>
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Flattening 1-3/8 diameter tubing on split gear |
This is how I did it (see attached). All it takes is a bench vice and heat. Makes
flattening really easy.
Chris
--------
Chris
Sacramento, CA
WestCoastPiet.com
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=479284#479284
Attachments:
http://forums.matronics.com//files/2012_2_22_130.pdf
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Ragwing Ultra-Piet |
After rechecking my plans and looking at pictures of other ultra piets the bottom
block is not angled down to be perbendicular to the ground. I may still consider
making mine so anyway though.
I have been working on my center supports some more though
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=479285#479285
Attachments:
http://forums.matronics.com//files/20180411_124324_resized_163.jpg
http://forums.matronics.com//files/20180411_124328_resized_182.jpg
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Flattening 1-3/8 diameter tubing on split gear |
A strong vice may work.
Semih=8B
On Thu, Apr 12, 2018 at 2:38 AM, Jack Textor <jack@textors.com> wrote:
>
> Harv, I heated with a torch then squeezed in a vice. Worked well.
>
> Jack Textor
>
> Sent from my iPad
>
> > On Apr 11, 2018, at 12:49 PM, Harvey Plummer <plummerharvey@yahoo.com>
> wrote:
> >
> plummerharvey@yahoo.com>
> >
> > How did those of you with a split gear flatten the ends of the 1-3/8"
> diameter
> > tubing? I do not have a press with which to do it.
> >
> > --------
> > Harv, 485PB
> >
> >
> >
> >
> > Read this topic online here:
> >
> > http://forums.matronics.com/viewtopic.php?p=479273#479273
> >
> >
> >
> >
> >
> >
> >
> >
> >
>
>
===========
===========
===========
===========
===========
>
>
--
Semih Oksay
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|