----------------------------------------------------------
                           Pietenpol-List Digest Archive
                                      ---
                     Total Messages Posted Wed 03/11/20: 2
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 01:55 PM - Re: Ragwing Ultra-Piet  (cdlwingnut)
     2. 04:00 PM - Re: Re: Ragwing Ultra-Piet  (Glen Schweizer)
 
 
 
________________________________  Message 1  _____________________________________


Time: 01:55:00 PM PST US
Subject: Pietenpol-List: Re: Ragwing Ultra-Piet
From: "cdlwingnut" <lee_chad@hotmail.com>


The fuselage is varnished and it is officially sitting on its landing gear. 

As far as why the little piet and not a full piet I answered that a while back
but mainly because i found a supply of 3/4" thick douglas fir and had an engine
already for it.


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=495238#495238


Attachments: 

http://forums.matronics.com//files/20200311_141238_resized_161.jpg
http://forums.matronics.com//files/20200311_141248_resized_939.jpg


________________________________  Message 2  _____________________________________


Time: 04:00:30 PM PST US
From: Glen Schweizer <glenschweizer@yahoo.com>
Subject: Re: Pietenpol-List: Re: Ragwing Ultra-Piet


Why are you trying to justify your decision?  The best reason ever is cuz thats
what I want to build. That was my first build. My main reason was quite similar
to yours plus back then, Roger Mann had a mod available for folding wings without
having to disconnect control cables. Only the cross over cable was unhooked(quick
disconnect) if I remember right. Quite a bit of airplane for a Nevada(20#heavy)
ultra lite 

> On Mar 11, 2020, at 3:31 PM, cdlwingnut <lee_chad@hotmail.com> wrote:
> 
> 
> The fuselage is varnished and it is officially sitting on its landing gear. 
> 
> As far as why the little piet and not a full piet I answered that a while back
but mainly because i found a supply of 3/4" thick douglas fir and had an engine
already for it.
> 
> 
> 
> 
> Read this topic online here:
> 
> http://forums.matronics.com/viewtopic.php?p=495238#495238
> 
> 
> 
> 
> Attachments: 
> 
> http://forums.matronics.com//files/20200311_141238_resized_161.jpg
> http://forums.matronics.com//files/20200311_141248_resized_939.jpg
> 
> 
> 
> 
> 
> 


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               pietenpol-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Pietenpol-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/pietenpol-list
Browse Digests                   http://www.matronics.com/digest/pietenpol-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.