----------------------------------------------------------
                           Pietenpol-List Digest Archive
                                      ---
                     Total Messages Posted Fri 04/24/20: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 09:38 AM - Re: Upper Brace Wire Fitting  (PoconoJohn2)
     2. 01:12 PM - Re: !/4" bolt in 5/8" wood?  (Clif Dawson)
     3. 01:18 PM - Re: !/4" bolt in 5/8" wood?  (PoconoJohn2)
 
 
 
________________________________  Message 1  _____________________________________


Time: 09:38:54 AM PST US
Subject: Pietenpol-List: Re: Upper Brace Wire Fitting
From: "PoconoJohn2" <redroof@protonmail.com>


Thank you gentlemen. Right now, my plan is to leave the spruce strip in position
per plans and raise the fitting above it (so 1.5" above plans position). The
hinge works out OK above all that keeping with the plans position.

I added a photo to show what is going on. Ignore the beam on top. The pencil is
between two lines. The lines represent the spruce strip. The pencil points at
the plans fitting location. You can see the 1/8" ply for the fitting. To the
left of that, you can see the hole for the eye bolt hinge and it's on the plans
location.

John C


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=496010#496010


Attachments: 

http://forums.matronics.com//files/piethinge2_646.jpg


________________________________  Message 2  _____________________________________


Time: 01:12:10 PM PST US
From: "Clif Dawson" <cdawson5854@shaw.ca>
Subject: Re: Pietenpol-List: !/4" bolt in 5/8" wood?


1/4" is 4/16. 5/8 is 10/16. The diff is 6/16 or 3/16 on either side of the 
bolt.

The photo didn't come through.

Clif
>
> If I'm reading the GN1 plan right (I'm applying this to my Pietenpol), I'm 
> supposed to put a 1/4" bolt into a beam which is mostly 5/8" wide (going 
> first through the 1" wide edge), so 1/16" margin on either side. Then, 
> once the nut is on, I'll have about 1/16" left (7/8" wood + 1/16" washer) 
> and I'm not sure if I'll get the minimum one full thread sticking out.
>
> If this is correct, should I reinforce the beam with 1/8" ply where the 
> bolt is only 1/16" away (on top and bottom surface in this photo)?
>
> John C


________________________________  Message 3  _____________________________________


Time: 01:18:59 PM PST US
Subject: Pietenpol-List: Re: !/4" bolt in 5/8" wood?
From: "PoconoJohn2" <redroof@protonmail.com>


Thank you. I saw my mistake right after I posted and deleted the post.


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=496024#496024


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               pietenpol-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Pietenpol-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/pietenpol-list
Browse Digests                   http://www.matronics.com/digest/pietenpol-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.