---------------------------------------------------------- Pulsar-List Digest Archive --- Total Messages Posted Tue 08/30/11: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:28 PM - Dynon Autopilot installation (Alex Kozloff) 2. 05:37 PM - Rick Thomasson's exhaust system maintenance (John Schussler) 3. 06:01 PM - Re: Dynon Autopilot installation (rockford67) ________________________________ Message 1 _____________________________________ Time: 04:28:27 PM PST US Subject: Pulsar-List: Dynon Autopilot installation From: "Alex Kozloff" Hey Gang: Has anyone installed a Dynon autopilot in their craft? If so, did you use the SV32 servos with the standard arm and the Generic Servo mounting kit? Did you go to the extra expense of adding the AP74 interface and wiring harness? Want to have this unit installed for the September Pulsar gathering in Lawrence, KS Anxious in Santa Paula, -- Alex Kozloff P.O. Box 866 Santa Paula, CA 93061 (949) 400-6364 Cell (805) 525-1415 Office _!_ O-O-(_)-O-O ________________________________ Message 2 _____________________________________ Time: 05:37:42 PM PST US From: "John Schussler" Subject: Pulsar-List: Rick Thomasson's exhaust system maintenance I am doing some deferred maintenace on my Pulsar after 500 flying hours in 11years. All the rubber replacement parts list. Any advice on that work? I pulled the exhaust to repair them while plane is down. Some general rust where Jet Hot coating flaked off and where new thicker tabs were welded on years ago. Two pinholes near welds are repaired with Cargo ThermoSteel, holding for now but will eventually come loose. I'd like to have muffler bead blasted, pinholes repaired and repainted. There are no cracks, just holes. What do you recommend? Weld over pinholes? Reweld joints and try to keep same alignment? What has been learned from field experience with this exhaust system? I don't follow the listvery well so may have missed new info during the past 6 years. I sent Rick an email asking for a update on his exhausting experience, but that addressed bounced. Rick- you out there? Probably in Lawrence... What has worked best to seal the exhaust joints- fiber/vermiculite strips from McMaster-Carr? I used stainless tape last time, held OK. Should I paint them with high temp alum finish or send them to Jet Hot to replace the original coating? Should I buy new mufflers? the pipes are all fine. John Schussler Pulsar XP ________________________________ Message 3 _____________________________________ Time: 06:01:22 PM PST US Subject: Pulsar-List: Re: Dynon Autopilot installation From: "rockford67" Hey Alex, I plan on the same installation and I haven't figured out which one yet either. Are you planning on altitude hold as well? Are you retrofitting a Dynon by any chance? I've got my eye on the Skyview. I look forward to seeing how you make out. Regards, Chris Read this topic online here: http://forums.matronics.com/viewtopic.php?p=351056#351056 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message pulsar-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Pulsar-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/pulsar-list Browse Digests http://www.matronics.com/digest/pulsar-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.