----------------------------------------------------------
                           Pulsar-List Digest Archive
                                      ---
                     Total Messages Posted Thu 09/12/13: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 07:50 AM - Re: Still looking for used/new right side window Pulsar XP  (helikhat@peak.org)
     2. 12:15 PM - Re: Re: Still looking for used/new right side window Pulsar XP  (Brian Anderson)
     3. 06:35 PM - Re: Re: Still looking for used/new right side window Pulsar XP  (Keith Palmer)
 
 
 
________________________________  Message 1  _____________________________________


Time: 07:50:34 AM PST US
From: helikhat@peak.org
Subject: Pulsar-List: Re: Still looking for used/new right side window Pulsar XP



________________________________  Message 2  _____________________________________


Time: 12:15:24 PM PST US
Subject: Re: Pulsar-List: Re: Still looking for used/new right side window Pulsar
XP
From: Brian Anderson <briana@xtra.co.nz>


Why not make one. It's not hard to take a mould. Create a female mould in fibreglass.
Form a piece of acrylic in the oven by letting it drape into the mould
Trim and fit. Voila !

Brian


On 13/09/2013, at 2:56 AM, Helikhat@peak.org wrote:

> 
> 
> 
> 
> 
> 


________________________________  Message 3  _____________________________________


Time: 06:35:19 PM PST US
From: "Keith Palmer" <kdpalmer@mweb.co.za>
Subject: Re: Pulsar-List: Re: Still looking for used/new right side window Pulsar
XP


I used polycarbinate which is flexible, all you need to do is trim and fit - 
No Problem.

K'd


----- Original Message ----- 
From: "Brian Anderson" <briana@xtra.co.nz>
Sent: Thursday, September 12, 2013 9:12 PM
Subject: Re: Pulsar-List: Re: Still looking for used/new right side window 
Pulsar XP


>
> Why not make one. It's not hard to take a mould. Create a female mould in 
> fibreglass. Form a piece of acrylic in the oven by letting it drape into 
> the mould Trim and fit. Voila !
>
> Brian
>
>
> On 13/09/2013, at 2:56 AM, Helikhat@peak.org wrote:
>
>>
>>
>>
>>
>>
>>
>
>
> 


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               pulsar-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Pulsar-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/pulsar-list
Browse Digests                   http://www.matronics.com/digest/pulsar-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.