---------------------------------------------------------- Pulsar-List Digest Archive --- Total Messages Posted Sat 08/08/20: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:05 AM - Re: Check Nut Size for Pulsar I (Sonja Englert) 2. 04:54 PM - Re: Check Nut Size for Pulsar I (mike mccann) ________________________________ Message 1 _____________________________________ Time: 07:05:24 AM PST US From: Sonja Englert Subject: Re: Pulsar-List: Check Nut Size for Pulsar I Typically jam nuts on rod ends are 1/4-28 threads (bolt diameter 1/4"). I am sure there are no size AN6 rod ends on a Pulsar. Sonja On Fri, Aug 7, 2020 at 2:44 PM Yellowhammer wrote: > > Greetings, > > I was wondering if anyone had the proper size for the check nuts that go > on the Rod End Bearings on the control linkages for the Pulsar I. > > Mine were missing when I acquired my kit. > > They seem to be the same size that would fit on an AN-6 bolt. > > I cannot figure out how to order the correct size. All I have seen on Air > Craft Spruce is for An-3 size. > > If I am looking up the nuts incorrectly please point me in the right > direction. > > I cannot close out my wings until I have the four that are required for > each wing's control linkages. > > Thanks in advance for the information as it is greatly appreciated. > > Yellowhammer > > -------- > J.M. Oyler "Clyde" > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=497567#497567 > > ________________________________ Message 2 _____________________________________ Time: 04:54:14 PM PST US From: mike mccann Subject: Re: Pulsar-List: Check Nut Size for Pulsar I I can confirm when I get to the hanger as my Pulsar 1 manuals are there, but I'm quite sure Sonja is correct. Mike McCann Pulsar 1-582 On Sat, Aug 8, 2020 at 7:06 AM Sonja Englert wrote: > Typically jam nuts on rod ends are 1/4-28 threads (bolt diameter 1/4"). I > am sure there are no size AN6 rod ends on a Pulsar. > > Sonja > > On Fri, Aug 7, 2020 at 2:44 PM Yellowhammer wrote: > >> >> Greetings, >> >> I was wondering if anyone had the proper size for the check nuts that go >> on the Rod End Bearings on the control linkages for the Pulsar I. >> >> Mine were missing when I acquired my kit. >> >> They seem to be the same size that would fit on an AN-6 bolt. >> >> I cannot figure out how to order the correct size. All I have seen on Air >> Craft Spruce is for An-3 size. >> >> If I am looking up the nuts incorrectly please point me in the right >> direction. >> >> I cannot close out my wings until I have the four that are required for >> each wing's control linkages. >> >> Thanks in advance for the information as it is greatly appreciated. >> >> Yellowhammer >> >> -------- >> J.M. Oyler "Clyde" >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=497567#497567 >> >> >> >> >> >> >> ========== >> ar-List" rel="noreferrer" target="_blank"> >> http://www.matronics.com/Navigator?Pulsar-List >> ========== >> FORUMS - >> eferrer" target="_blank">http://forums.matronics.com >> ========== >> WIKI - >> errer" target="_blank">http://wiki.matronics.com >> ========== >> b Site - >> -Matt Dralle, List Admin. >> rel="noreferrer" target="_blank">http://www.matronics.com/contribution >> ========== >> >> >> >> ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message pulsar-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Pulsar-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/pulsar-list Browse Digests http://www.matronics.com/digest/pulsar-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.