Today's Message Index:
----------------------
1. 10:09 AM - Re: Airfilter problem (Smoky Ray)
2. 12:25 PM - Re: Airfilter problem (Smoky Ray)
3. 02:13 PM - Re: Airfilter problem (Jim Stone)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Airfilter problem |
Do my best sir...
Smokey
--- On Tue, 10/7/08, Jim Stone <jrstone@insightbb.com> wrote:
From: Jim Stone <jrstone@insightbb.com>
Subject: Re: Rocket-List: Airfilter problem
#yiv1338319602 DIV {
MARGIN:0px;}
Smokey,
If you happen to have that K&N model number,
you might save me from ordering the wrong one.
Thanks,
Jim
HR2
----- Original Message -----
From:
Smoky
Ray
To: rocket-list@matronics.com
Sent: Monday, October 06, 2008 7:42
PM
Subject: Re: Rocket-List: Airfilter
problem
Jim,
-
- I'm using a K&N cone filter on my Harmon intake w/bypass, 3.5
inch top. Works great with my Skytech starter and clears the cowl with 2"
to
spare. Suprisingly, K&N had compettive prices...
-
Smokey
HR2
-----
Original Message ----
From: Jim Stone <jrstone@insightbb.com>
Sent:
Monday, October 6, 2008 6:42:56 PM
Subject: Re: Rocket-List: Airfilter
problem
Hey Tom,
Been doing some research on filters.- Your
part number was close but I came up with RB-0910 which is 5 inches high,
and
an RB-0900 which is 4 inches in height.- Do you think the 4 inch high o
ne
would work better, i.e., less contact with cowl and starter?
I also found some cone shapes which are about 5
inches high but have 3 1/2 inch diameter top, perhaps that would work, wh
at do
you think?
I wish my cowl was off so I could take some
measurements.- I just put it back on Sunday after the annual
inspection.
Jim Stone
Louisville KY
----- Original Message -----
From: Tom
Martin
To: rocket-list@matronics.com
Sent: Thursday, October 02, 2008 10:53
AM
Subject: RE: Rocket-List: Airfilter
problem
Jim
-----------
I had a similar set up on my second Harmon. -I used a conical K&N
filter that had a bit of an offset in the attach flange. -Part # RB
091.-- It did touch the starter and I put a big gob of RTV at the
point of contact. -It also tended to touch the cowling but never seem
ed
to cause and damage. -I do not see any reason why you could not squee
ze
a bit to get more clearance.- It is a nice simple
system.
-
Tom
Martin
-
From:
owner-rocket-list-server@matronics.com
[mailto:owner-rocket-list-server@matronics.com] On Behalf Of Jim Stone
Sent: October 2, 2008 10:39
AM
rocket-list@matronics.com
Subject: Rocket-List: Airfilter
problem
-
HR guys,
As per John Harmon's
recommendation, I have been using a UNI filter UP-6300 ast motorcycle
filter.- Not only do I not like the looks of the thing but it lays on
the inside of the cowl and has to deform a bit to do that, it also is
wearing where the cuff slides over the Y-valve.- I am using John's
intake Y valve and the angle of the filter side may not be quite
right.- Has anyone had this problem and or have a solution?-
Perhaps going to a K&N filter will do it, any model numbers would help
my search for a solution.
Thanks,
Jim
Stone - - -Checked by AVG.
Checked by AVG.
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/Navigator?Rocket-List"'>http://www.matr
onics.com/Navigator?Rocket-List
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://forums.matronics.com"'>http://forums.matronics.com
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/contribution"'>http://www.matronics.com
/contribution
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
=0A=0A=0A
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Airfilter problem |
Jim,
- I am 99% sure this is the one. I will pull my cowling and confirm it ne
xt week, hope it helps.
Smokey
HR2
http://www.knfilters.com/search/product.aspx?Prod=RF-1039
--- On Tue, 10/7/08, Smoky Ray <smokyray@rocketmail.com> wrote:
From: Smoky Ray <smokyray@rocketmail.com>
Subject: Re: Rocket-List: Airfilter problem
Do my best sir...
Smokey
--- On Tue, 10/7/08, Jim Stone <jrstone@insightbb.com> wrote:
From: Jim Stone <jrstone@insightbb.com>
Subject: Re: Rocket-List: Airfilter problem
#yiv68663337 #yiv1338319602 DIV {
MARGIN:0px;}
Smokey,
If you happen to have that K&N model number,
you might save me from ordering the wrong one.
Thanks,
Jim
HR2
----- Original Message -----
From:
Smoky
Ray
To: rocket-list@matronics.com
Sent: Monday, October 06, 2008 7:42
PM
Subject: Re: Rocket-List: Airfilter
problem
Jim,
-
- I'm using a K&N cone filter on my Harmon intake w/bypass, 3.5
inch top. Works great with my Skytech starter and clears the cowl with 2"
to
spare. Suprisingly, K&N had compettive prices...
-
Smokey
HR2
-----
Original Message ----
From: Jim Stone <jrstone@insightbb.com>
Sent:
Monday, October 6, 2008 6:42:56 PM
Subject: Re: Rocket-List: Airfilter
problem
Hey Tom,
Been doing some research on filters.- Your
part number was close but I came up with RB-0910 which is 5 inches high,
and
an RB-0900 which is 4 inches in height.- Do you think the 4 inch high o
ne
would work better, i.e., less contact with cowl and starter?
I also found some cone shapes which are about 5
inches high but have 3 1/2 inch diameter top, perhaps that would work, wh
at do
you think?
I wish my cowl was off so I could take some
measurements.- I just put it back on Sunday after the annual
inspection.
Jim Stone
Louisville KY
----- Original Message -----
From: Tom
Martin
To: rocket-list@matronics.com
Sent: Thursday, October 02, 2008 10:53
AM
Subject: RE: Rocket-List: Airfilter
problem
Jim
-----------
I had a similar set up on my second Harmon. -I used a conical K&N
filter that had a bit of an offset in the attach flange. -Part # RB
091.-- It did touch the starter and I put a big gob of RTV at the
point of contact. -It also tended to touch the cowling but never seem
ed
to cause and damage. -I do not see any reason why you could not squee
ze
a bit to get more clearance.- It is a nice simple
system.
-
Tom
Martin
-
From:
owner-rocket-list-server@matronics.com
[mailto:owner-rocket-list-server@matronics.com] On Behalf Of Jim Stone
Sent: October 2, 2008 10:39
AM
rocket-list@matronics.com
Subject: Rocket-List: Airfilter
problem
-
HR guys,
As per John Harmon's
recommendation, I have been using a UNI filter UP-6300 ast motorcycle
filter.- Not only do I not like the looks of the thing but it lays on
the inside of the cowl and has to deform a bit to do that, it also is
wearing where the cuff slides over the Y-valve.- I am using John's
intake Y valve and the angle of the filter side may not be quite
right.- Has anyone had this problem and or have a solution?-
Perhaps going to a K&N filter will do it, any model numbers would help
my search for a solution.
Thanks,
Jim
Stone - - -Checked by AVG.
Checked by AVG.
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/Navigator?Rocket-List"'>http://www.matr
onics.com/Navigator?Rocket-List
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://forums.matronics.com"'>http://forums.matronics.com
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/contribution"'>http://www.matronics.com
/contribution
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
=0A=0A=0A
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Airfilter problem |
Thanks Smokey,
Please don't pull that cowl for me. I await your confirmation. BTW,
send me a pic of yours so I can put a name to a Rocket.
Jim Stone
PS Attached is a pic of my ride
----- Original Message -----
From: Smoky Ray
To: rocket-list@matronics.com
Sent: Tuesday, October 07, 2008 3:25 PM
Subject: Re: Rocket-List: Airfilter problem
Jim,
I am 99% sure this is the one. I will pull my cowling and
confirm it next week, hope it helps.
Smokey
HR2
http://www.knfilters.com/search/product.aspx?Prod=RF-1039
--- On Tue, 10/7/08, Smoky Ray <smokyray@rocketmail.com> wrote:
From: Smoky Ray <smokyray@rocketmail.com>
Subject: Re: Rocket-List: Airfilter problem
To: rocket-list@matronics.com
Date: Tuesday, October 7, 2008, 5:09 PM
Do my best sir...
Smokey
--- On Tue, 10/7/08, Jim Stone <jrstone@insightbb.com>
wrote:
From: Jim Stone <jrstone@insightbb.com>
Subject: Re: Rocket-List: Airfilter problem
To: rocket-list@matronics.com
Date: Tuesday, October 7, 2008, 1:12 AM
Smokey,
If you happen to have that K&N model number, you might
save me from ordering the wrong one.
Thanks,
Jim
HR2
----- Original Message -----
From: Smoky Ray
To: rocket-list@matronics.com
Sent: Monday, October 06, 2008 7:42 PM
Subject: Re: Rocket-List: Airfilter problem
Jim,
I'm using a K&N cone filter on my Harmon intake
w/bypass, 3.5 inch top. Works great with my Skytech starter and clears
the cowl with 2" to spare. Suprisingly, K&N had compettive prices...
Smokey
HR2
----- Original Message ----
From: Jim Stone <jrstone@insightbb.com>
To: rocket-list@matronics.com
Sent: Monday, October 6, 2008 6:42:56 PM
Subject: Re: Rocket-List: Airfilter problem
Hey Tom,
Been doing some research on filters. Your part
number was close but I came up with RB-0910 which is 5 inches high, and
an RB-0900 which is 4 inches in height. Do you think the 4 inch high
one would work better, i.e., less contact with cowl and starter?
I also found some cone shapes which are about 5
inches high but have 3 1/2 inch diameter top, perhaps that would work,
what do you think?
I wish my cowl was off so I could take some
measurements. I just put it back on Sunday after the annual inspection.
Jim Stone
Louisville KY
----- Original Message -----
From: Tom Martin
To: rocket-list@matronics.com
Sent: Thursday, October 02, 2008 10:53 AM
Subject: RE: Rocket-List: Airfilter problem
Jim
I had a similar set up on my second
Harmon. I used a conical K&N filter that had a bit of an offset in the
attach flange. Part # RB 091. It did touch the starter and I put a
big gob of RTV at the point of contact. It also tended to touch the
cowling but never seemed to cause and damage. I do not see any reason
why you could not squeeze a bit to get more clearance. It is a nice
simple system.
Tom Martin
----------------------------------------------------------
From: owner-rocket-list-server@matronics.com
[mailto:owner-rocket-list-server@matronics.com] On Behalf Of Jim Stone
Sent: October 2, 2008 10:39 AM
To: rocket-list@matronics.com
Subject: Rocket-List: Airfilter problem
HR guys,
As per John Harmon's recommendation, I have been
using a UNI filter UP-6300 ast motorcycle filter. Not only do I not
like the looks of the thing but it lays on the inside of the cowl and
has to deform a bit to do that, it also is wearing where the cuff slides
over the Y-valve. I am using John's intake Y valve and the angle of the
filter side may not be quite right. Has anyone had this problem and or
have a solution? Perhaps going to a K&N filter will do it, any model
numbers would help my search for a solution.
Thanks,
Jim Stone
Checked by AVG.
Checked by AVG.
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3Dhref='3D"http://www.matronics.com/Navigator?Rocket-List"'>http://www.
matronics.com/Navigator?Rocket-List3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3Dhref='3D"http://forums.matronics.c
om"'>http://forums.matronics.com3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3Dhref='3D"http://www.matronics.com/
contribution"'>http://www.matronics.com/contribution3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|