Today's Message Index:
----------------------
1. 08:07 AM - Re: RotaxEngines-List Digest: 2 Msgs - 10/14/06 (Tew, Stan)
2. 08:41 AM - Kitfox Numbers (Guy Buchanan)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | RE: RotaxEngines-List Digest: 2 Msgs - 10/14/06 |
--> RotaxEngines-List message posted by: "Tew, Stan" <Stan.Tew@revenue.alabama.gov>
I have been running a 69" with 3 standard shaped blades on my 582 in
Kitfox for several years. In fact, this is the 2nd engine the prop has
been mounted on. I find it works great except that the mass moment
forces a high idle speed to reduce vibration.
-----Original Message-----
From: owner-rotaxengines-list-server@matronics.com
[mailto:owner-rotaxengines-list-server@matronics.com] On Behalf Of
RotaxEngines-List Digest Server
Sent: Sunday, October 15, 2006 1:57 AM
Subject: RotaxEngines-List Digest: 2 Msgs - 10/14/06
*
=================================================
Online Versions of Today's List Digest Archive
=================================================
Today's complete RotaxEngines-List Digest can also be found in either of
the
two Web Links listed below. The .html file includes the Digest
formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the RotaxEngines-List Digest and can be viewed with a generic text
editor
such as Notepad or with a web browser.
HTML Version:
http://www.matronics.com/digest/rotaxengines-list/Digest.RotaxEngines-Li
st.2006-10-14.html
Text Version:
http://www.matronics.com/digest/rotaxengines-list/Digest.RotaxEngines-Li
st.2006-10-14.txt
===============================================
EMail Version of Today's List Digest Archive
===============================================
----------------------------------------------------------
RotaxEngines-List Digest Archive
---
Total Messages Posted Sat 10/14/06: 2
----------------------------------------------------------
Today's Message Index:
----------------------
1. 09:54 AM - Warp Drive Hub (Guy Buchanan)
2. 10:47 AM - Re: Warp Drive Hub (Duncan & Ami McFadyean)
________________________________ Message 1
_____________________________________
Time: 09:54:10 AM PST US
From: Guy Buchanan <bnn@nethere.com>
Subject: RotaxEngines-List: Warp Drive Hub
--> RotaxEngines-List message posted by: Guy Buchanan <bnn@nethere.com>
All,
Donny, one of the locals, suggested that I was over-propped and
that was why my performance was off. (I'm running a 70" Warp 3-blade on
my
Rotax 582 with a 3:1 "C" box.) He suggested I go to two blades, or
change
the ratio to 3.47:1. Toward that end, I'm looking to see if anyone has a
Warp two blade hub or some 3.47:1 "C" box gears that I might
beg/borrow/buy.
Thanks,
Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.
________________________________ Message 2
_____________________________________
Time: 10:47:59 AM PST US
From: "Duncan & Ami McFadyean" <ami@MCFADYEAN.FREESERVE.CO.UK>
Subject: Re: RotaxEngines-List: Warp Drive Hub
--> RotaxEngines-List message posted by: "Duncan & Ami McFadyean"
<ami@mcfadyean.freeserve.co.uk>
Not sure what aircraft you're using this on, but by way of comparison I
have
seen a 72" 3-blade Warp Drive used with 582 and C-box (3:1) on an Avid
Speedwind. It worked well.
The difference may have been in the backtaper on hte blades, which was
fairly extreme such that the chord length at hte tip was only about 1".
However, Warp Drive themselves set this up. So it might be worthwhile
asking
them.
Duncan McF.
----- Original Message -----
From: "Guy Buchanan" <bnn@nethere.com>
Sent: Saturday, October 14, 2006 5:53 PM
Subject: RotaxEngines-List: Warp Drive Hub
> --> RotaxEngines-List message posted by: Guy Buchanan
<bnn@nethere.com>
>
> All,
> Donny, one of the locals, suggested that I was over-propped
and
> that was why my performance was off. (I'm running a 70" Warp 3-blade
on my
> Rotax 582 with a 3:1 "C" box.) He suggested I go to two blades, or
change
> the ratio to 3.47:1. Toward that end, I'm looking to see if anyone has
a
> Warp two blade hub or some 3.47:1 "C" box gears that I might
> beg/borrow/buy.
>
> Thanks,
>
>
> Guy Buchanan
> K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> RotaxEngines-List message posted by: Guy Buchanan <bnn@nethere.com>
At 08:06 AM 10/16/2006, you wrote:
>I have been running a 69" with 3 standard shaped blades on my 582 in
>Kitfox for several years.
Stan. What tip angle are you using? What are your wide-open and cruise
speeds? What is your climb rate? What model Kitfox is it?
Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|