Today's Message Index:
----------------------
1. 05:34 AM - Re: Firesleeve Ends (h&jeuropa)
2. 10:17 AM - 503 Hard start (Scott Mac.)
3. 11:46 AM - Re: 503 Hard start (Dave G.)
4. 12:01 PM - Re: 503 Hard start (ElleryWeld@aol.com)
5. 08:27 PM - Re: 503 Hard start (NYTerminat@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Firesleeve Ends |
Hugh,
At the PAMA seminar they specificially mentioned Toluene. We'd guess other agressive
solvents would be OK but don't know for sure. We don't think mineral spirits
would work.
Jim and Heather
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=105612#105612
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I'm new to Ultralights and Rotax motors and I just purchased a '91 Kolb Mk II with
a 503 DDIC. The engine is equipped with a pull start. and the only time
I'm successful starting this motor is if I use starting fluid. Any suggestions
as to what adjustments is necessary?
--------
Scott Mac.
MK II
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=105691#105691
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 503 Hard start |
Sounds like it's past due for new seals.
Do not archive
----- Original Message -----
From: "Scott Mac." <sdmacp@yahoo.com>
Sent: Sunday, April 08, 2007 2:16 PM
Subject: RotaxEngines-List: 503 Hard start
>
> I'm new to Ultralights and Rotax motors and I just purchased a '91 Kolb Mk
> II with a 503 DDIC. The engine is equipped with a pull start. and the
> only time I'm successful starting this motor is if I use starting fluid.
> Any suggestions as to what adjustments is necessary?
>
> --------
> Scott Mac.
> MK II
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=105691#105691
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 503 Hard start |
First of all DO NOT use starting fluid especially on a two stroke that gets
it lube throught the fuel, install a primer pump to squirt gas in the intake
manifold and you shouldnt have any problems starting but if you already have
tyhat system and use it then you have other problems what type of ignition
systerm and Dual or single might need more info to really help you
Ellery
Do Not Archive
**************************************
See what's free at
http://www.aol.com.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 503 Hard start |
Scott,
Not sure if the Bing carb is like a Rotax 912 but with the 912 the throttle
must be closed to start the engine. If you open the throttle it will not
start. If that is not the case then a primer will do the trick.
In a message dated 4/8/2007 2:47:26 P.M. Eastern Daylight Time,
occom@ns.sympatico.ca writes:
--> RotaxEngines-List message posted by: "Scott Mac." <sdmacp@yahoo.com>
>
> I'm new to Ultralights and Rotax motors and I just purchased a '91 Kolb Mk
> II with a 503 DDIC. The engine is equipped with a pull start. and the
> only time I'm successful starting this motor is if I use starting fluid.
> Any suggestions as to what adjustments is necessary?
>
> --------
> Scott Mac.
> MK II
************************************** See what's free at http://www.aol.com.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|