Today's Message Index:
----------------------
 
     1. 02:48 PM - Bing 54 (rayw)
     2. 02:57 PM - Re: Bing 54 (Bob Comperini)
     3. 08:21 PM - Rotax 912 Warning lights (marcflyer)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
02:48:15 PM PST US
Subject: 
Bing 54
From: 
"rayw" <rmwis@charter.net>
      
      
      Hi all,
      
      I have a 503 DCSI with Bing 54 carbs. Are the jet needles, now, supposed to be
      held in place with o rings, clips or both? 
      
      Just a side note. I found one needle bent (with an o ring) and the needle in the
      other carb was ok (with a rusty clip).
      
      I Just bought this Kolb and I am finding all kinds of surprises.
      
      Thanks,
      
      Ray W.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=259021#259021
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
02:57:18 PM PST US
From: 
Bob Comperini <bob@fly-ul.com>
Subject: 
Re: Bing 54
      
      
      
      On 02:47 PM 8/21/2009, rayw wrote:
      >
      >I have a 503 DCSI with Bing 54 carbs. Are the jet needles, now, supposed to be
      held in place with o rings, clips or both? 
      
      Basically "both". Obviously, the needle is held in place with the circlip. Several
      years ago, they added the "O-ring" thing, to prevent the needle from wearing
      out. Note: This also included a new design white plastic "cup" (I forget what
      its called), that has a little recess in it to accept the O-Ring.
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
08:21:40 PM PST US
Subject: 
Rotax 912 Warning lights
From: 
"marcflyer" <marcelgina2@hotmail.com>
      
      
      Has any one tried to install Oil Press and Water Temp warning lights, if so where
      does one get the dual sending units in metric. I use VDO guages
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=259052#259052
      
      








Other Matronics Email List Services




Post A New Message
  
rotaxengines-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RotaxEngines-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/rotaxengines-list
Browse RotaxEngines-List Digests
  
http://www.matronics.com/digest/rotaxengines-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --