Today's Message Index:
----------------------
1. 03:52 AM - Re: Re: Bing 54 flooding only 1 cylinder - where is the dirt lodged? (Robert C Harrison)
2. 04:53 AM - Re: Re: Bing 54 flooding only 1 cylinder - where is the dirt lodged? (Richard Girard)
3. 07:58 AM - Re: Bing 54 flooding only 1 cylinder - where is the dirt lodged? (Tom Jones)
4. 08:56 AM - Re: Bing 54 flooding only 1 cylinder - where is the dirt lodged? (wildirishtime)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bing 54 flooding only 1 cylinder - where is |
the dirt lodged?
Yes. And verify the spark.
Regards
Bob.
-----Original Message-----
From: owner-rotaxengines-list-server@matronics.com
[mailto:owner-rotaxengines-list-server@matronics.com] On Behalf Of
wildirishtime
Sent: 26 February 2010 07:52
Subject: RotaxEngines-List: Re: Bing 54 flooding only 1 cylinder - where is
the dirt lodged?
<brendan@structuredinc.com>
Well do you mean 'float valve'? Remember, the engine was running perfect
just the day prior to my swapping out the rubber hoses - it's about 99% sure
and obstruction in my book.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288265#288265
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bing 54 flooding only 1 cylinder - where is |
the dirt lodged?
Happened to me recently on a Bing 54. Crap on the needle valve. With the 64,
you might want to check that you got the tab on the diaphragm back in its
slot, too.
Rick Girard
On Fri, Feb 26, 2010 at 3:08 AM, Robert C Harrison
<ptag.dev@tiscali.co.uk>wrote:
> ptag.dev@tiscali.co.uk>
>
> Yes. And verify the spark.
> Regards
> Bob.
>
> -----Original Message-----
> From: owner-rotaxengines-list-server@matronics.com
> [mailto:owner-rotaxengines-list-server@matronics.com] On Behalf Of
> wildirishtime
> Sent: 26 February 2010 07:52
> To: rotaxengines-list@matronics.com
> Subject: RotaxEngines-List: Re: Bing 54 flooding only 1 cylinder - where is
> the dirt lodged?
>
> <brendan@structuredinc.com>
>
> Well do you mean 'float valve'? Remember, the engine was running perfect
> just the day prior to my swapping out the rubber hoses - it's about 99%
> sure
> and obstruction in my book.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=288265#288265
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bing 54 flooding only 1 cylinder - where is the |
dirt lodged?
Wet plugs doesn't seem to fit with the problem being an obstruction in one of the
carb circuits. Check to be sure the enricher plunger (choke) is seating properly
on the wet cylinder's carb.
--------
Tom Jones
Classic IV
503 Rotax, 72 inch Two blade Warp
Ellensburg, WA
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288297#288297
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bing 54 flooding only 1 cylinder - where is the |
dirt lodged?
Tom Jones was correct - for some reason it was NOT dirt - I just
haven't utilized the choke enough to realize it was intermittently
hanging open. I apparently flipped it on to get her running after
all my fuel lines were replaced (empty) in hopes it would pull
the fuel in faster to my empty fuel system. The lever-style
choke handle isnt' returning. I'll reassemble my carb and verify
before I go chasing it. If anyone has seen these carb cables
hang up, please let me know how you suggest resolving it...
do I open and lubricate the cables, or is there a spring somewhere
inside the choke handle or ??
Thanks all!
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288313#288313
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|