Today's Message Index:
----------------------
1. 03:45 AM - Re:25 stainless cable ties for 5$ (ruruny@aol.com)
2. 05:58 AM - Re: 25 stainless cable ties for 5$ (Catz631@aol.com)
3. 10:10 AM - Tricks For Replacing Bottom Coolant Hose On 912? (Goodone)
4. 11:19 AM - Re: 25 stainless cable ties for 5$ (rparigoris)
5. 09:39 PM - Re: Tricks For Replacing Bottom Coolant Hose On 912? (Roger Lee)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re:25 stainless cable ties for 5$ |
Ron,
Thats funny you mentioned this, I had that same pack in my hands the other
day. Not doing any firesleeve right
now so I put them back. Store in Bayshore, right?
Brian
STOL 701 80hrs 912 80hp
http://www.zenith.aero/profile/BrianKUnruh
http://www.701builder.com
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 25 stainless cable ties for 5$ |
I have used the Harbor Freight SS ties for a few years now to attach my
exhaust wrap. They work great and have never failed.
Dick Maddux
912UL
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Tricks For Replacing Bottom Coolant Hose On 912? |
Any tricks or suggestions on how to remove and replace the 17mm coolant hose on
the bottom of a Rotax 912? By taking off the coolant flange attached to the
head on the top of the engine it has made the top job a bit easier. Any good methods
for the bottom hose replacement?
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=362487#362487
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 25 stainless cable ties for 5$ |
Hi Brian
(STOL 701 80hrs 912 80hp)
The new Harbor Freight I stopped by is located in Commack in the old Linens and
Things. It is on 454 just west of Sunken Meadow Parkway on the south side (just
East of Target).
In other words East of the 454 intersection with 25 in Commack.
It's closer to me and easier to get to than the Bayshore location.
Ron Parigoris
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=362495#362495
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Tricks For Replacing Bottom Coolant Hose On 912? |
I've done a lot of 5 year rubber hose replacements and you shouldn't have to remove
any coolant fittings. I can usually pull the hoses off and slide them back
on with either a constant compression clamp or a screw clamp. I don't usually
have to remove any fuel fittings. If you cause the coolant 90 degree fittings
on the top or the bottom of the engine to come loose (swivel back and forth)
then you will need to pull that fitting and unscrew it then re-apply some Loctite
648 and put the fitting back in place and let it sit overnight in the aligned
position that you will need.
--------
Roger Lee
Tucson, Az.
Light Sport Repairman - Maintenance Rated
Rotax Repair Center - Heavy Maint. Rated
Home 520-574-1080 TRY HOME FIRST
Cell 520-349-7056
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=362558#362558
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|