RotaxEngines-List Digest Archive

Tue 08/05/14


Total Messages Posted: 1



Today's Message Index:
----------------------
 
     1. 08:54 AM - Re: Low RPM on Takeoff??? (kerrimikehickman)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:54:49 AM PST US
    Subject: Re: Low RPM on Takeoff???
    From: kerrimikehickman <kerrimikehickman@aol.com>
    I had that exact problem w/912ULS...=0A=0A=0A-Findings: very small hairline crack/approx. 2mm long in very small indentation (or igin unknown) in top of one carb housing...=0A(discovered after sending carbs to LEAF for routine ultrasonic cleaning/rubber rep lacement).=0A=0A=0A--Result: replacement of carb top housing led t o normal engine operation at all power settings.=0ACheers=0AMike=0A =0A=0A-----Original Message-----=0AFrom: tmitton <tmitton99@gmail.com>=0AT o: rotaxengines-list <rotaxengines-list@matronics.com>=0ASent: Mon, Aug 4, 2014 6:12 pm=0ASubject: RotaxEngines-List: Low RPM on Takeoff ton99@gmail.com>=0A=0ARecently my 912ULS engine started only going to 5000rpm on takeoff with full =0Athrottle.=0A=0APreviously it always went directly to 5500rpm or so upon application of fu ll =0Apower. Now it only goes above 5000rpm once it has be en flying for a few minutes. =0AOnce flying it will still go to 5500+ even in a climb so it isn't like it is =0A just the climbing load on take off that is holding it back . =0A=0ANo changes have been made to the engine so I don't know what would cause the RPM =0Adrop. It is enough that takes offs now need 1000+ feet where as before 500-600ft =0A was enough. There is definitely a noticeable difference. =0A=0AI have checked the carburetor linkages - full throw to the stops there. Drained =0Athe gas in case it was old and rep laced it with fresh new gas - no change. Tried =0Ait with half a tank of 100LL to give it an octane boost - no c hange. Checked the =0Aspark plugs - still clean after only 2 5hrs of use. Nothing stuck on the rads. =0AOil topped up.=0A =0ASo - any idea as to what might cause the drop in rpm? =0A=0A=0A=0A=0ARead this topic online here:=0A=0Ahttp://forums.matronics =========================== =========================== =========================== = - MATRONICS WEB FORUMS - =========================== =========================== =========================== ===============0A=0A=0A=0A=0A =0A=0A




    Other Matronics Email List Services

  • Post A New Message
  •   rotaxengines-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/RotaxEngines-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/rotaxengines-list
  • Browse RotaxEngines-List Digests
  •   http://www.matronics.com/digest/rotaxengines-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --