Today's Message Index:
----------------------
1. 10:49 AM - 912 oil return line in silicon (JohnFrance)
2. 10:58 AM - Re: 912 oil return line in silicon (Robert Toth)
3. 11:01 AM - Re: 912 oil return line in silicon (Robert Toth)
4. 01:38 PM - Re: 912 oil return line in silicon (SPURPURA)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 912 oil return line in silicon |
Hello,
I am replacing the hoses on my 912 and I am thinking of using silicon hose for
the oil return line. This is probably the hose that is the most affected by heat
as just above the exhaust system. It works in a low over pressure environment
of around 0,35 bar yet I have never seen a silicon tube used on this line.
On the other hand the oil pump feed line (used in an under pressure environment)
is often made of silicon.
Is there a reason for not using a silicon return line as the rubber ones harden
due to heat?
Regards,
John
--------
Europa mono Nr 192
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=494929#494929
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 912 oil return line in silicon |
I think silIcone is good just watch your routing!
Sent from my iPhone
> On Feb 21, 2020, at 1:53 PM, JohnFrance <77alembert@gmail.com> wrote:
>
>
> Hello,
> I am replacing the hoses on my 912 and I am thinking of using silicon hose for
the oil return line. This is probably the hose that is the most affected by
heat as just above the exhaust system. It works in a low over pressure environment
of around 0,35 bar yet I have never seen a silicon tube used on this line.
On the other hand the oil pump feed line (used in an under pressure environment)
is often made of silicon.
> Is there a reason for not using a silicon return line as the rubber ones harden
due to heat?
> Regards,
> John
>
> --------
> Europa mono Nr 192
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=494929#494929
>
>
>
>
>
>
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 912 oil return line in silicon |
John I believe silicon is fine just watch the routing around the exhaust. I have
them on my 912
Sent from my iPhone
> On Feb 21, 2020, at 1:53 PM, JohnFrance <77alembert@gmail.com> wrote:
>
>
> Hello,
> I am replacing the hoses on my 912 and I am thinking of using silicon hose for
the oil return line. This is probably the hose that is the most affected by
heat as just above the exhaust system. It works in a low over pressure environment
of around 0,35 bar yet I have never seen a silicon tube used on this line.
On the other hand the oil pump feed line (used in an under pressure environment)
is often made of silicon.
> Is there a reason for not using a silicon return line as the rubber ones harden
due to heat?
> Regards,
> John
>
> --------
> Europa mono Nr 192
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=494929#494929
>
>
>
>
>
>
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 912 oil return line in silicon |
Silicone will work but Id still fire sleeve it.
--------
N951EU - Tri-gear & 912ULS, N77EU- Mono & 914
I'D RATHER HAVE A BOTTLE IN FRONT OF ME THAN A FRONTAL LABOTAMY.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=494934#494934
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|