---------------------------------------------------------- RV-List Digest Archive --- Total Messages Posted Sun 04/06/03: 10 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:51 AM - Re: No nylocks on anything subject to rotation (Jim Sears) 2. 08:01 AM - #22 size pin removal tool...S-Tec installation (Ralph E. Capen) 3. 08:31 AM - Re: R-904 Bottom Rib (Rudder) (Elsa & Henry) 4. 09:02 AM - Re: #22 size pin removal tool...S-Tec installation (RICKRV6@aol.com) 5. 09:12 AM - Re: #22 size pin removal tool...S-Tec installation (Elsa & Henry) 6. 02:05 PM - RV8 IO360-A1B (Gert) 7. 04:56 PM - Re: RV8 IO360-A1B (Vanremog@aol.com) 8. 06:59 PM - Wayne Handley Seminar (ACE) 9. 07:04 PM - Wayne Handley Seminar (ACE) 10. 09:10 PM - Re: Wayne Handley Seminar (aronsond) ________________________________ Message 1 _____________________________________ Time: 03:51:43 AM PST US From: "Jim Sears" Subject: Re: RV-List: No nylocks on anything subject to rotation --> RV-List message posted by: "Jim Sears" > Just because 500 people did it wrong doesn't make it right! > There are mixed feelings on this subject. I've discussed it often with my IA buddies who say it's OK to use them if done with care. I also had a Grumman-American Cheetah that had them firewall forward. I flew it for over 9.5 years and had no trouble with them. I used them in my RV's engine compartment and am not losing sleep over it. The main thing is to not use them near the exhaust system. We don't want the nylon friction device to be melted by the heat. To make sure all is well with them, just check the ones that concern you at oil changes, annuals, etc. The one on my RV's nose gear seems to be doing OK after three years and over 200 hours of operation. I'd almost be willing to bet that Van's Old Blue RV-6A has one of those nuts on the nose gear. Right, or wrong, it seems to work without failure. OK, to add fuel to the fire. Should we use nylon tie wraps firewall forward? I'm betting that any of you who've been around airplanes very much have seen a ton of them in front of the firewall, just as I have. :-) Jim Sears in KY RV-6A N198JS EAA Tech Counselor ________________________________ Message 2 _____________________________________ Time: 08:01:00 AM PST US From: "Ralph E. Capen" Subject: RV-List: #22 size pin removal tool...S-Tec installation --> RV-List message posted by: "Ralph E. Capen" Hey listers, Anyone out there have a #22 size pin removal/insertion tool? It would be smaller than the tool that you would use on your UPSAT gear (I have one of those). It is for the high density connectors (like S-Tec). If so, where did you get it? I've already tried mouser/digikey/altex...all they have is the bigger ones. I know that this is a fairly inexpensive tool...but when you don't have one it's worth a fortune...! I've already sent a zap to the connector manufacturer - but I thought I'd try you guy/gals too! Thanks for your assistance, Ralph Capen Wiring my 6A in Richardson, TX ________________________________ Message 3 _____________________________________ Time: 08:31:55 AM PST US From: "Elsa & Henry" Subject: Re: RV-List: R-904 Bottom Rib (Rudder) --> RV-List message posted by: "Elsa & Henry" Pursuant to Patrick Kelly's response to the subject, I used a piece of 2" X 2" X 1/8" thk. angle iron firmly clamped in a drill-press vice to hold it. I had cut the side that will do the bucking to 3/4" wide, (enough to enter the space between the rib flanges), and polished it on a belt sander. I countersunk a #40 hole to act as a female dimple-die.- Worked fine! Then it worked great to buck the rivets. I cut the length of the angle-iron to the width of the jaws of the drill-press vice to provide ample rigidity to absorb the riveting shock impulses. I found this "tool" useful in other tight spaces on tapered ends of control surfaces. As it turned out I ended cutting-off the rear tip of the rudder (where I first used it), to install a Whelen tail/strobe light combination there! Oh well-- Cheers!!------Henry Hore ________________________________ Message 4 _____________________________________ Time: 09:02:27 AM PST US From: RICKRV6@aol.com Subject: Re: RV-List: #22 size pin removal tool...S-Tec installation --> RV-List message posted by: RICKRV6@aol.com In a message dated 4/6/03 11:02:23 AM Eastern Daylight Time, recapen@earthlink.net writes: > Hey listers, > > Anyone out there have a #22 size pin removal/insertion tool? It would be > smaller than the tool that you would use on your UPSAT gear (I have one of > those). It is for the high density connectors (like S-Tec). > > If so, where did you get it? I've already tried mouser/digikey/altex...all > they have is the bigger ones. I know that this is a fairly inexpensive > tool...but when you don't have one it's worth a fortune...! > > I've already sent a zap to the connector manufacturer - but I thought I'd > try you guy/gals too! > > Thanks for your assistance, > Ralph Capen > Wiring my 6A in Richardson, TX Ralph, I needed the same tool to reverse the servo direction in my S-Tec 30 and to run the cable through numerous conduits. I called tech support and they sent me two different size tools, gratis. Rick McBride ________________________________ Message 5 _____________________________________ Time: 09:12:06 AM PST US From: "Elsa & Henry" Subject: Re: RV-List: #22 size pin removal tool...S-Tec installation --> RV-List message posted by: "Elsa & Henry" Check the Cannon catalog. We used theirs, at work years ago, and maybe you'll find what you need. Cheers!! Henry Hore ________________________________ Message 6 _____________________________________ Time: 02:05:14 PM PST US From: Gert rv-list Subject: RV-List: RV8 IO360-A1B --> RV-List message posted by: Gert Hi Can somebody please tell me the correct AN number for plugs to plug the holes in the cylinder headss where the injector nozzles currently are ?? it's a angle valve...IO360-A1B Thanks !! gert -- is subject to a download and archival fee in the amount of $500 ________________________________ Message 7 _____________________________________ Time: 04:56:22 PM PST US From: Vanremog@aol.com Subject: Re: RV-List: RV8 IO360-A1B --> RV-List message posted by: Vanremog@aol.com In a message dated 4/6/2003 2:06:18 PM Pacific Daylight Time, gert@execpc.com writes: > Can somebody please tell me the correct AN number for plugs to plug the > holes in the cylinder heads where the injector nozzles currently are ?? > AN932-2 (1/8"MNPT steel hex socket plug). I couldn't find the steel version in ACS or Wicks, but this is what you should use. The aluminum ones could cold weld themselves into the head after a time, so steel is better in this application. -GV (RV-6A N1GV 596hrs) ________________________________ Message 8 _____________________________________ Time: 06:59:56 PM PST US From: ACE Subject: RV-List: Wayne Handley Seminar --> RV-List message posted by: ACE I would like to let everyone know that April 26-27 EAA Chapter 90 in Oakdale Ca. (O27) is hosting a stall spin seminar. The seminar is presented by the inverted flat spin world record holder Wayne Handley. This event is open to the public. The price for the seminar is $30.00 which includes lunch. There are a few slots open for a flight with Wayne in his Extra 300L, anyone interested in attending or scheduling a flight can visit www.eaa90.org or contact Keith Braun at 209.605.4700 ________________________________ Message 9 _____________________________________ Time: 07:04:30 PM PST US From: ACE Subject: RV-List: Wayne Handley Seminar --> RV-List message posted by: ACE I would like to let everyone know that April 26-27 EAA Chapter 90 in Oakdale Ca. (O27) is hosting a stall spin seminar. The seminar is presented by the inverted flat spin world record holder Wayne Handley. This event is open to the public. The price for the seminar is $30.00 which includes lunch. There are a few slots open for a flight with Wayne in his Extra 300L, anyone interested in attending or scheduling a flight can visit www.eaa90.org or contact Keith Braun at 209.605.4700 Thanks Keith Braun N237RV RV7A Finish Kit ________________________________ Message 10 ____________________________________ Time: 09:10:29 PM PST US From: "aronsond" Subject: Re: RV-List: Wayne Handley Seminar --> RV-List message posted by: "aronsond" Hey Keith: We are having Wayne at the Nut Tree on April 12th. Same event. We arent going to sell 40 tickets......... How are your tickets selling? Would like to know just to see if Wayne is saturating the market. Dave Aronson Solano Pilots Association ----- Original Message ----- From: "ACE" Subject: RV-List: Wayne Handley Seminar > --> RV-List message posted by: ACE > > I would like to let everyone know that April 26-27 EAA Chapter 90 in Oakdale Ca. (O27) is hosting a stall spin seminar. The seminar is presented by the inverted flat spin world record holder Wayne Handley. This event is open to the public. The price for the seminar is $30.00 which includes lunch. There are a few slots open for a flight with Wayne in his Extra 300L, anyone interested in attending or scheduling a flight can visit www.eaa90.org or contact Keith Braun at 209.605.4700 > > Thanks > Keith Braun > N237RV RV7A Finish Kit > >