Today's Message Index:
----------------------
1. 06:05 AM - Re: Com/Nav Antenna Connectors (Wayne R. Couture)
2. 06:52 AM - Re: RV-7 Trim Access Plate (Emrath)
3. 07:21 AM - Re: Dimpling nutplates (Mark Phillips)
4. 08:12 AM - Re: Dimpling nutplates (Tim Lewis)
5. 01:28 PM - [ John Starn ] : New Email List Photo Share Available! (Email List Photo Shares)
6. 01:31 PM - [ John Starn ] : New Email List Photo Share Available! (Email List Photo Shares)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Com/Nav Antenna Connectors |
--> RV-List message posted by: "Wayne R. Couture" <commando@cox-internet.com>
IMHO, "Amphenol" makes the best RF connectors on the market. It does take
some expertise to put them on correctly but well worth the trouble.
Wayne
----- Original Message -----
From: "Roger Evenson" <revenson@comcast.net>
Subject: RV-List: Com/Nav Antenna Connectors
> --> RV-List message posted by: "Roger Evenson" <revenson@comcast.net>
>
> What kind of antenna cable connectors are used for Com and Nav radios? Is
there consistency among manufacturers?
> Roger, Tucson.
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-7 Trim Access Plate |
--> RV-List message posted by: "Emrath" <emrath@comcast.net>
Karie,
My RV-6 empennage came with some button head screws for this access
cover. I changed it to flush head after ordering new screws and dimpled
nut plates. K1100-6 I believe. Hope this helps. I do think the screws
need to protrude all the way through the nut plates so a couple of
threads show when installed, same as for a regular nut.
Marty in Brentwood TN
Do not archive
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Dimpling nutplates |
--> RV-List message posted by: Mark Phillips <ripsteel@edge.net>
I ground a flat on the side of a set of dimpling dies almost in to the dimple
recess, then polished it smooth- using your C-frame, carefully line up the
flat side of the dies with the threaded boss on the nutplate and dimple.
Works "most" of the time!
From The PossumWorks in TN
Mark Phillips
Allan.James@hstna.com wrote:
> --> RV-List message posted by: Allan.James@hstna.com
>
> Listers;
>
> I'm getting ready to put the nut plates onto the trim tab
> reinforcement plate, and have a dumb question. I'm assuming the holes on
> the nutplates have to be dimpled for the flush rivets, but the first one I
> did seems to bend the end of the nutplate. Am I right in that these must
> be dimpled. I haven't been able to find any reference to this in the
> archives, nor in the instructions.
>
> Thanks in advance,
> Allan James
> RV7A QB - Elevators
> N322AR
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Dimpling nutplates |
--> RV-List message posted by: "Tim Lewis" <timrv6a@earthlink.net>
Rather than dimpling platenuts, I normally countersunk them.
> >
> > Listers;
> >
> > I'm getting ready to put the nut plates onto the trim tab
> > reinforcement plate, and have a dumb question. I'm assuming the holes on
> > the nutplates have to be dimpled for the flush rivets, but the first one I
> > did seems to bend the end of the nutplate. Am I right in that these must
> > be dimpled. I haven't been able to find any reference to this in the
> > archives, nor in the instructions.
******
Tim Lewis -- HEF (Manassas, VA)
RV-6A N47TD - First Flight 18 Dec 99
http://www.geocities.com/timrv6a
******
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | [ John Starn ] : New Email List Photo Share Available! |
--> RV-List message posted by: Email List Photo Shares <pictures@matronics.com>
A new Email List Photo Share is available:
Poster: John Starn <jhstarn@earthlink.net>
Subject: Rocket Wheel Pant Mod
http://www.matronics.com/photoshare/jhstarn@earthlink.net.07.27.03/index.html
o Main Photo Share Index
http://www.matronics.com/photoshare
o Submitting a Photo Share
If you wish to submit a Photo Share of your own, please include the
following information along with your email message and files:
1) Email List or Lists that they are related to:
2) Your Full Name:
3) Your Email Address:
4) One line Subject description:
5) Multi-line, multi-paragraph description of topic:
6) One-line Description of each photo or file:
Email the information above and your files and photos to:
pictures@matronics.com
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | [ John Starn ] : New Email List Photo Share Available! |
--> RV-List message posted by: Email List Photo Shares <pictures@matronics.com>
A new Email List Photo Share is available:
Poster: John Starn <jhstarn@earthlink.net>
Subject: Cockpit Air Vents
http://www.matronics.com/photoshare/jhstarn@earthlink.net.1.07.27.03/index.html
o Main Photo Share Index
http://www.matronics.com/photoshare
o Submitting a Photo Share
If you wish to submit a Photo Share of your own, please include the
following information along with your email message and files:
1) Email List or Lists that they are related to:
2) Your Full Name:
3) Your Email Address:
4) One line Subject description:
5) Multi-line, multi-paragraph description of topic:
6) One-line Description of each photo or file:
Email the information above and your files and photos to:
pictures@matronics.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|