Today's Message Index:
----------------------
1. 05:18 AM - more Garmin Appolo Manual Downloads (Stewart, Michael (ISS Atlanta))
2. 08:36 AM - Re: FAILED MAIN LANDING GEAR RV-8 (DAVID REEL)
3. 08:43 AM - Re: Lower empennage fairings (Rich Crosley)
4. 09:01 AM - Re: Lower empennage fairings (Mickey Coggins)
5. 09:03 AM - Re: FAILED MAIN LANDING GEAR RV-8 (WFACT01@aol.com)
6. 10:17 AM - Re: FAILED MAIN LANDING GEAR RV-8 (Brian Denk)
7. 11:26 AM - RV-6 sliding canopy weather seal (HCRV6@aol.com)
8. 11:44 AM - Re: RV-6 sliding canopy weather seal (Vanremog@aol.com)
9. 12:20 PM - Re: RV-8 empennage, wings and tools for sale - Milton, Ontario Canada (Are Barstad)
10. 02:56 PM - Another RV finally in the air. (C Ennis)
11. 03:01 PM - Re: RV-6 sliding canopy weather seal (Jim Oke)
12. 03:58 PM - Re: FAILED MAIN LANDING GEAR RV-8 (WFACT01@aol.com)
13. 04:30 PM - RV-4 rear stick (Louis Willig)
14. 04:52 PM - Re: RV-4 rear stick (cgalley)
15. 05:02 PM - baffle drawings for IO-369 (Gert)
16. 05:54 PM - Re: baffle drawings for IO-369 (cgalley)
17. 06:06 PM - Re: RV-4 rear stick (Scott VanArtsdalen)
18. 06:15 PM - Re: RV-6 sliding canopy weather seal (Hopperdhh@aol.com)
19. 06:32 PM - Re: Another RV finally in the air. (Jeff Orear)
20. 06:39 PM - Re: RV-4 Rear Stick (Oldsfolks@aol.com)
21. 07:52 PM - Re: baffle drawings for IO-369 (Gert)
22. 08:16 PM - Re: baffle drawings for IO-369 (cgalley)
23. 08:39 PM - Re: RV-4 rear stick (F44evr@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | more Garmin Appolo Manual Downloads |
--> RV-List message posted by: "Stewart, Michael (ISS Atlanta)" <mstewart@iss.net>
Here are some more(added the first few here below) manuals popular found
by JB. You will notice by looking at the file names and using the
scheme, that you can find just about anything you are looking for. Some
file names are not intuitive like GPS165TSODzusRail_PilotsGuide.pdf. Ill
try and work on getting the entire directory of everything possible. But
for now, this is a really good list. Old and new, popular in junk. Its
in there. STC, pilot Guide, Supplemental Flight Manual, Quick Reference
Guide, Pilots Guide, Installation Manual, Training Syllabus, all kinds
of very useful stuff in there. Just think about how many times you have
wanted a manual and could not find it. Especially installation manuals
which they seem to keep tight reign on. I ran a job from the office to
get all of these, yes every one, so Ill keep them somewhere just in
case they disappear. Another fella did that right before they took the
appolo site down. I got a file from him like
sl40_install_560-0956-03a.pdf. I mean how would you ever figure out that
filename? So I hope to have these stashed just in case GArmin gets hit
by a bus.
http://www.garmin.com/manuals/ these files below. So if you are
looking for a manual, just search this list (ex. Ctl-f 430) and append
the filename to the url above and you will have it.
Enjoy,
Mike Stewart
MX20_InstallationManual.pdf
SL30Nav_Comm_InstallationManual.pdf
SL40Comm_InstallationManual.pdf
SL50_60IFRGPS_InstallationManual.pdf
GX60IFRGPS_COMM_InstallationManual.pdf
SL70Transponder_InstallationManual.pdf
CNX80IntegratedAvionicsSystem_InstallationManual.pdf
GTX327Transponder_InstallationManual.pdf
GTX330Transponder_InstallationManual.pdf
143_InstallationManual.pdf (GPS 400 GNC 420 GNS 430 Series)
CNX80IntegratedAvionicsSystem_PilotsGuide.pdf
CNX80IntegratedAvionicsSystem_QuickReferenceGuide.pdf
CNX80IntegratedAvionicsSystem_CNX80UserNewsletter1.pdf
CNX80IntegratedAvionicsSystem_CNX80UserNewsletter2.pdf
CNX80IntegratedAvionicsSystem_CNX80UserNewsletter3.pdf
CNX80IntegratedAvionicsSystem_CNX80UserNewsletter4.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GNC250XL_PilotsGuide.pdf
156_InstallationManual.pdf
GNC250XL_ApprovedFlightManualSupplement.pdf
GNC300XLTSO_PilotsGuide.pdf
GNC300XLTSO_ApprovedFlightManualSupplement.pdf
GNC300XLTSO_LBAApprovedFlightManualSupplement.pdf
GNC420_PilotsGuide.pdf
140_DisplayInterfacesPilotsGuideAddendum.pdf
141_FDEPilotsGuideAddendum.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GNC420_ApprovedFlightManualSupplement.pdf
GNC420_QuickReferenceGuide.pdf
GNS430_PilotsGuide.pdf
140_DisplayInterfacesPilotsGuideAddendum.pdf
141_FDEPilotsGuideAddendum.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GNS430_ApprovedFlightManualSupplement.pdf
GNS430_QuickReferenceGuide.pdf
GNS430_LBAApprovedFlightManualSupplement.pdf
288_SampleTrainingSyllabus.pdf
GNS530_PilotsGuide.pdf
140_DisplayInterfacesPilotsGuideAddendum.pdf
141_FDEPilotsGuideAddendum.pdf
142_TrafficDisplayPilotsGuideAddendum.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GNS530_ApprovedFlightManualSupplement.PDF
GNS530_QuickReferenceGuide.pdf
GNS530_LBAApprovedFlightManualSupplement.pdf
288_SampleTrainingSyllabus.pdf
GPS150XL_PilotsGuide.pdf
156_InstallationManual.pdf
GPS150XL_ApprovedFlightManualSupplement.pdf
GPS155XLTSO_PilotsGuide.pdf
GPS155XLTSO_ApprovedFlightManualSupplement.pdf
GPS155XLTSO_LBAApprovedFlightManualSupplement.pdf
GPS165TSODzusRail_PilotsGuide.pdf
163_PilotsGuideAddendum.pdf
GPS165TSODzusRail_ApprovedFlightManualSupplement.pdf
GPS400_PilotsGuide.pdf
140_DisplayInterfacesPilotsGuideAddendum.pdf
141_FDEPilotsGuideAddendum.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GPS400_ApprovedFlightManualSupplement.pdf
GPS400_QuickReferenceGuide.pdf
GPS500_PilotsGuide.pdf
140_DisplayInterfacesPilotsGuideAddendum.pdf
141_FDEPilotsGuideAddendum.pdf
142_TrafficDisplayPilotsGuideAddendum.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GPS500_ApprovedFlightManualSupplement.pdf
GPS500_QuickReferenceGuide.pdf
MX20_QuickReferenceGuide.pdf
MX20_STCManual.pdf
MX20_UserGuide.pdf
MX20_MX20AirplaneFlightManualSupplement.pdf
GTX320ATransponder_PilotsGuide.pdf
168_InstallationManual.pdf
GTX327Transponder_PilotsGuide.pdf
147_GarminDisplayInterfacesPilotsGuideAddendum.pdf
GTX330Transponder_PilotsGuide.pdf
SL70Transponder_UserGuide.pdf
SL70Transponder_TSOLetter.pdf
GMA340AudioPanel_PilotsGuide.pdf
SL15MAudioPanel_SL15OperationManual.pdf
SL15MAudioPanel_SL15-CDandCD15OperationManual.pdf
GPS92_PilotsGuide.pdf
GPSIIIPilot_PilotsGuide.pdf
GPSMAP195_PilotsGuide.pdf
GPSMAP196_PilotsGuide.pdf
GPSMAP196_QuickStartGuide.pdf
444_FlightBookQuickStartGuide.pdf
GPSMAP295_PilotsGuide.pdf
GPSMAP295_QuickStartGuide.pdf
GPSMAP296_PilotsGuide.pdf
444_FlightBookQuickStartGuide.pdf
461_OwnersManual.pdf
461_OwnersManual.pdf
NavTalkPilot_PilotsGuide.pdf
NavTalkPilot_InstallationManual_AircraftProvisions_.pdf
NavTalkPilot_InstallationManual_CellularAntenna_.pdf
SL30Nav_Comm_UserGuide.pdf
SL30Nav_Comm_QuickReferenceGuide.pdf
SL30Nav_Comm_JTSOLetter.pdf
SL30Nav_Comm_TSOLetter.pdf
SL40Comm_UserGuide.pdf
SL40Comm_STCKit.pdf
2001_2101C129Series_NMC_2001_2101_OperationManual.pdf
2001_2101C129Series_2001-2101ApproachChecklist.pdf
2001_2101C129Series_2001-2101QuickReferenceGuide.pdf
360GPS_QuickReferenceGuide.pdf
360GPS_STCKit.pdf
360GPS_UserGuide.pdf
360GPS_WaypointManagerforWindowsVer4.pdf
360MAP_QuickReferenceGuide.pdf
360MAP_UserGuide.pdf
600SeriesLORAN_604PilotGuide.pdf
600SeriesLORAN_604QuickReference.pdf
600SeriesLORAN_604QuickReferenceGuide.pdf
600SeriesLORAN_612-614P-614RQuickReference.pdf
600SeriesLORAN_612BOperationHandbook.pdf
600SeriesLORAN_618QuickReferenceGuide.pdf
600SeriesLORAN_618UserGuide.pdf
600SeriesLORAN_602OperationManual.pdf
600SeriesLORAN_602QuickReferenceGuide.pdf
800SeriesLORAN_GPS_800PilotsOperatingManual.pdf
800SeriesLORAN_GPS_800QuickReferenceGuide.pdf
800SeriesLORAN_GPS_820PilotsOperatingManual.pdf
800SeriesLORAN_GPS_820QuickReferenceGuide.pdf
900SeriesGPS_920UserGuide.pdf
900SeriesGPS_920QuickStart.pdf
900SeriesGPS_PrecedusUserGuide.pdf
900SeriesGPS_PrecedusQuickReference.pdf
900SeriesGPS_WaypointManagerforWindowsVer4.pdf
GNC250GPS_COMM_PilotsGuide.pdf
156_InstallationManual.pdf
GNC250GPS_COMM_ApprovedFlightManualSupplement.pdf
GNC300TSOGPS_COMM_PilotsGuide.pdf
GNC300TSOGPS_COMM_InstallationManual.pdf
GNC300TSOGPS_COMM_ApprovedFlightManualSupplement.pdf
GPS100AVD_OwnersManual.pdf
GPS100AVD_InstallationManual.pdf
GPS150_PilotsGuide.pdf
GPS150_InstallationManual.pdf
GPS155TSO_PilotsGuide.pdf
163_PilotsGuideAddendum.pdf
GPS155TSO_InstallationManual.pdf
GPS155TSO_ApprovedFlightManualSupplement.pdf
GPS55AVD_PilotsGuide.pdf
GPS89_PilotsGuide.pdf
GPS90_PilotsGuide.pdf
GPS95AVD_PilotsGuide.pdf
GPS95STD_PilotsGuide.pdf
GPS95XL_PilotsGuide.pdf
GPSCOM190_PilotsGuide.pdf
GTX320Transponder_PilotsGuide.pdf
168_InstallationManual.pdf
GX50IFRGPS_QuickReferenceGuide.pdf
GX50IFRGPS_GX50TrainingPackage.pdf
GX50IFRGPS_UserGuide.pdf
GX55IFRGPS_QuickReference.pdf
GX55IFRGPS_TrainingPackage.pdf
GX55IFRGPS_UserGuide.pdf
GX60IFRGPS_COMM_UserGuide.pdf
GX60IFRGPS_COMM_QuickReferenceGuide.pdf
GX60IFRGPS_COMM_OverflyCancellationLetter.pdf
GX65IFRGPS_COMM_UserGuide.pdf
GX65IFRGPS_COMM_QuickReference.pdf
SL10AudioPanel_UserGuide.pdf
SL50_60IFRGPS_SL50QuickReference.pdf
SL50_60IFRGPS_SL60QuickReference.pdf
SL50_60IFRGPS_UserGuide.pdf
SL50_60IFRGPS_WaypointManagerforWindowsVer4.pdf
SL50_60IFRGPS_TSOC129InstallationFAAApprovalProcedures.pdf
SL50_60IFRGPS_Memo:Cancelsover-flyrequirement.pdf
SL50_60IFRGPS_SystemConfigurationIndex.pdf
SL50_60IFRGPS_SL50_60MasterDrawingList.pdf
SL50_60IFRGPS_SupplementaryAirplaneFlightManual.pdf
82_OwnersManual.pdf
82_OwnersManual.pdf
GPS152_OwnersManual.pdf
GPSMAP162_OwnersManual.pdf
GPSMAP172C_OwnersManual.pdf
73_OwnersManual.pdf
74_QuickStartGuide.pdf
75_GPSMAP182_182C_232OwnersManual.pdf
111_GSD20withGarminChartplotters.pdf
41_OwnersManual.pdf
47_GPSMAP2006_2010_GPS17NInstallationGuide.pdf
111_GSD20withGarminChartplotters.pdf
41_OwnersManual.pdf
47_GPSMAP2006_2010_GPS17NInstallationGuide.pdf
111_GSD20withGarminChartplotters.pdf
75_GPSMAP182_182C_232OwnersManual.pdf
111_GSD20withGarminChartplotters.pdf
GPSMAP3006C_3010C_OwnersManual.pdf
GPSMAP3006C_3010C_InstallationGuide.pdf
GPSMAP168Sounder_OwnersManual.pdf
GPSMAP178CSounder_OwnersManual.pdf
83_GPSMAP188_188C_238OwnersManual.pdf
83_GPSMAP188_188C_238OwnersManual.pdf
FishFinder120_Installation_QuickStartGuide.pdf
FishFinder240_OwnersManual.pdf
437_OwnersManual.pdf
437_OwnersManual.pdf
FishFinder320C_OwnersManual.pdf
FishFinder80_Installation_QuickStartGuide.pdf
GPS12_OwnersManual.pdf
104_GPS12,12XL,48,80Addendum.pdf
GPS12MAP_OwnersManual.pdf
GPS12XL_OwnersManual_SoftwareVersion2.00-3.62_.pdf
GPS12XL_OwnersManual_SoftwareVersion4.0andabove_.pdf
104_GPS12,12XL,48,80Addendum.pdf
GPS72_OwnersManual.pdf
GPS72_QuickStartGuide.pdf
GPS76_OwnersManual.pdf
GPSV_OwnersManual.pdf
GPSMAP175_OwnersManual.pdf
GPSMAP276C_OwnersManual.pdf
GPSMAP60C_OwnersManual.pdf
GPSMAP60CS_OwnersManual.pdf
GPSMAP76_OwnersManual.pdf
GPSMAP76C_OwnersManual.pdf
GPSMAP76CS_OwnersManual.pdf
GPSMAP76S_OwnersManual.pdf
GPSMAP76S_QuickStartGuide.pdf
Rino110_OwnersManual.pdf
Rino110_QuickStartGuide.pdf
Rino120_OwnersManual.pdf
Rino120_QuickStartGuide.pdf
Rino130_OwnersManual.pdf
Rino130_QuickStartGuide.pdf
GBR21_OwnersManual.pdf
GDL30MarineWeatherSatelliteReceiver_OwnersManual.pdf
GMS10NetworkPortExpander_OwnersManual.pdf
47_GPSMAP2006_2010_GPS17NInstallationGuide.pdf
66_GPS16_17NSeriesTechnicalSpecification.pdf
GPS17N_QuickStartGuide.pdf
GSD20_InstallationGuide.pdf
111_GSD20withGarminChartplotters.pdf
Rino110_OwnersManual.pdf
Rino110_QuickStartGuide.pdf
Rino120_OwnersManual.pdf
Rino120_QuickStartGuide.pdf
Rino130_OwnersManual.pdf
Rino130_QuickStartGuide.pdf
VHF720_OwnersManual.pdf
VHF725_OwnersManual.pdf
VHF725_OwnersManual_EuroVersion_.pdf
DGPS53_OwnersManual.pdf
FishFinder100_OwnersManual.pdf
FishFinder100Blue_OwnersManual.pdf
FishFinder160_OwnersManual.pdf
FishFinder160Blue_OwnersManual.pdf
Fishfinder240Blue_OwnersManual.pdf
GBR23_OwnersManual.PDF
GPS100STD_OwnersManual.pdf
GPS120_OwnersManual.pdf
GPS120XL_OwnersManual.pdf
GPS125Sounder_OwnersManual.pdf
GPS12CX_OwnersManual.pdf
GPS45_OwnersManual.pdf
GPS45XL_OwnersManual.pdf
104_GPS12,12XL,48,80Addendum.pdf
GPS48_OwnersManual.pdf
GPS50_OwnersManual.pdf
GPS65_OwnersManual.PDF
GPS75_OwnersManual.pdf
GPSII_OwnersManual.pdf
GPSIIPlus_OwnersManual_SoftwareVersion2.00-2.11_.pdf
GPSIIPlus_OwnersManual_SoftwareVersion3.0andabove_.pdf
GPSIIPlus_QuickStartGuide.pdf
GPSIII_OwnersManual.pdf
GPSIIIPlus_OwnersManual.pdf
GPSIIIPlus_PlusFeaturesAddendum.pdf
GPSCOM170_OwnersManual.pdf
GPSMAP130_OwnersManual.pdf
GPSMAP135Sounder_OwnersManual.pdf
73_OwnersManual.pdf
74_QuickStartGuide.pdf
GPSMAP180_OwnersManual.pdf
GPSMAP185Sounder_OwnersManual.pdf
GPSMAP200_OwnersManual.pdf
130_OwnersManual.pdf
80_OwnersManual.pdf
130_OwnersManual.pdf
80_OwnersManual.pdf
GPSMAP230_OwnersManual.pdf
GPSMAP235Sounder_OwnersManual.pdf
130_OwnersManual.pdf
eTrex_OwnersManual.pdf
eTrexCamo_OwnersManual.pdf
eTrexSummit_OwnersManual.pdf
eTrexVenture_OwnersManual.pdf
Forerunner101_OwnersManual.pdf
Forerunner201_OwnersManual.pdf
Foretrex101_OwnersManual.pdf
Foretrex201_OwnersManual.pdf
Geko101_OwnersManual.pdf
Geko201_OwnersManual.pdf
Geko301_OwnersManual.pdf
GPS12_OwnersManual.pdf
104_GPS12,12XL,48,80Addendum.pdf
GPS12XL_OwnersManual_SoftwareVersion2.00-3.62_.pdf
GPS12XL_OwnersManual_SoftwareVersion4.0andabove_.pdf
104_GPS12,12XL,48,80Addendum.pdf
GPS72_OwnersManual.pdf
GPS72_QuickStartGuide.pdf
GPS76_OwnersManual.pdf
eTrexLegend_OwnersManual.pdf
eTrexLegendC_OwnersManual.pdf
eTrexVenture_OwnersManual.pdf
eTrexVista_OwnersManual.pdf
eTrexVista_Jumpmaster.pdf
eTrexVistaC_OwnersManual.pdf
GPS12MAP_OwnersManual.pdf
GPSV_OwnersManual.pdf
GPSMAP276C_OwnersManual.pdf
GPSMAP60C_OwnersManual.pdf
GPSMAP60CS_OwnersManual.pdf
GPSMAP76_OwnersManual.pdf
GPSMAP76C_OwnersManual.pdf
GPSMAP76CS_OwnersManual.pdf
GPSMAP76S_OwnersManual.pdf
GPSMAP76S_QuickStartGuide.pdf
Rino110_OwnersManual.pdf
Rino110_QuickStartGuide.pdf
Rino120_OwnersManual.pdf
Rino120_QuickStartGuide.pdf
Rino130_OwnersManual.pdf
Rino130_QuickStartGuide.pdf
FishFinder120_Installation_QuickStartGuide.pdf
FishFinder240_OwnersManual.pdf
437_OwnersManual.pdf
437_OwnersManual.pdf
FishFinder320C_OwnersManual.pdf
FishFinder80_Installation_QuickStartGuide.pdf
Rino110_OwnersManual.pdf
Rino110_QuickStartGuide.pdf
Rino120_OwnersManual.pdf
Rino120_QuickStartGuide.pdf
Rino130_OwnersManual.pdf
Rino130_QuickStartGuide.pdf
FishFinder100_OwnersManual.pdf
FishFinder100Blue_OwnersManual.pdf
FishFinder160_OwnersManual.pdf
FishFinder160Blue_OwnersManual.pdf
Fishfinder240Blue_OwnersManual.pdf
GPS12CX_OwnersManual.pdf
GPS38_OwnersManual.pdf
GPS40_OwnersManual.pdf
104_GPS12,12XL,48,80Addendum.pdf
GPS48_OwnersManual.pdf
GPS50_OwnersManual.pdf
GPS75_OwnersManual.pdf
GPSII_OwnersManual.pdf
GPSIIPlus_OwnersManual_SoftwareVersion2.00-2.11_.pdf
GPSIIPlus_OwnersManual_SoftwareVersion3.0andabove_.pdf
GPSIIPlus_QuickStartGuide.pdf
GPSIII_OwnersManual.pdf
GPSIIIPlus_OwnersManual.pdf
GPSIIIPlus_PlusFeaturesAddendum.pdf
GPS12MAP_OwnersManual.pdf
GPSIIIPlus_OwnersManual.pdf
GPSIIIPlus_PlusFeaturesAddendum.pdf
GPSV_OwnersManual.pdf
NavTalkGSM_OwnersManual.pdf
NavTalkGSM_ATCommandInterfaceSupplement.pdf
Quest_OwnersManual.pdf
StreetPilot2610GPS_OwnersManual.pdf
439_OwnersManual.pdf
StreetPilot2650GPS_OwnersManual.pdf
39_OwnersManual.pdf
StreetPilotGPS_OwnersManual.pdf
StreetPilotGPS_AtlanticUsersManual.pdf
StreetPilotGPSColorMap_Ownersmanual.pdf
StreetPilotGPSColorMap_AtlanticOwnersManual.pdf
StreetPilotIIIGPS_OwnersManual.pdf
StreetPilotIIIGPS_QuickStartGuide.pdf
45_USBDataCardProgrammer.pdf
cfQue1620_QuickStartGuide.pdf
cfQue1620_ApplicationsGuide.pdf
eMap_OwnersManual.pdf
GPS12MAP_OwnersManual.pdf
GPSIIIPlus_OwnersManual.pdf
GPSIIIPlus_PlusFeaturesAddendum.pdf
GPSV_OwnersManual.pdf
GPSMAP60C_OwnersManual.pdf
GPSMAP60CS_OwnersManual.pdf
iQue3200_OperatingInstructions.pdf
iQue3200_QueApplicationsGuide.pdf
iQue3600_OperatingInstructions.pdf
iQue3600_QueApplicationsGuide.pdf
Rino110_OwnersManual.pdf
Rino110_QuickStartGuide.pdf
Rino120_OwnersManual.pdf
Rino120_QuickStartGuide.pdf
Rino130_OwnersManual.pdf
Rino130_QuickStartGuide.pdf
GPSIII_OwnersManual.pdf
NavTalk_OwnersManual.pdf
45_USBDataCardProgrammer.pdf
MapSource_BlueChartUsersGuide.pdf
MapSource_MapSourceUsersGuide.pdf
66_GPS16_17NSeriesTechnicalSpecification.pdf
68_QuickStartGuide.pdf
66_GPS16_17NSeriesTechnicalSpecification.pdf
68_QuickStartGuide.pdf
47_GPSMAP2006_2010_GPS17NInstallationGuide.pdf
66_GPS16_17NSeriesTechnicalSpecification.pdf
GPS17N_QuickStartGuide.pdf
GPS18_TechnicalSpecification.pdf
GPS35LPSeries_TechnicalSpecification.pdf
GPS35LPSeries_GPS35USBQuickStartGuide.pdf
GPS35LPSeries_GPS35PCQuickStartGuide.pdf
GPS36TracPak_TechnicalSpecification.pdf
GPS15_TechnicalSpecification.pdf
237_TechnicalSpecifications.pdf
237_TechnicalSpecifications.pdf
GPS25LPSeries_TechnicalSpecification.pdf
GPS31TracPak_TechnicalSpecification.pdf
GPSGuideforBeginners_Manual.pdf
IntroductiontoGeocaching_Manual.pdf
JeppesenUpdateInstructions_Manual.pdf
LoranTDPositionHandbook_Manual.pdf
PCX5_OwnersManual.pdf
usingaGarminGPSwithPaperLandMaps_Manual.pdf
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: FAILED MAIN LANDING GEAR RV-8 |
--> RV-List message posted by: "DAVID REEL" <dreel@cox.net>
I'm very curious how you discovered the problem without damage as I don't think
surface hardness is something apparent to the eye. How would you suggest the
rest of us go about checking for this problem?
Dave Reel RV8A
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Lower empennage fairings |
--> RV-List message posted by: "Rich Crosley" <dirtrider@qnet.com>
Dudley right that how the seal works. I found that "super glue" works
great for sticking the seal to the metal fairing. Have fun!
Rich Crosley
N948RC, RV-8 ready to paint
Palmdale, CA
Hi Mickey,
On the RV-6/A, the seal/gasket for the lower side of the HS is the
same
shape as the wing fairing seal (it is the same cross-section). The
"slot" fits over the aluminum sheet fairing and the "blade" fits
against
the lower side of the HS with the blade slightly bent against the HS.
Hope this helps.
Richard Dudley
-6A painted and about ready to move to the airport
Mickey Coggins wrote:
>--> RV-List message posted by: Mickey Coggins <mick-matronics@rv8.ch>
>
>I'm looking at the lower empennage fairings, and
>can't quite figure out how the rubber seal goes
>on. Is the rubber seal different for the root
>wing fairings and the empennage fairings? I have
>only one type. The picture in the plans look like
>a "fillet" type rubber seal. Any hints appreciated!
>
>Thanks,
>Mickey
>
>--
>Mickey Coggins
>http://www.rv8.ch/
>#82007 QB Wings/Fuselage
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Lower empennage fairings |
--> RV-List message posted by: Mickey Coggins <mick-matronics@rv8.ch>
Hi Rich,
Glad you mentioned gluing the seal to the fairing. I was
going to ask this about the wing root fairing as well.
Mickey
> Dudley right that how the seal works. I found that "super glue" works
>great for sticking the seal to the metal fairing. Have fun!
Mickey Coggins
http://www.rv8.ch/
#82007 QB Wings/Fuselage
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: FAILED MAIN LANDING GEAR RV-8 |
--> RV-List message posted by: WFACT01@aol.com
dave-you have the whitman round gear in a 8A -not a problem.I bent mine on my
third landing-than started checking why-gear not heat theated-NO AIRFRAME
DAMAGE JUST THE GEAR LEG-TOM
Tom Whelan
Whelan Farms Airport
President EAA Chapter 1097
wfact01@aol.com
249 Hard Hill Road North
PO Box 426
Bethlehem, CT 06751
Tel: 203-266-5300
Fax: 202-266-5140
EAA Technical/Flight Advisor
RV-8 540 LYC (Just Flew, Look Out!)
S-51 Mustang Turbine (Under Construction)
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: FAILED MAIN LANDING GEAR RV-8 |
--> RV-List message posted by: "Brian Denk" <akroguy@hotmail.com>
>I'm very curious how you discovered the problem without damage as I don't
>think surface hardness is something apparent to the eye. How would you
>suggest the rest of us go about checking for this problem?
>
>Dave Reel RV8A
Van's sent out a hardness testing kit way back when this problem was
discovered. I think they eventually got it narrowed down to serial number.
My kit serial number is 80379 and the gear legs are fine. I don't think it
went beyond the first 150 or so kits if that.
Brian Denk
RV8 N94BD
RV10 '51
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RV-6 sliding canopy weather seal |
--> RV-List message posted by: HCRV6@aol.com
What have some of you RV-6/7 folks with sliders used for weather and noise
seal where the roll bar and front slider bar meet? Any and all ideas much
appreciated.
Do not archive
Harry Crosby
Pleasanton, California
RV-6, final details
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-6 sliding canopy weather seal |
--> RV-List message posted by: Vanremog@aol.com
In a message dated 9/19/2004 11:27:15 AM Pacific Daylight Time,
HCRV6@aol.com writes:
What have some of you RV-6/7 folks with sliders used for weather and noise
seal where the roll bar and front slider bar meet? Any and all ideas much
appreciated.
===================================================
Harry-
I used EPDM strip available from most home improvement stores.
GV (RV-6A N1GV O-360-A1A C/S, flying 719 hrs)
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RE: RV-8 empennage, wings and tools for sale - Milton, Ontario |
Canada
--> RV-List message posted by: "Are Barstad" <are_barstad@norlogic.com>
Wings and empennage sold this morning.
Tools are still left.
You will get everything included in Avery's complete RV builders toolkit
(including rivet gun, drill, etc.) plus more and lots of clecos. Note: does
not include 90 deg angle drill extension.
New price of toolkit $2200US plus you will probably get an extra $500-1000
worth of tools.
** $1100US ($1450 cdn) takes it all.
Does not include these tools:
13" drill press - 250-3100 rpm - $90cdn
5 hp/20g Air compressor - $300cdn
Band saw (small - $40 takes it)
bench grinder with scotchbrite wheel - $25cdn
bench belt sander - $25cdn
brand new certified torque wrench 20-150 ft.in 1/4" drive from Cleaveland
tools: $75cdn (was $145US)
Parker Rolo Flare tool - $50 cdn
Pick-up only!
You can call me anytime at 416-460-5141
Are
-----Original Message-----
From: Are Barstad [mailto:are_barstad@norlogic.com]
Subject: RV-8 empennage, wings and tools for sale - Milton, Ontario
Canada
All,
I have been offered and have accepted a position in Norway where I will be
working as head of IT for a large oil exploration company. This is a great
opportunity and too good to pass up. They want me over there pronto and so I
will start the job already on October 18th.
My tools will not work there since everything is 220/50hz. It is also very
tough to get a moving company to take the wings and empennage.
Wings are 80% complete but not covered yet. One of the wings have one side
covered. One fuel tank (w/capacitive senders) is done and leak tested. The
other tank is ready for sealing. Landing lights have been fitted in the
leading edge. Empennage is inspected and closed. I have the inspection
papers. Ailerons needs to be built. Flaps needs to be built.
The wings comes in a cradle.
I also have a TSO'd altimeter w/light, VSI w/light and compass w/light. I
have a heated pitot/static tube from Gretch Aero.
Tools:
13" drill press - 250-3100 rpm - $90cdn
5 hp/20g Air compressor - $300cdn
Band saw (small - $40 takes it)
bench grinder with scotchbrite wheel - $25cdn
bench belt sander - $25cdn
Plus: I have absolutely everything else including torque wrench - pneumatic
squeezer, drill press, rivet gun, 37.5 deg. flare tool, compressor etc. I
have several bucking bars (all you need) and all rivet sets you need.
All aircraft specific tools are mostly Avery but some from Cleaveland
Everything must be sold and picked up by October 12 so it will no doubt be a
steal for whoever buys it.
You can e-mail me at are_barstad@manulife.com or call me at 416-460-5141
(cell).
I can sell parts (i.e. tools separately) but all aircraft parts must go as
one lot.
Wings and empennage will go for US$2900 (~$3750 cdn)
I do not have the ability or time to ship items unless it's a larger tool
collection.
Are Barstad
---
---
Message 10
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Another RV finally in the air. |
1.67 SARE_ADULT2 BODY: Contains adult material
--> RV-List message posted by: "C Ennis" <sgtairdog@peoplepc.com>
I am happy to announce the first flight of RV-6A serial # 22558. This morning,
a little after 9AM I flew N60CE for the first time, out of Bluelick airport.5
miles south of Louisville International. Charlie Echo was signed off as airworthy
by the DAR (Pat Patterson) on Saturday the 18th. After waiting all day for
the crosswind to die down, I gave up and returned this morning. After a couple
of more high speed taxi runs I lined up on runway 11 and lifted off in about
300 feet. Forty minutes later I landed on 11 using 1200 feet of Bluelicks 1800
foot grass strip. The flight was uneventful until after touchdown, I must have
had a piece of dirt stuck in the needle valve which caused the carb to overflow
when I throttled back..Which caused a small fireball and a puff of smoke
just as the engine flooded and quit...damn good thing I made a solid landing,
a go around would have been interesting...We pulled the carb and found small
alum shavings in the float bowl..Yeah, we did flush the system, should have done
a better job.
I am delighted with the performance..stalls at 60 indicated,clean around 58 with
full flaps. I flew without main gear fairings or wheel pants, I removed them
during taxi testing and will have to open them up for clearance on grass strips.
Flew hands off at 140 with a touch of right trim. I know I'm rambling and
running on a bit ..11 years and 2200 hours of work came to a climax this morning
and I still haven't got a good grip on what I have accomplished..
Thanks for letting me lurk on the RV List for the last several years..You guys
are a source of priceless information and inspiration.
Charlie Ennis
N60CE
Message 11
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-6 sliding canopy weather seal |
--> RV-List message posted by: Jim Oke <wjoke@shaw.ca>
Harry;
I used some trunk seal rubber strip from a local car restoration shop. Most
of these places sell this stuff by the foot in various cross-sections. I
found some which had a flat side to glue to the windshield bow (I used auto
body filler to get a flat surface) and a cup shaped opposite side that
matched (more or less) the front canopy bow. About 1/2-5/8" thick which
compresses to about 3/8" when the canopy is closed and locked so works well.
Jim Oke
RV-6A C-GKGZ
Wpg, MB
----- Original Message -----
From: <HCRV6@aol.com>
Subject: RV-List: RV-6 sliding canopy weather seal
> --> RV-List message posted by: HCRV6@aol.com
>
> What have some of you RV-6/7 folks with sliders used for weather and noise
> seal where the roll bar and front slider bar meet? Any and all ideas much
> appreciated.
>
> Do not archive
>
> Harry Crosby
> Pleasanton, California
> RV-6, final details
>
>
>
Message 12
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: FAILED MAIN LANDING GEAR RV-8 |
--> RV-List message posted by: WFACT01@aol.com
Brian,
I was serial number 80013, one of the early ones. I questioned Van's at that
time and was told my landing gear was not one of the suspect ones. As for
checking hardness from "heat treating" -- it can only be done with accuracy with
a
Rockwell Hardness Tester. My two gear legs varied from 11C to 48C which could
NEVER have been tested with a homemade punch kit. I have put this information
on the RV-List to serve as a warning to other builders that they should err
on the side of caution. If the gear does bend, you could wipe out your entire
aircraft, in addition to sustaining bodily injury. A good gear is normally in a
spring bent stage with the aircraft weight on it. The problem related to
hardness is that it lacks its spring back memory. I have never seen any of this
written up in the RViator in any detail, including suspected serial numbers. We
have a complete machine shop and sheet metal shop (including English Wheels
and Pullmax Formers, along with much other equipment) on location here. We have
been doing this type of work for over 40 years. And, sadly, this got by us
on my latest airplane. Do what you want with this information.
Regards,
Tom
Tom Whelan
Whelan Farms Airport
President EAA Chapter 1097
wfact01@aol.com
249 Hard Hill Road North
PO Box 426
Bethlehem, CT 06751
Tel: 203-266-5300
Fax: 202-266-5140
EAA Technical/Flight Advisor
RV-8 540 LYC (Just Flew, Look Out!)
S-51 Mustang Turbine (Under Construction)
Message 13
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV-List message posted by: Louis Willig <larywil@comcast.net>
Hi gang,
Does anyone have a rear stick to replace the one I lost in a hangar
fire? If not, does Van sell a pre-fab rear control stick. I can drill and
cut. But I don't know if I can bend a 1" steel tube very well.
Louis
-
Louis I Willig
1640 Oakwood Dr.
Penn Valley, PA 19072
610 668-4964
RV-4, N180PF
190HP IO-360, C/S prop
Message 14
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-4 rear stick |
--> RV-List message posted by: "cgalley" <cgalley@qcbc.org>
Find an electrician. He will be able to bend it.
----- Original Message -----
From: "Louis Willig" <larywil@comcast.net>
Subject: RV-List: RV-4 rear stick
> --> RV-List message posted by: Louis Willig <larywil@comcast.net>
>
> Hi gang,
>
> Does anyone have a rear stick to replace the one I lost in a hangar
> fire? If not, does Van sell a pre-fab rear control stick. I can drill and
> cut. But I don't know if I can bend a 1" steel tube very well.
>
> Louis
>
>
> -
> Louis I Willig
> 1640 Oakwood Dr.
> Penn Valley, PA 19072
> 610 668-4964
> RV-4, N180PF
> 190HP IO-360, C/S prop
>
>
Message 15
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
rv-list <rv-list@matronics.com>
| Subject: | baffle drawings for IO-369 |
--> RV-List message posted by: Gert <gert.v@sbcglobal.net>
Hi Folks
does anybody have a set of drawings for the baffles for an IO360 200 hp??
Thanks
gert
--
is subject to a download and archival fee in the amount of $500
Message 16
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: baffle drawings for IO-369 |
--> RV-List message posted by: "cgalley" <cgalley@qcbc.org>
You are willing to pay $500 to download the baffle plans from my archive?
<GRIN>
----- Original Message -----
From: "Gert" <gert.v@sbcglobal.net>
Subject: RV-List: baffle drawings for IO-369
> --> RV-List message posted by: Gert <gert.v@sbcglobal.net>
>
> Hi Folks
>
> does anybody have a set of drawings for the baffles for an IO360 200 hp??
>
> Thanks
>
> gert
> --
> is subject to a download and archival fee in the amount of $500
>
>
Message 17
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV-List message posted by: "Scott VanArtsdalen" <svanarts@yahoo.com>
I'm pretty sure you can buy a rear stick from them. I didn't modify my
rear stick at all. Just put it in as it came from Van's.
--
Scott VanArtsdalen
RV-4 N311SV
4-ever!
-----Original Message-----
From: owner-rv-list-server@matronics.com
[mailto:owner-rv-list-server@matronics.com] On Behalf Of Louis Willig
Subject: RV-List: RV-4 rear stick
--> RV-List message posted by: Louis Willig <larywil@comcast.net>
Hi gang,
Does anyone have a rear stick to replace the one I lost in a hangar
fire? If not, does Van sell a pre-fab rear control stick. I can drill
and
cut. But I don't know if I can bend a 1" steel tube very well.
Louis
-
Louis I Willig
1640 Oakwood Dr.
Penn Valley, PA 19072
610 668-4964
RV-4, N180PF
190HP IO-360, C/S prop
==
==
==
==
Message 18
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-6 sliding canopy weather seal |
--> RV-List message posted by: Hopperdhh@aol.com
In a message dated 9/19/04 1:44:47 PM US Eastern Standard Time,
Vanremog@aol.com writes:
> Harry-
>
> I used EPDM strip available from most home improvement stores.
>
> GV (RV-6A N1GV O-360-A1A C/S, flying 719 hrs)
>
>
>
What is EPDM?
Dan Hopper
RV-7A N766DH
Flying about 48 hours now since July 7.
Message 19
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Another RV finally in the air. |
--> RV-List message posted by: "Jeff Orear" <jorear@new.rr.com>
Way to go Charlie!
You have me beat for perseverance. I am rounding the corner for home with
my 6A after 7+ years of construction. First flight planned for spring 2005.
You are proof positive that if you stick to it, you *will* end up with an
airplane sooner or later.
Best regards and keep that grin on your face!
Do Not Archive
Jeff Orear
RV6A N782P (reserved)
firewall forward and finishing up behind the panel stuff
Peshtigo, WI
----- Original Message -----
From: "C Ennis" <sgtairdog@peoplepc.com>
Subject: RV-List: Another RV finally in the air.
> --> RV-List message posted by: "C Ennis" <sgtairdog@peoplepc.com>
>
> I am happy to announce the first flight of RV-6A serial # 22558. This
> morning, a little after 9AM I flew N60CE for the first time, out of
> Bluelick airport.5 miles south of Louisville International. Charlie Echo
> was signed off as airworthy by the DAR (Pat Patterson) on Saturday the
> 18th. After waiting all day for the crosswind to die down, I gave up and
> returned this morning. After a couple of more high speed taxi runs I lined
> up on runway 11 and lifted off in about 300 feet. Forty minutes later I
> landed on 11 using 1200 feet of Bluelicks 1800 foot grass strip. The
> flight was uneventful until after touchdown, I must have had a piece of
> dirt stuck in the needle valve which caused the carb to overflow when I
> throttled back..Which caused a small fireball and a puff of smoke just as
> the engine flooded and quit...damn good thing I made a solid landing, a go
> around would have been interesting...We pulled the carb and found small
> alum shavings in the float bowl..Yeah, we did flush !
> the system, should have done a better job.
> I am delighted with the performance..stalls at 60 indicated,clean around
> 58 with full flaps. I flew without main gear fairings or wheel pants, I
> removed them during taxi testing and will have to open them up for
> clearance on grass strips. Flew hands off at 140 with a touch of right
> trim. I know I'm rambling and running on a bit ..11 years and 2200 hours
> of work came to a climax this morning and I still haven't got a good grip
> on what I have accomplished..
> Thanks for letting me lurk on the RV List for the last several years..You
> guys are a source of priceless information and inspiration.
> Charlie Ennis
> N60CE
>
>
>
Message 20
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-4 Rear Stick |
--> RV-List message posted by: Oldsfolks@aol.com
I think you will find that Van's has ALL the parts for RV aircraft. Use your
phone or email !!
Bob Olds RV-4 , N1191X
A&P , EAA Tech. Counselor
Charleston,Arkansas
Real Aviators Fly Taildraggers
Message 21
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: baffle drawings for IO-369 |
--> RV-List message posted by: Gert <gert.v@sbcglobal.net>
I will personally *NOT* drag any broken airplanes from Northpoint all
the way to classic/antique/contempory anymore in my green machine/
gatorette (poor excuse for a green machine), that should be worth the
500 smacko's ;-)
Then again, if you wait till 2005, I will come and suck up personally to
ya.............scary, I know.............but I'll bring beer......
Gert
cgalley wrote:
> --> RV-List message posted by: "cgalley" <cgalley@qcbc.org>
>
> You are willing to pay $500 to download the baffle plans from my archive?
> <GRIN>
>
>
> ----- Original Message -----
> From: "Gert" <gert.v@sbcglobal.net>
> To: <RV-8@yahoogroups.com>; "rv-list" <rv-list@matronics.com>
> Subject: RV-List: baffle drawings for IO-369
>
>
>
>>--> RV-List message posted by: Gert <gert.v@sbcglobal.net>
>>
>>Hi Folks
>>
>>does anybody have a set of drawings for the baffles for an IO360 200 hp??
>>
>>Thanks
>>
>>gert
>>--
>>is subject to a download and archival fee in the amount of $500
>>
>>
>
>
>
>
>
>
>
--
is subject to a download and archival fee in the amount of $500
Message 22
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: baffle drawings for IO-369 |
--> RV-List message posted by: "cgalley" <cgalley@qcbc.org>
Unfortunately, It was a joke! I don't have any baffling.
----- Original Message -----
From: "Gert" <gert.v@sbcglobal.net>
Subject: Re: RV-List: baffle drawings for IO-369
> --> RV-List message posted by: Gert <gert.v@sbcglobal.net>
>
> I will personally *NOT* drag any broken airplanes from Northpoint all
> the way to classic/antique/contempory anymore in my green machine/
> gatorette (poor excuse for a green machine), that should be worth the
> 500 smacko's ;-)
>
> Then again, if you wait till 2005, I will come and suck up personally to
> ya.............scary, I know.............but I'll bring beer......
>
>
> Gert
>
> cgalley wrote:
> > --> RV-List message posted by: "cgalley" <cgalley@qcbc.org>
> >
> > You are willing to pay $500 to download the baffle plans from my
archive?
> > <GRIN>
> >
> >
> > ----- Original Message -----
> > From: "Gert" <gert.v@sbcglobal.net>
> > To: <RV-8@yahoogroups.com>; "rv-list" <rv-list@matronics.com>
> > Subject: RV-List: baffle drawings for IO-369
> >
> >
> >
> >>--> RV-List message posted by: Gert <gert.v@sbcglobal.net>
> >>
> >>Hi Folks
> >>
> >>does anybody have a set of drawings for the baffles for an IO360 200
hp??
> >>
> >>Thanks
> >>
> >>gert
> >>--
> >>is subject to a download and archival fee in the amount of $500
> >>
> >>
> >
> >
> >
> >
> >
> >
> >
>
> --
> is subject to a download and archival fee in the amount of $500
>
>
Message 23
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-4 rear stick |
--> RV-List message posted by: F44evr@aol.com
I think I have a rear stick you can have. I bought my RV-6 kit from a
builder. One of the sticks was totally different from the other. I had to order
the right stick assembly from Van's, they told me that the stick I had was
for an RV4. Email me off list and I'll send you a picture of what I have.
It's yours if it's what you need.
Do Not Archive
Dave
RV6 fuselage
Drill, deburr, dimple, repeat often
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|