---------------------------------------------------------- RV-List Digest Archive --- Total Messages Posted Mon 11/22/04: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:42 AM - The LOC... (Matt Dralle) 2. 07:12 AM - Re: Using Sikaflex for Canopy Installation (JEllis9847@aol.com) 3. 08:46 AM - Re: Re: Using Sikaflex for Canopy Installation (Mickey Coggins) 4. 09:09 AM - Re: High Fuel Pressure (Chris Good) 5. 10:34 AM - Re: Torquing pipe thread elbows for fuel line (HCRV6@aol.com) 6. 11:29 AM - Using Sikaflex to Install Canopy (JEllis9847@aol.com) 7. 06:27 PM - New Dynon Software (Jeff Point) 8. 09:00 PM - QB fuselage and wing (David Alderman) 9. 09:53 PM - Re: QB fuselage and wing (James E. Clark) ________________________________ Message 1 _____________________________________ Time: 02:42:30 AM PST US From: Matt Dralle Subject: RV-List: The LOC... --> RV-List message posted by: Matt Dralle Hi Listers, The List of Contributors (LOC) is just around the corner! On December 1st I post a list of everyone that so generously made a Contribution to support the Lists. Its sort of my way of publicly thanking everyone that took a minute to show their appreciation for the Lists. Won't you take a moment and assure that your name is on that List of Contributors? As a number of people have pointed out, the List seems at least, if not a whole lot more, as valuable as a building/flying/recreating tool as a typical your magazine subscription. We won't even talk about a newsstand price... :-) Won't you take minute and assure that your name is on the upcoming LOC? Tell others that you appreciate the Lists. Making a Contribution to support the Lists is fast and easy using your Visa or M/C on the SSL Secure Web Site: http://www.matronics.com/contribution or by popping a personal check in the mail to: Matronics Email Lists c/o Matt Dralle PO Box 347 Livermore CA 94551-0347 I would like to thank everyone that has so generously made a Contribution thus far in this year's List Fund Raiser! Remember that its YOUR support that keeps these Lists going and improving! Don't forget to include a little comment about how the Lists have helped you! I love to feel the love... :-) Best regards, Matt Dralle Email List Administrator Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551 925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email http://www.matronics.com/ WWW | Featuring Products For Aircraft do not archive ________________________________ Message 2 _____________________________________ Time: 07:12:59 AM PST US From: JEllis9847@aol.com Subject: RV-List: Re: Using Sikaflex for Canopy Installation --> RV-List message posted by: JEllis9847@aol.com Hi Mickey, Sorry for the confusion. If you want to apply additional adhesive to metal or Plexiglas anytime after two hours you should reclean the previously primed area with Sika 226 Cleaner and reprime with Sika 209 Primer. The primer is a very thin polyurethane paint that dries very quickly. I found that if you just want to build up additional adhesive on top of existing adhesive you can scuff the old adhesive with Scotchbrite and clean with isopropyl alcohol. Wait 10 minutes and apply the added adhesive. The resulting joint between the old and new adhesive is undetectable. The effects of UV need to be considered. Sika recommends blocking direct sunlight on the adhesive with opaque band much like to see on car windshields (for the same reason). The Sikaflex 295UV is designed specifically to bond with plastic...plus is has the advantage of being sandable and paintable. I not sure that Silpruf has these properties but may work just as well. Hope this helps clear up the confusion. Jim Ellis finishing canopy RV-9A tip up ________________________________ Message 3 _____________________________________ Time: 08:46:29 AM PST US From: Mickey Coggins Subject: Re: RV-List: Re: Using Sikaflex for Canopy Installation --> RV-List message posted by: Mickey Coggins Hi Jim, Thanks for the info. I'm not sure if silpruf is sandable - that's a good consideration. I've ordered some and I'll check it out. Where did you pick up your sikaflex, primer, and cleaner? Thanks, Mickey At 16:55 22-11-04, JEllis9847@aol.com wrote: -----Start of Original Message----- >--> RV-List message posted by: JEllis9847@aol.com > >Hi Mickey, > >Sorry for the confusion. If you want to apply additional adhesive to metal >or Plexiglas anytime after two hours you should reclean the previously primed >area with Sika 226 Cleaner and reprime with Sika 209 Primer. The primer is a >very thin polyurethane paint that dries very quickly. > >I found that if you just want to build up additional adhesive on top of >existing adhesive you can scuff the old adhesive with Scotchbrite and clean with >isopropyl alcohol. Wait 10 minutes and apply the added adhesive. The resulting >joint between the old and new adhesive is undetectable. > >The effects of UV need to be considered. Sika recommends blocking direct >sunlight on the adhesive with opaque band much like to see on car windshields >(for the same reason). > >The Sikaflex 295UV is designed specifically to bond with plastic...plus is >has the advantage of being sandable and paintable. I not sure that Silpruf has >these properties but may work just as well. > >Hope this helps clear up the confusion. > >Jim Ellis >finishing canopy RV-9A tip up -- Mickey Coggins http://www.rv8.ch/ #82007 QB Wings/Fuselage ________________________________ Message 4 _____________________________________ Time: 09:09:01 AM PST US From: "Chris Good" Subject: Re: RV-List: High Fuel Pressure --> RV-List message posted by: "Chris Good" Kosta, I reported high fuel pressure readings a couple of months ago, also typically at idle power. I first checked the breather, as I saw a report that a breather blockage could cause a high fuel pressure reading. Then I checked & cleaned the sensor contacts. No change. Finally I replaced the sensor. This was on a GRT EIS-4000. Readings have been normal for the last couple of weeks. I guess after 4.5 yrs & 800 hrs, the sensor just needed replacing. Regards, Chris Good. ----- Original Message ----- From: "Kosta Lewis" Subject: RV-List: High Fuel Pressure > > --> RV-List message posted by: "Kosta Lewis" > > I have for years been running between 3-5 to 6 pounds of fuel pressure > depending on I don't know what. Lately I have noticed it keeps at the > high end, 5.5 to 6 at cruise, with a slight increase (needle width) with > adding the boost pump. At idle, it inches towards 7 to 8, which is > redline. No change with fuel tank selection, no change in climb power, > take off performance, fuel consumption. No fuel flow meter, so don't > know that. Fuel line to the carburetor is clear; screens are clear; > nothing in the gascolator screen or sump. I would assume if there was a > blockage before or in the fuel pump(s) the pressure would be low. > Nothing blocking the lines from the pumps to the carb. No leaky fuel > lines. Only recent change: fuel selector valve (nylon innards) that now > is very smooth, as opposed to the old one (brass) that had to be lubed > every 10 or so hours. Hmmmmm. Ideas? > > Michael > > > > > > > -- ________________________________ Message 5 _____________________________________ Time: 10:34:32 AM PST US From: HCRV6@aol.com Subject: Re: RV-List: Torquing pipe thread elbows for fuel line --> RV-List message posted by: HCRV6@aol.com George: 1) NEVER adjust a pipe thread fitting by backing it out. 2) ALWAYS use thread sealant on metal pipe threads carrying fuel, oil or hydraulic fluid. The sealant also acts as a lubricant that will generally let you tighten a fitting enough to get it to the correct position. Nylon fittings for air and vacuum lines do not require sealant. Harry Crosby Pleasanton, California RV-6, flying!!! ________________________________ Message 6 _____________________________________ Time: 11:29:02 AM PST US From: JEllis9847@aol.com Subject: RV-List: Using Sikaflex to Install Canopy --> RV-List message posted by: JEllis9847@aol.com Hi Mickey, I purchased the Sikaflex 295UV adhesive, the Sika 226 cleaner, and the Sika 209 primer from Jamestown Distributors. Their phone number is 800 423-0030 (also 401 253-3840) . They are a boat builder supply store located in Rhode Island. I have had good service from them, and they sell this stuff in less than case lots. They also take credit card orders over the phone. They also have a web page www.jamestowndistributors.com Because some of these items are flammable they have to be shipped by ground so it could take a while to receive depending upon where you live. If you get some let me know what you think about it. Jim Ellis finishing canopy RV9-A tip up ________________________________ Message 7 _____________________________________ Time: 06:27:46 PM PST US From: Jeff Point Subject: RV-List: New Dynon Software --> RV-List message posted by: Jeff Point FYI: The much awaited new version of the Dynon D-10 software just showed up on their website: http://www.dynonavionics.com/docs/EFIS_D10_downloads.html Haven't had a chance to fly it yet, but I've heard that it takes care of the "leaning" issue pretty well. Jeff Point RV-6 Milwaukee WI ________________________________ Message 8 _____________________________________ Time: 09:00:06 PM PST US From: "David Alderman" Subject: RV-List: QB fuselage and wing --> RV-List message posted by: "David Alderman" I am a new sub and wannabe RV-9Aer. Trying to calculate avail space, i.e., garage w/loft and small workshop, 12'x16' (plan to extend 4 or 5 ft). Will greatly appreciate stand-alone length of QB fuselage and length, width, thickness of stand-alone QB wing. Thanks. Ken Alderman in Simpsonville, SC. On the road to retirement? Check out MSN Life Events for advice on how to get there! http://lifeevents.msn.com/category.aspx?cid=Retirement ________________________________ Message 9 _____________________________________ Time: 09:53:59 PM PST US From: "James E. Clark" Subject: RE: RV-List: QB fuselage and wing --> RV-List message posted by: "James E. Clark" Ken, If you can make it over to Columbia, SC some time, you can see a finished RV9A and an RV6A "QB" under construction. James 803-238-2113 If it's Saturday around noon, we've headed out for BBQ so come early and join us!! :-) > -----Original Message----- > From: owner-rv-list-server@matronics.com > [mailto:owner-rv-list-server@matronics.com]On Behalf Of David Alderman > Sent: Monday, November 22, 2004 11:58 PM > To: rv-list@matronics.com > Subject: RV-List: QB fuselage and wing > > > --> RV-List message posted by: "David Alderman" > > I am a new sub and wannabe RV-9Aer. Trying to calculate avail > space, i.e., > garage w/loft and small workshop, 12'x16' (plan to extend 4 or 5 > ft). Will > greatly appreciate stand-alone length of QB fuselage and length, width, > thickness of stand-alone QB wing. Thanks. Ken Alderman in > Simpsonville, SC. > > On the road to retirement? Check out MSN Life Events for advice on how to > get there! http://lifeevents.msn.com/category.aspx?cid=Retirement > >