---------------------------------------------------------- RV-List Digest Archive --- Total Messages Posted Wed 03/16/05: 35 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:25 AM - Re: Elevator Movement after trim cable installation (Ed Anderson) 2. 04:32 AM - Re: Wheel Pants (Brian Alley) 3. 04:52 AM - Re: Need known good mag (cgalley) 4. 04:52 AM - Re: AFM Supplement for GPS IFR - Additional Question (Ron Brown) 5. 06:18 AM - Re: First Flight in LAX Basin (BELTEDAIR@aol.com) 6. 09:11 AM - flight recorder (Wheeler North) 7. 09:56 AM - Re: Elevator Movement after trim cable installation (HCRV6@aol.com) 8. 10:33 AM - RV-Wiki (was: Prepping. Priming, Painting, Etc.) (Dwight Frye) 9. 11:22 AM - Re: RV-Wiki (was: Prepping. Priming, Painting, Etc.) (Tedd McHenry) 10. 11:41 AM - Re: RV-Wiki (was: Prepping. Priming, Painting, Etc.) (Mickey Coggins) 11. 11:44 AM - Re: RV-Wiki (was: Prepping. Priming, Painting, Etc.) (Dwight Frye) 12. 12:37 PM - Re: RV-Wiki (was: Prepping. Priming, Painting, Etc.) (John Spicer) 13. 01:00 PM - Re: RV-Wiki (was: Prepping. Priming, Painting, Etc.) (Dwight Frye) 14. 01:01 PM - Drilling EGT probe holes (Jeff Orear) 15. 01:34 PM - Re: RV-Wiki (was: Prepping. Priming, Painting, Etc.) (John Spicer) 16. 01:42 PM - Re: AFM Supplement for GPS IFR - Additional Question (Richard V. Reynolds) 17. 02:03 PM - ACS air vents (Richard Ernst) 18. 02:10 PM - a short visit (Jim Jewell) 19. 03:08 PM - Re: ACS air vents (sportpilot) 20. 03:34 PM - Re: Displaying Airworthiness Cert. (Mike Robertson) 21. 03:45 PM - Re: Drilling EGT probe holes (Dale Mitchell) 22. 03:56 PM - Re: Drilling EGT probe holes (Brian Kraut) 23. 03:56 PM - Re: Drilling EGT probe holes (Jeff Orear) 24. 03:59 PM - Re: Drilling EGT probe holes (Charles Heathco) 25. 04:08 PM - Re: Drilling EGT probe holes (Larry Bowen) 26. 05:53 PM - Re: Displaying Airworthiness Cert. (cgalley) 27. 06:04 PM - FOR SALE: Turn Coordinator (Dan Checkoway) 28. 06:11 PM - Re: Displaying Airworthiness Cert. (linn walters) 29. 06:21 PM - Re: ACS air vents (Bill VonDane) 30. 06:59 PM - Re: Displaying Airworthiness Cert. (cgalley) 31. 07:25 PM - Re: Drilling EGT probe holes (Fiveonepw@aol.com) 32. 07:32 PM - Re: Displaying Airworthiness Cert. (linn walters) 33. 07:48 PM - Re: Drilling EGT probe holes (Jeff Orear) 34. 08:31 PM - Re: FOR SALE: Turn Coordinator (Scott Jackson) 35. 08:58 PM - Re: FOR SALE: Turn Coordinator (Stein Bruch) ________________________________ Message 1 _____________________________________ Time: 04:25:59 AM PST US From: "Ed Anderson" Subject: Re: RV-List: Elevator Movement after trim cable installation --> RV-List message posted by: "Ed Anderson" Jim, I think that is fairly normal. My elevator will move smoothly up and down and gravity will cause it to droop slightly - but its not as light as minus the cable. Ed A RV-6A N494BW Rotary Powered Matthews, NC ----- Original Message ----- From: "Jim Thorne" Subject: RV-List: Elevator Movement after trim cable installation > --> RV-List message posted by: "Jim Thorne" > > I installed my trim cable today. All seems well except that the elevator now does not freely drop to the down position. It will go to the limit smoothly but you can feel the stiffness the cable has added when moving it by hand. You can't feel it through the stick. Seems every airplane I've ever preflight had free movement up and down so I wondering if mine is normal or something needs to be changed. Couldn't find anything in the archives that seemed to relate to this issue. > > Jim Thorne > RV-7A QB > CHD > > ________________________________ Message 2 _____________________________________ Time: 04:32:50 AM PST US From: Brian Alley Subject: Re: RV-List: Wheel Pants --> RV-List message posted by: Brian Alley Mickey, Composites work is like any other task building an airplane. Quality work is base on the time spent seeking perfection. Your .020 gap on your wheel pants is just about right as you will need a small gap to allow for paint. Best wishes. --- Mickey Coggins wrote: BRIAN ALLEY (N320WT) CARBON FIBER COMPOSITES 101 Caroline Circle Hurricane, WV 25526 304-562-6800 home How are you going to win by a nose if you don't stick out your neck? ________________________________ Message 3 _____________________________________ Time: 04:52:11 AM PST US From: "cgalley" Subject: Re: RV-List: Need known good mag --> RV-List message posted by: "cgalley" Remember, Both Bendix and Slick have a 500 hour remove, open and inspect time. Cy Galley - Chair, AirVenture Emergency Aircraft Repair A Service Project of Chapter 75 EAA Safety Programs Editor - TC EAA Sport Pilot ----- Original Message ----- From: "Charlie Kuss" Subject: Re: RV-List: Need known good mag > --> RV-List message posted by: Charlie Kuss > > Charlie > You might want to consider having your magneto(s) overhauled by Howard > Lebersky. He is an old timer, who has been overhauling Mags since they > were > "cutting edge" technology. He's in Okechobee, Florida. He charged my > friend, Eric Hensen, $120 per mag to rebuild. He does excellent work. > Phone > number is > 863-467-6464 > Charlie Kuss > > >>--> RV-List message posted by: "Charles Heathco" >> >>I have deceided to go with one mag and one electronic for now on my RV6a, >>and both my mags are old and fear they are near end of service. I wonder >>if anyone might have a known good mag laying around from an elec >>conversion they want o sell. I now have bendix, could convert if have the >>wiring. my engine is O-320E2A Charlie heathco, reply to mail >> >> > > > ________________________________ Message 4 _____________________________________ Time: 04:52:11 AM PST US From: "Ron Brown" Subject: Re: RV-List: AFM Supplement for GPS IFR - Additional Question --> RV-List message posted by: "Ron Brown" Subject: Re: RV-List: AFM Supplement for GPS IFR - Additional Question --> RV-List message posted by: "tcolson" >What constitutes an FAA approved flight Manual supplement for an IFR GPS in >an experimental? The approved supplement that comes with GPS sets lists the >certified aircraft to which the STC applies. Since it doesn't cover our RVs >do we need to request specific approval from someone within the FAA? Do we >need to make any mods to the supplement provided such as list our RV >aircraft in the supplement? STC's don't apply to experimentals. Just delete the reference to STC's and the aircraft referenced. Also, the FAA doesn't approve flight Manuals or Supplements for Experimentals. You need to verify that your GPS installation performs as required for IFR maneuvers - gives correct lat/lon, data base and waypoints are synchronized to where you are, that contained approaches are consistent with the paper charts, etc. Then make a log book entry attesting to proper performance of the GPS, sign it, date it, and include your repairman's certificate - much like you did when you certified that phase I was completed and that your plane meets requirements for night and IFR flight as required by your operating limitations. ________________________________ Message 5 _____________________________________ Time: 06:18:55 AM PST US From: BELTEDAIR@aol.com Subject: Re: RV-List: First Flight in LAX Basin --> RV-List message posted by: BELTEDAIR@aol.com Listers, has there been denying of first flight at airports in the LAX basin? Has there been talk of having to trailer the plane to specific airports for the flight test program? Las Vegas would like to know Do Not Archive ________________________________ Message 6 _____________________________________ Time: 09:11:07 AM PST US From: Wheeler North Subject: RV-List: flight recorder --> RV-List message posted by: Wheeler North yes, that would be just perfect. w do not archive ________________________________ Message 7 _____________________________________ Time: 09:56:50 AM PST US From: HCRV6@aol.com Subject: Re: RV-List: Elevator Movement after trim cable installation --> RV-List message posted by: HCRV6@aol.com In a message dated 3/16/05 7:11:48 AM Pacific Standard Time, rv7a@cox.net writes: << I installed my trim cable today. All seems well except that the elevator now does not freely drop to the down position. It will go to the limit smoothly but you can feel the stiffness the cable has added when moving it by hand. You can't feel it through the stick. >> Sounds just like mine and others with manual trim that I have noticed. How could it be otherwise when you think about it, the deflection of the trim cable has to add some small degree of "stiffness" to the system? It is not noticeable in flight to me, and FWIW I am very happy with the manual trim. Harry Crosby Pleasanton, California RV-6, flying! ________________________________ Message 8 _____________________________________ Time: 10:33:53 AM PST US From: Dwight Frye Subject: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: Dwight Frye On Tue Mar 15 20:12:32 2005, Charlie England wrote : >Are there any computer gurus on the list that would be willing to set up >a wiki? Would Matt be willing to host one? It's kind of like a dynamic >FAQ file. > >http://www.google.com/search?hl=en&q=wiki&btnG=Google+Search > >http://wiki.org/wiki.cgi?WhatIsWiki > >Once they are set up, anyone given privileges can alter/add/delete any >info at any time. This might sound chaotic, but the concept seems to >work pretty well. Anyone willing to do so can add info in a much more >concise format so we won't need to wade through dozens or hundreds or >even thousands of emails. The thousands of emails on primer could >probably be condensed to a few dozen overall opinions & have all bases >covered without the info being repeated. I hesitate to chime in here ... but I have set up multiple Wikis, and think they are a fantastic way to share group knowledge. You are right that they are like a "dynamic FAQ", but are even more free-form than that .. which brings unique value *if* the Wiki is an active one. If there is enough interest I might be game to set up a Wiki. Might there be real interest in this? Or is it one of those "sounds cool" things that people won't *really* invest time/energy into? My experience has been that if you get past a certain critical mass of activity, the Wiki can have real value. For one (huge) example of what a Wiki-like site can do, take a look at http://www.wikipedia.com ... a dynamic group-effort online encyclopedia. This is an amazing resource on the web, whether *we* decide we want a Wiki .. or not. -- Dwight do not archive ________________________________ Message 9 _____________________________________ Time: 11:22:08 AM PST US From: Tedd McHenry Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: Tedd McHenry > --> RV-List message posted by: Dwight Frye > --snip-- > Might there be real interest in this? Or is it one of those "sounds cool" > things that people won't *really* invest time/energy into? My experience > has been that if you get past a certain critical mass of activity, the > Wiki can have real value. Dwight: I agree that a wiki is a good way to do it, and I know of some experienced builders (and experts in related fields) who have indicated a willingness to participate in such a project. I have been approached by them before but, not having any experience with setting up a wiki myself, I haven't pursued it. I'd really like to see this go ahead, though, and I would be happy to help if I can. I would also be willing to host the wiki, if that helps. Tedd McHenry Surrey, BC, Canada On Wed, 16 Mar 2005, Dwight Frye wrote: > --> RV-List message posted by: Dwight Frye > > On Tue Mar 15 20:12:32 2005, Charlie England wrote : > >Are there any computer gurus on the list that would be willing to set up > >a wiki? Would Matt be willing to host one? It's kind of like a dynamic > >FAQ file. > > > >http://www.google.com/search?hl=en&q=wiki&btnG=Google+Search > > > >http://wiki.org/wiki.cgi?WhatIsWiki > > > >Once they are set up, anyone given privileges can alter/add/delete any > >info at any time. This might sound chaotic, but the concept seems to > >work pretty well. Anyone willing to do so can add info in a much more > >concise format so we won't need to wade through dozens or hundreds or > >even thousands of emails. The thousands of emails on primer could > >probably be condensed to a few dozen overall opinions & have all bases > >covered without the info being repeated. > > I hesitate to chime in here ... but I have set up multiple Wikis, and > think they are a fantastic way to share group knowledge. You are right > that they are like a "dynamic FAQ", but are even more free-form than > that .. which brings unique value *if* the Wiki is an active one. If > there is enough interest I might be game to set up a Wiki. > > Might there be real interest in this? Or is it one of those "sounds cool" > things that people won't *really* invest time/energy into? My experience > has been that if you get past a certain critical mass of activity, the > Wiki can have real value. > > For one (huge) example of what a Wiki-like site can do, take a look at > http://www.wikipedia.com ... a dynamic group-effort online encyclopedia. > This is an amazing resource on the web, whether *we* decide we want a > Wiki .. or not. > > -- Dwight > > do not archive > > ________________________________ Message 10 ____________________________________ Time: 11:41:39 AM PST US From: Mickey Coggins Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: Mickey Coggins I think it is a great idea, and would add a lot of value to the RV community. I would be happy to contribute where I can. Mickey >>Are there any computer gurus on the list that would be willing to set up >>a wiki? Would Matt be willing to host one? It's kind of like a dynamic >>FAQ file. >> ... > Might there be real interest in this? Or is it one of those "sounds cool" > things that people won't *really* invest time/energy into? My experience > has been that if you get past a certain critical mass of activity, the > Wiki can have real value. ... -- Mickey Coggins http://www.rv8.ch/ #82007 Wiring ________________________________ Message 11 ____________________________________ Time: 11:44:04 AM PST US From: Dwight Frye Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: Dwight Frye On Wed Mar 16 14:20:14 2005, Tedd McHenry wrote : [ ... snip ... ] >I agree that a wiki is a good way to do it, and I know of some experienced >builders (and experts in related fields) who have indicated a willingness to >participate in such a project. I have been approached by them before but, not >having any experience with setting up a wiki myself, I haven't pursued it. I'd >really like to see this go ahead, though, and I would be happy to help if I >can. I would also be willing to host the wiki, if that helps. Tedd, I think having experienced builders (and other experts) willing to join in and participate is _precicely_ the critical factor that has to be taken into consideration. Without knowledgable input the site would be worthless. If you have folks who have expressed interest, then I'm game to (can I be saying this? don't I have enough to do already?) set things up. I'd offer to provide some content ... but ... I'm still learning, and do not feel like much of a "teacher" yet. Maybe with time and experience I can have something to contribute. :) But I can do "geek stuff", and to that end can contribute. I think hosting isn't the big limitation. Reasonable commercial hosting can be had these days for about $10/month. HOWEVER, the big help that you could contribute is in helping create and organize content. Maybe I should go ahead and snag a domain (rvwiki.org??) and set something up .. and we can use the wiki itself to organize getting the wiki organized. If that makes sense. :) Here is the thing I like about a wiki .. and it is the same thing that is driving WikiPedia. It sounds like chaos having anyone and his brother just putting stuff in willy-nilly. And, in the begining it is chaos to a certain degree. However, over time as more and more people read/use/review the wiki you get errors (and hopefully stupidity, urban legands, and old wives tales) massaged out. In time, the most critical and high-interest items become accurate BECAUSE they are critical and high-interest. Or that is the theory. Seems to be working for WikiPedia so far. Does this make sense? Should we take this discussion off-list so we don't bore all the folks who don't want to hear geek-planning-talk? -- Dwight do not archive ________________________________ Message 12 ____________________________________ Time: 12:37:18 PM PST US From: "John Spicer" Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: "John Spicer" If you guys are serious about setting up a wiki I could potentially host it on the existing www.rivetbangers.com server/site. I think it would fold in well with the current support info, document share, etc that is currently in use. Is there any interest in that? -- John S. www.rivetbangers.com - Building more than just RV's www.spikesplace.org/cgi-php/serendipity - Builder's log ----- Original Message ----- From: "Dwight Frye" Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) > --> RV-List message posted by: Dwight Frye > > On Wed Mar 16 14:20:14 2005, Tedd McHenry wrote : > [ ... snip ... ] > >I agree that a wiki is a good way to do it, and I know of some experienced > >builders (and experts in related fields) who have indicated a willingness to > >participate in such a project. I have been approached by them before but, not > >having any experience with setting up a wiki myself, I haven't pursued it. I'd > >really like to see this go ahead, though, and I would be happy to help if I > >can. I would also be willing to host the wiki, if that helps. > > Tedd, > > I think having experienced builders (and other experts) willing to join in > and participate is _precicely_ the critical factor that has to be taken into > consideration. Without knowledgable input the site would be worthless. If > you have folks who have expressed interest, then I'm game to (can I be saying > this? don't I have enough to do already?) set things up. > > I'd offer to provide some content ... but ... I'm still learning, and do > not feel like much of a "teacher" yet. Maybe with time and experience I can > have something to contribute. :) But I can do "geek stuff", and to that > end can contribute. > > I think hosting isn't the big limitation. Reasonable commercial hosting can > be had these days for about $10/month. HOWEVER, the big help that you could > contribute is in helping create and organize content. Maybe I should go ahead > and snag a domain (rvwiki.org??) and set something up .. and we can use the > wiki itself to organize getting the wiki organized. If that makes sense. :) > > Here is the thing I like about a wiki .. and it is the same thing that is > driving WikiPedia. It sounds like chaos having anyone and his brother just > putting stuff in willy-nilly. And, in the begining it is chaos to a certain > degree. However, over time as more and more people read/use/review the wiki > you get errors (and hopefully stupidity, urban legands, and old wives tales) > massaged out. In time, the most critical and high-interest items become > accurate BECAUSE they are critical and high-interest. Or that is the theory. > Seems to be working for WikiPedia so far. > > Does this make sense? Should we take this discussion off-list so we don't > bore all the folks who don't want to hear geek-planning-talk? > > -- Dwight > > do not archive > > ________________________________ Message 13 ____________________________________ Time: 01:00:55 PM PST US From: Dwight Frye Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: Dwight Frye On Wed Mar 16 15:31:35 2005, John Spicer wrote : >If you guys are serious about setting up a wiki I could potentially host it on >the existing www.rivetbangers.com server/site. I think it would fold in well >with the current support info, document share, etc that is currently in use. Is >there any interest in that? There might well be a good fit here. A lot would depend upon available resources on the host site. Ideally it would be a Linux based system with support for PHP and MySQL. Can you shoot me (off-list, so we don't bore the good folks here with geek-details) information about the host environment? Even if we don't co-host the services I think there is a lot of synergy and linking between the two could well make a lot of sense. Lets keep this possibility in mind as we figure out what we want to do. -- Dwight ________________________________ Message 14 ____________________________________ Time: 01:01:49 PM PST US From: "Jeff Orear" Subject: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Jeff Orear" List: This is going to expose how lazy I have gotten, but here goes. I need to drill the holes for my EGT probes and I have already installed and torqued down my exhaust system. Do you think it is a no-no to drill the holes with the exhaust on the engine? Two things come to mind....First I will leave some burs on the inside of the pipe and second, chips will fall into the exhaust. The probe being secured by a hose clamp on the outside of the exhaust will make the burs less of a factor. The fact that all the chips will fall down into the depths of the exhaust and eventually be blown out on first startup makes me feel a little more comfortable there. So do I go ahead and drill or bite the bullet and take the exhaust off?? Regards, Jeff Orear RV6A N782P finishing up engine stuff Peshtigo, WI ________________________________ Message 15 ____________________________________ Time: 01:34:22 PM PST US From: "John Spicer" Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) --> RV-List message posted by: "John Spicer" Emailing you off list.... ----- Original Message ----- From: "Dwight Frye" Subject: Re: RV-Wiki (was: RV-List: Prepping. Priming, Painting, Etc.) > --> RV-List message posted by: Dwight Frye > > On Wed Mar 16 15:31:35 2005, John Spicer wrote : > >If you guys are serious about setting up a wiki I could potentially host it on > >the existing www.rivetbangers.com server/site. I think it would fold in well > >with the current support info, document share, etc that is currently in use. Is > >there any interest in that? > > There might well be a good fit here. A lot would depend upon available > resources on the host site. Ideally it would be a Linux based system > with support for PHP and MySQL. Can you shoot me (off-list, so we don't > bore the good folks here with geek-details) information about the host > environment? > > Even if we don't co-host the services I think there is a lot of synergy > and linking between the two could well make a lot of sense. Lets keep this > possibility in mind as we figure out what we want to do. > > -- Dwight > > ________________________________ Message 16 ____________________________________ Time: 01:42:32 PM PST US From: "Richard V. Reynolds" Subject: Re: RV-List: AFM Supplement for GPS IFR - Additional Question --> RV-List message posted by: "Richard V. Reynolds" By chance, the Richmond, Virginia FSDO Principal Avionics Inspector was at the airport for lunch today. He said: Experimental Aircraft!! No FAA approved flight Manual supplement for an IFR GPS is required for experiment aircraft. Just state in your certificate that the plane will be operated IFR. You still need the altimeter/transponder inspections. Since it does not cost anything, I have down loaded the "sample" FAA approved flight Manual supplement for the Apollo GX60 and will include it in my AFM. Richard Reynolds tcolson wrote: > --> RV-List message posted by: "tcolson" > > What constitutes an FAA approved flight Manual supplement for an IFR GPS in > an experimental? The approved supplement that comes with GPS sets lists the > certified aircraft to which the STC applies. Since it doesn't cover our RVs > do we need to request specific approval from someone within the FAA? Do we > need to make any mods to the supplement provided such as list our RV > aircraft in the supplement? > > Thanks > Tom Olson > N298TC > ________________________________ Message 17 ____________________________________ Time: 02:03:21 PM PST US From: "Richard Ernst" Subject: RV-List: ACS air vents --> RV-List message posted by: "Richard Ernst" I just bought a pair of ACS swivel air vents from Aircraft Spruce (the kind that cost about $55 each), and am unsure how they will connect to SCAT tubing. I am just working on the canopy and panel on my -6A, so I haven't used any SCAT tubing yet, but it seems to me that I need 3/8" or more of a flange protruding from the back of the vent so I can get the SCAT and a hose clamp firmly seated. The ACS air vent only has a little shoulder around 3/16" long. Am I missing a piece? Neither ACS nor Aircraft Spruce has been of any help. Also, the mounting flange on these vents is curious. There are four countersunk mounting holes on the flange, so it must be designed to be mounted on top of some underlying panel. What's curious is that the back side of the flange, the side that contacts the panel, is chamfered, not the front side that you would see. Again, am I missing something? Rick Richard Ernst RV-6A ________________________________ Message 18 ____________________________________ Time: 02:10:45 PM PST US From: "Jim Jewell" Subject: RV-List: a short visit --> RV-List message posted by: "Jim Jewell" WARNING! I will be travelling to Creston B.C. tomorrow Thuraday the 17th and returning to Kelowna Saturday afternoon. I will be free to tour around the vicinity during that time. Are there any aircraft homebuilders in the surrounding area that would help a roaming stray RV6a builder find kindred souls for an hour or two? I am willing to drive 1,1/2 hour or so from Creston on either side of the border to get my aircraft fix {[;-) Jim in Kelowna DO NOT ARCHIVE ________________________________ Message 19 ____________________________________ Time: 03:08:22 PM PST US From: "sportpilot" Subject: Re: RV-List: ACS air vents --> RV-List message posted by: "sportpilot" you need to look again.. at acs EYEBALL AIRVENT ADAPTER 13-00833 $13.85 this may be too big but I think this is what you need.. its 2" and has more information about it.. ----- Original Message ----- From: "Richard Ernst" Subject: RV-List: ACS air vents > --> RV-List message posted by: "Richard Ernst" > > I just bought a pair of ACS swivel air vents from Aircraft Spruce (the > kind > that cost about $55 each), and am unsure how they will connect to SCAT > tubing. I am just working on the canopy and panel on my -6A, so I haven't > used any SCAT tubing yet, but it seems to me that I need 3/8" or more of a > flange protruding from the back of the vent so I can get the SCAT and a > hose > clamp firmly seated. The ACS air vent only has a little shoulder around > 3/16" long. Am I missing a piece? Neither ACS nor Aircraft Spruce has > been > of any help. > > > Also, the mounting flange on these vents is curious. There are four > countersunk mounting holes on the flange, so it must be designed to be > mounted on top of some underlying panel. What's curious is that the back > side of the flange, the side that contacts the panel, is chamfered, not > the > front side that you would see. Again, am I missing something? > > > Rick > > > Richard Ernst > > RV-6A > > > ________________________________ Message 20 ____________________________________ Time: 03:34:34 PM PST US From: "Mike Robertson" Subject: RE: RV-List: Displaying Airworthiness Cert. --> RV-List message posted by: "Mike Robertson" You may remove the Ops Limits form the pink A/W cert. The A/W cert is the only thing you need to display, although most people stick their registration in the same pouch. The Ops limits and W&B can be put anywhere inside the aircraft. Just remember that they must be on board the aircraft wheneveits operated. Mike Robertson >From: Fiveonepw@aol.com >Reply-To: rv-list@matronics.com >To: rv-list@matronics.com >Subject: RV-List: Displaying Airworthiness Cert. >Date: Mon, 14 Mar 2005 13:44:20 EST > >--> RV-List message posted by: Fiveonepw@aol.com > >Howdy! > >Working on the interior of my -6A and need to find a permanent resting >place >for the pink slip, so I'm looking for some ideas how to handle this so it >looks nice, is relatively out of the way, but still meets FAR >91.203:"...displayed >at the cabin or cockpit entrance so that it is legible to passengers or >crew." Apparently the registration and operating limitations (all 5 >pages), >Program Letter, Phase 1 test area description (copy of sectional) and W&B >must be >aboard, but not in view, but the whole package is stapled to the pink slip, >which has a note on the bottom "SEE ATTACHED OPERATING LIMITATIONS". So >I'm >guessing I can't separate the other stuff from the pink slip and have to >figure out >some way to stuff everything into some kind of nice display case for >attachment in the cockpit somewhere. Could some of y'all let me know how >you did it >(off-list or links to fotos would be great!) > >Also, CAN the op-lims & other stuff be separated from the pink slip so it >can >be "framed" and displayed by itself? The op-lims, W&B & other stuff could >go >in a zip-lock along with the POH (oops- Airplane Flight Manual!) and stuck >in >the glove locker? > >Thanks! > >Mark Phillips N51PW, 155 hours > > ________________________________ Message 21 ____________________________________ Time: 03:45:06 PM PST US From: Dale Mitchell Subject: Re: RV-List: Drilling EGT probe holes --> RV-List message posted by: Dale Mitchell Make sure you don,t put the probes where they will be in the way of the spark plugs. Dale Mitchell RV-8A MN wing. --- Jeff Orear wrote: > --> RV-List message posted by: "Jeff Orear" > > > List: > > This is going to expose how lazy I have gotten, but > here goes. I need to drill the holes for my EGT > probes and I have already installed and torqued down > my exhaust system. > > Do you think it is a no-no to drill the holes with > the exhaust on the engine? Two things come to > mind....First I will leave some burs on the inside > of the pipe and second, chips will fall into the > exhaust. > > The probe being secured by a hose clamp on the > outside of the exhaust will make the burs less of a > factor. The fact that all the chips will fall down > into the depths of the exhaust and eventually be > blown out on first startup makes me feel a little > more comfortable there. > > So do I go ahead and drill or bite the bullet and > take the exhaust off?? > > > Regards, > > Jeff Orear > RV6A N782P > finishing up engine stuff > Peshtigo, WI > > > > Contributions > any other > Forums. > > http://www.matronics.com/subscription > http://www.matronics.com/FAQ/RV-List.htm > http://www.matronics.com/archives > http://www.matronics.com/photoshare > http://www.matronics.com/emaillists > > > > > > ________________________________ Message 22 ____________________________________ Time: 03:56:19 PM PST US From: "Brian Kraut" Subject: RE: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Brian Kraut" I have done it before. Unless your engine is upside down and chips will fall into the engine I don't see a problem. I used a scraper that would get inside the hole for getting the burs off. I was concerned about the thin burr getting red hot, but it would probably just burn off and not be a problem anyway. Brian Kraut Engineering Alternatives, Inc. www.engalt.com -----Original Message----- From: owner-rv-list-server@matronics.com [mailto:owner-rv-list-server@matronics.com]On Behalf Of Jeff Orear Subject: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Jeff Orear" List: This is going to expose how lazy I have gotten, but here goes. I need to drill the holes for my EGT probes and I have already installed and torqued down my exhaust system. Do you think it is a no-no to drill the holes with the exhaust on the engine? Two things come to mind....First I will leave some burs on the inside of the pipe and second, chips will fall into the exhaust. The probe being secured by a hose clamp on the outside of the exhaust will make the burs less of a factor. The fact that all the chips will fall down into the depths of the exhaust and eventually be blown out on first startup makes me feel a little more comfortable there. So do I go ahead and drill or bite the bullet and take the exhaust off?? Regards, Jeff Orear RV6A N782P finishing up engine stuff Peshtigo, WI ________________________________ Message 23 ____________________________________ Time: 03:56:28 PM PST US From: "Jeff Orear" Subject: Re: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Jeff Orear" Thanks Dale. I made sure of that when I located the holes. These probes are from Rocky Mountain Instruments and have a 90 degree bend to them after the probe exits the exhaust pipe. Makes it just alittle easier to avoid things like the plugs. Regards, Jeff Orear RV6A N782P finishing up engine stuff Peshtigo, WI ----- Original Message ----- From: "Dale Mitchell" Subject: Re: RV-List: Drilling EGT probe holes > --> RV-List message posted by: Dale Mitchell > > Make sure you don,t put the probes where they will be > in the way of the spark plugs. > Dale Mitchell RV-8A MN wing. > > --- Jeff Orear wrote: >> --> RV-List message posted by: "Jeff Orear" >> >> >> List: >> >> This is going to expose how lazy I have gotten, but >> here goes. I need to drill the holes for my EGT >> probes and I have already installed and torqued down >> my exhaust system. >> >> Do you think it is a no-no to drill the holes with >> the exhaust on the engine? Two things come to >> mind....First I will leave some burs on the inside >> of the pipe and second, chips will fall into the >> exhaust. >> >> The probe being secured by a hose clamp on the >> outside of the exhaust will make the burs less of a >> factor. The fact that all the chips will fall down >> into the depths of the exhaust and eventually be >> blown out on first startup makes me feel a little >> more comfortable there. >> >> So do I go ahead and drill or bite the bullet and >> take the exhaust off?? >> >> >> Regards, >> >> Jeff Orear >> RV6A N782P >> finishing up engine stuff >> Peshtigo, WI >> >> >> >> Contributions >> any other >> Forums. >> >> http://www.matronics.com/subscription >> http://www.matronics.com/FAQ/RV-List.htm >> http://www.matronics.com/archives >> http://www.matronics.com/photoshare >> http://www.matronics.com/emaillists >> >> >> >> >> >> > > > ________________________________ Message 24 ____________________________________ Time: 03:59:29 PM PST US From: "Charles Heathco" Subject: Re: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Charles Heathco" I havent done them myself, but know that they have been done while exaust in place in most cases.Charlie ----- Original Message ----- From: "Jeff Orear" Subject: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Jeff Orear" List: This is going to expose how lazy I have gotten, but here goes. I need to drill the holes for my EGT probes and I have already installed and torqued down my exhaust system. Do you think it is a no-no to drill the holes with the exhaust on the engine? Two things come to mind....First I will leave some burs on the inside of the pipe and second, chips will fall into the exhaust. The probe being secured by a hose clamp on the outside of the exhaust will make the burs less of a factor. The fact that all the chips will fall down into the depths of the exhaust and eventually be blown out on first startup makes me feel a little more comfortable there. So do I go ahead and drill or bite the bullet and take the exhaust off?? Regards, Jeff Orear RV6A N782P finishing up engine stuff Peshtigo, WI ________________________________ Message 25 ____________________________________ Time: 04:08:46 PM PST US From: "Larry Bowen" Subject: RE: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Larry Bowen" I drilled them in place with no problems so far. - Larry Bowen Larry@BowenAero.com http://BowenAero.com > -----Original Message----- > From: Jeff Orear [mailto:jorear@new.rr.com] > Sent: Wednesday, March 16, 2005 3:59 PM > To: rv-list@matronics.com > Subject: RV-List: Drilling EGT probe holes > > --> RV-List message posted by: "Jeff Orear" > > List: > > This is going to expose how lazy I have gotten, but here > goes. I need to drill the holes for my EGT probes and I have > already installed and torqued down my exhaust system. > > Do you think it is a no-no to drill the holes with the > exhaust on the engine? Two things come to mind....First I > will leave some burs on the inside of the pipe and second, > chips will fall into the exhaust. > > The probe being secured by a hose clamp on the outside of the > exhaust will make the burs less of a factor. The fact that > all the chips will fall down into the depths of the exhaust > and eventually be blown out on first startup makes me feel a > little more comfortable there. > > So do I go ahead and drill or bite the bullet and take the > exhaust off?? > > > Regards, > > Jeff Orear > RV6A N782P > finishing up engine stuff > Peshtigo, WI > > > ========= > Matronics Forums. > ========= > ========= > > > > > > ________________________________ Message 26 ____________________________________ Time: 05:53:57 PM PST US From: "cgalley" Subject: Re: RV-List: Displaying Airworthiness Cert. --> RV-List message posted by: "cgalley" W&B has to be on board during operations? ----- Original Message ----- From: "Mike Robertson" Subject: RE: RV-List: Displaying Airworthiness Cert. > --> RV-List message posted by: "Mike Robertson" > > You may remove the Ops Limits form the pink A/W cert. The A/W cert is the > only thing you need to display, although most people stick their > registration in the same pouch. The Ops limits and W&B can be put > anywhere > inside the aircraft. Just remember that they must be on board the > aircraft > wheneveits operated. > > Mike Robertson > >>From: Fiveonepw@aol.com >>Reply-To: rv-list@matronics.com >>To: rv-list@matronics.com >>Subject: RV-List: Displaying Airworthiness Cert. >>Date: Mon, 14 Mar 2005 13:44:20 EST >> >>--> RV-List message posted by: Fiveonepw@aol.com >> >>Howdy! >> >>Working on the interior of my -6A and need to find a permanent resting >>place >>for the pink slip, so I'm looking for some ideas how to handle this so it >>looks nice, is relatively out of the way, but still meets FAR >>91.203:"...displayed >>at the cabin or cockpit entrance so that it is legible to passengers or >>crew." Apparently the registration and operating limitations (all 5 >>pages), >>Program Letter, Phase 1 test area description (copy of sectional) and W&B >>must be >>aboard, but not in view, but the whole package is stapled to the pink >>slip, >>which has a note on the bottom "SEE ATTACHED OPERATING LIMITATIONS". So >>I'm >>guessing I can't separate the other stuff from the pink slip and have to >>figure out >>some way to stuff everything into some kind of nice display case for >>attachment in the cockpit somewhere. Could some of y'all let me know how >>you did it >>(off-list or links to fotos would be great!) >> >>Also, CAN the op-lims & other stuff be separated from the pink slip so it >>can >>be "framed" and displayed by itself? The op-lims, W&B & other stuff could >>go >>in a zip-lock along with the POH (oops- Airplane Flight Manual!) and stuck >>in >>the glove locker? >> >>Thanks! >> >>Mark Phillips N51PW, 155 hours >> >> > > > ________________________________ Message 27 ____________________________________ Time: 06:04:30 PM PST US From: "Dan Checkoway" Subject: RV-List: FOR SALE: Turn Coordinator --> RV-List message posted by: "Dan Checkoway" FOR SALE: Mid-Continent T100-7 turn coordinator + AMP TC connector Purchased brand new from Chief Aircraft in 2003. Retails for $509 + $19 for the connector. In perfect working order, has worked flawlessly for 400+ hours. Will sell for $375 including the already-wired TC connector. Photo here: http://chiefaircraft.com/Aircraft/FlightInstruments/Images/MDCT_T100-7.jpg Reason for selling: upgrading my Digitrak to a Pictorial Pilot, consolidating the two instruments. )_( Dan RV-7 N714D http://www.rvproject.com ________________________________ Message 28 ____________________________________ Time: 06:11:22 PM PST US From: linn walters Subject: Re: RV-List: Displaying Airworthiness Cert. --> RV-List message posted by: linn walters cgalley wrote: >--> RV-List message posted by: "cgalley" > >W&B has to be on board during operations? > Absolutely. How else will you be able to do the calculations before each flight? You do that each time, don't you? :-P Linn do not archive > >----- Original Message ----- >From: "Mike Robertson" >To: >Subject: RE: RV-List: Displaying Airworthiness Cert. > > > > >>--> RV-List message posted by: "Mike Robertson" >> >>You may remove the Ops Limits form the pink A/W cert. The A/W cert is the >>only thing you need to display, although most people stick their >>registration in the same pouch. The Ops limits and W&B can be put >>anywhere >>inside the aircraft. Just remember that they must be on board the >>aircraft >>wheneveits operated. >> >>Mike Robertson >> >> >> >>>From: Fiveonepw@aol.com >>>Reply-To: rv-list@matronics.com >>>To: rv-list@matronics.com >>>Subject: RV-List: Displaying Airworthiness Cert. >>>Date: Mon, 14 Mar 2005 13:44:20 EST >>> >>>--> RV-List message posted by: Fiveonepw@aol.com >>> >>>Howdy! >>> >>>Working on the interior of my -6A and need to find a permanent resting >>>place >>>for the pink slip, so I'm looking for some ideas how to handle this so it >>>looks nice, is relatively out of the way, but still meets FAR >>>91.203:"...displayed >>>at the cabin or cockpit entrance so that it is legible to passengers or >>>crew." Apparently the registration and operating limitations (all 5 >>>pages), >>>Program Letter, Phase 1 test area description (copy of sectional) and W&B >>>must be >>>aboard, but not in view, but the whole package is stapled to the pink >>>slip, >>>which has a note on the bottom "SEE ATTACHED OPERATING LIMITATIONS". So >>>I'm >>>guessing I can't separate the other stuff from the pink slip and have to >>>figure out >>>some way to stuff everything into some kind of nice display case for >>>attachment in the cockpit somewhere. Could some of y'all let me know how >>>you did it >>>(off-list or links to fotos would be great!) >>> >>>Also, CAN the op-lims & other stuff be separated from the pink slip so it >>>can >>>be "framed" and displayed by itself? The op-lims, W&B & other stuff could >>>go >>>in a zip-lock along with the POH (oops- Airplane Flight Manual!) and stuck >>>in >>>the glove locker? >>> >>>Thanks! >>> >>>Mark Phillips N51PW, 155 hours >>> >>> >>> >>> >> >> >> > > > > No virus found in this outgoing message. Checked by AVG Anti-Virus. ________________________________ Message 29 ____________________________________ Time: 06:21:56 PM PST US From: "Bill VonDane" Subject: Re: RV-List: ACS air vents --> RV-List message posted by: "Bill VonDane" speaking of air vents... I just installed one of my new Experimental Air eyeball vents... Man is this thing nice... It fits a standard 2 1/8 instrument hole, and it fits the standard scat tube... Went for a short flight tonight and no leaks! http://www.experimentalair.com/products.html - scroll down the page a bit... It looks GOOD too... One in, two to go... -Bill ----- Original Message ----- From: "sportpilot" Subject: Re: RV-List: ACS air vents --> RV-List message posted by: "sportpilot" you need to look again.. at acs EYEBALL AIRVENT ADAPTER 13-00833 $13.85 this may be too big but I think this is what you need.. its 2" and has more information about it.. ----- Original Message ----- From: "Richard Ernst" Subject: RV-List: ACS air vents > --> RV-List message posted by: "Richard Ernst" > > I just bought a pair of ACS swivel air vents from Aircraft Spruce (the > kind > that cost about $55 each), and am unsure how they will connect to SCAT > tubing. I am just working on the canopy and panel on my -6A, so I haven't > used any SCAT tubing yet, but it seems to me that I need 3/8" or more of a > flange protruding from the back of the vent so I can get the SCAT and a > hose > clamp firmly seated. The ACS air vent only has a little shoulder around > 3/16" long. Am I missing a piece? Neither ACS nor Aircraft Spruce has > been > of any help. > > > Also, the mounting flange on these vents is curious. There are four > countersunk mounting holes on the flange, so it must be designed to be > mounted on top of some underlying panel. What's curious is that the back > side of the flange, the side that contacts the panel, is chamfered, not > the > front side that you would see. Again, am I missing something? > > > Rick > > > Richard Ernst > > RV-6A > > ________________________________ Message 30 ____________________________________ Time: 06:59:36 PM PST US From: "cgalley" Subject: Re: RV-List: Displaying Airworthiness Cert. --> RV-List message posted by: "cgalley" Many planes stay in balance regardless of the gas and passenger load. What's the point if you can't exceed the gross weight of the plane unless you have a 400 pound passenger? Most pilot/builders have explored the math of Weight and balance long before the first flight and know the passenger/gas limits. They already know how large a person they can take for a ride with full down to empty tanks. ----- Original Message ----- From: "linn walters" Subject: Re: RV-List: Displaying Airworthiness Cert. > --> RV-List message posted by: linn walters > > cgalley wrote: > >>--> RV-List message posted by: "cgalley" >> >>W&B has to be on board during operations? >> > Absolutely. How else will you be able to do the calculations before > each flight? You do that each time, don't you? :-P > Linn > do not archive > >> >>----- Original Message ----- >>From: "Mike Robertson" >>To: >>Subject: RE: RV-List: Displaying Airworthiness Cert. >> >> >> >> >>>--> RV-List message posted by: "Mike Robertson" >>> >>>You may remove the Ops Limits form the pink A/W cert. The A/W cert is >>>the >>>only thing you need to display, although most people stick their >>>registration in the same pouch. The Ops limits and W&B can be put >>>anywhere >>>inside the aircraft. Just remember that they must be on board the >>>aircraft >>>wheneveits operated. >>> >>>Mike Robertson >>> >>> >>> >>>>From: Fiveonepw@aol.com >>>>Reply-To: rv-list@matronics.com >>>>To: rv-list@matronics.com >>>>Subject: RV-List: Displaying Airworthiness Cert. >>>>Date: Mon, 14 Mar 2005 13:44:20 EST >>>> >>>>--> RV-List message posted by: Fiveonepw@aol.com >>>> >>>>Howdy! >>>> >>>>Working on the interior of my -6A and need to find a permanent resting >>>>place >>>>for the pink slip, so I'm looking for some ideas how to handle this so >>>>it >>>>looks nice, is relatively out of the way, but still meets FAR >>>>91.203:"...displayed >>>>at the cabin or cockpit entrance so that it is legible to passengers or >>>>crew." Apparently the registration and operating limitations (all 5 >>>>pages), >>>>Program Letter, Phase 1 test area description (copy of sectional) and >>>>W&B >>>>must be >>>>aboard, but not in view, but the whole package is stapled to the pink >>>>slip, >>>>which has a note on the bottom "SEE ATTACHED OPERATING LIMITATIONS". So >>>>I'm >>>>guessing I can't separate the other stuff from the pink slip and have to >>>>figure out >>>>some way to stuff everything into some kind of nice display case for >>>>attachment in the cockpit somewhere. Could some of y'all let me know >>>>how >>>>you did it >>>>(off-list or links to fotos would be great!) >>>> >>>>Also, CAN the op-lims & other stuff be separated from the pink slip so >>>>it >>>>can >>>>be "framed" and displayed by itself? The op-lims, W&B & other stuff >>>>could >>>>go >>>>in a zip-lock along with the POH (oops- Airplane Flight Manual!) and >>>>stuck >>>>in >>>>the glove locker? >>>> >>>>Thanks! >>>> >>>>Mark Phillips N51PW, 155 hours >>>> >>>> >>>> >>>> >>> >>> >>> >> >> >> >> > > > No virus found in this outgoing message. > Checked by AVG Anti-Virus. > > > ________________________________ Message 31 ____________________________________ Time: 07:25:49 PM PST US From: Fiveonepw@aol.com Subject: Re: RV-List: Drilling EGT probe holes --> RV-List message posted by: Fiveonepw@aol.com In a message dated 03/16/2005 3:03:29 PM Central Standard Time, jorear@new.rr.com writes: So do I go ahead and drill or bite the bullet and take the exhaust off?? >>> Hi Jeff- fer whut its wurth, that's what I did- go ahead and FIRE THAT MAMMY JAMMY UP! (You are using a High Country exhaust, no? If not, all betz are off~ 8-)) From The PossumWorks in TN - Mark Phillips, N51PW & 153 hours, burz looked like anti-missile chaff on fire-up! ________________________________ Message 32 ____________________________________ Time: 07:32:51 PM PST US From: linn walters Subject: Re: RV-List: Displaying Airworthiness Cert. --> RV-List message posted by: linn walters cgalley wrote: >--> RV-List message posted by: "cgalley" > >Many planes stay in balance regardless of the gas and passenger load. What's >the point if you can't exceed the gross weight of the plane unless you have >a 400 pound passenger? Most pilot/builders have explored the math of Weight >and balance long before the first flight and know the passenger/gas limits. >They already know how large a person they can take for a ride with full down >to empty tanks. > That wasn't MY answer. That came from the "we're from the FAA and are here to help you" ramp-check guy. And the only reason I had it in the plane (wasn't there when I bought it!) was because I was, at the time, working on my IR rating. I have no problem with your assessment of the abilities of 99% of the folks that fly regularly. I'll bet that almost 1/2 of those that have been flying for, say 5 years .... will have problems figuring a weight and balance!!! The guy that I get my bi-ennial from loves that question!!! Linn > > >----- Original Message ----- >From: "linn walters" >To: >Subject: Re: RV-List: Displaying Airworthiness Cert. > > > > >>--> RV-List message posted by: linn walters >> >>cgalley wrote: >> >> >> >>>--> RV-List message posted by: "cgalley" >>> >>>W&B has to be on board during operations? >>> >>> >>> >>Absolutely. How else will you be able to do the calculations before >>each flight? You do that each time, don't you? :-P >>Linn >>do not archive >> >> >> >>>----- Original Message ----- >>>From: "Mike Robertson" >>>To: >>>Subject: RE: RV-List: Displaying Airworthiness Cert. >>> >>> >>> >>> >>> >>> >>>>--> RV-List message posted by: "Mike Robertson" >>>> >>>>You may remove the Ops Limits form the pink A/W cert. The A/W cert is >>>>the >>>>only thing you need to display, although most people stick their >>>>registration in the same pouch. The Ops limits and W&B can be put >>>>anywhere >>>>inside the aircraft. Just remember that they must be on board the >>>>aircraft >>>>wheneveits operated. >>>> >>>>Mike Robertson >>>> >>>> >>>> >>>> >>>> >>>>>From: Fiveonepw@aol.com >>>>>Reply-To: rv-list@matronics.com >>>>>To: rv-list@matronics.com >>>>>Subject: RV-List: Displaying Airworthiness Cert. >>>>>Date: Mon, 14 Mar 2005 13:44:20 EST >>>>> >>>>>--> RV-List message posted by: Fiveonepw@aol.com >>>>> >>>>>Howdy! >>>>> >>>>>Working on the interior of my -6A and need to find a permanent resting >>>>>place >>>>>for the pink slip, so I'm looking for some ideas how to handle this so >>>>>it >>>>>looks nice, is relatively out of the way, but still meets FAR >>>>>91.203:"...displayed >>>>>at the cabin or cockpit entrance so that it is legible to passengers or >>>>>crew." Apparently the registration and operating limitations (all 5 >>>>>pages), >>>>>Program Letter, Phase 1 test area description (copy of sectional) and >>>>>W&B >>>>>must be >>>>>aboard, but not in view, but the whole package is stapled to the pink >>>>>slip, >>>>>which has a note on the bottom "SEE ATTACHED OPERATING LIMITATIONS". So >>>>>I'm >>>>>guessing I can't separate the other stuff from the pink slip and have to >>>>>figure out >>>>>some way to stuff everything into some kind of nice display case for >>>>>attachment in the cockpit somewhere. Could some of y'all let me know >>>>>how >>>>>you did it >>>>>(off-list or links to fotos would be great!) >>>>> >>>>>Also, CAN the op-lims & other stuff be separated from the pink slip so >>>>>it >>>>>can >>>>>be "framed" and displayed by itself? The op-lims, W&B & other stuff >>>>>could >>>>>go >>>>>in a zip-lock along with the POH (oops- Airplane Flight Manual!) and >>>>>stuck >>>>>in >>>>>the glove locker? >>>>> >>>>>Thanks! >>>>> >>>>>Mark Phillips N51PW, 155 hours >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>> >>>> >>>> >>> >>> >>> >>> >>No virus found in this outgoing message. >>Checked by AVG Anti-Virus. >> >> >> >> >> > > > > No virus found in this outgoing message. Checked by AVG Anti-Virus. ________________________________ Message 33 ____________________________________ Time: 07:48:06 PM PST US From: "Jeff Orear" Subject: Re: RV-List: Drilling EGT probe holes --> RV-List message posted by: "Jeff Orear" Hiya Mark: Will be lite'n the fires in May. Yup, High Country on board. Went ahead and drilled those suckers. Do Not Archive, Ya'll Regards, Jeff Orear RV6A N782P Finishing engine stuff Peshtigo, WI ----- Original Message ----- From: Subject: Re: RV-List: Drilling EGT probe holes > --> RV-List message posted by: Fiveonepw@aol.com > > In a message dated 03/16/2005 3:03:29 PM Central Standard Time, > jorear@new.rr.com writes: > So do I go ahead and drill or bite the bullet and take the exhaust off?? >>>> > > Hi Jeff- fer whut its wurth, that's what I did- go ahead and FIRE THAT > MAMMY > JAMMY UP! > (You are using a High Country exhaust, no? If not, all betz are off~ > 8-)) > > From The PossumWorks in TN - Mark Phillips, N51PW & 153 hours, burz looked > like anti-missile chaff on fire-up! > > > ________________________________ Message 34 ____________________________________ Time: 08:31:53 PM PST US From: "Scott Jackson" Subject: Re: RV-List: FOR SALE: Turn Coordinator --> RV-List message posted by: "Scott Jackson" I'm tempted, mine is grinding away slowly indicating turns and leaning in level flight like a drunken sailor. But the look I'm trying to hang onto in my panel is the '60's RCAF Tutor, surely the trailing edge of technology by now, so I hope to find another T&B. SCott in VAncouver ----- Original Message ----- From: "Dan Checkoway" Subject: RV-List: FOR SALE: Turn Coordinator > --> RV-List message posted by: "Dan Checkoway" > > FOR SALE: > Mid-Continent T100-7 turn coordinator + AMP TC connector > Purchased brand new from Chief Aircraft in 2003. > Retails for $509 + $19 for the connector. > In perfect working order, has worked flawlessly for 400+ hours. > > Will sell for $375 including the already-wired TC connector. > > Photo here: > http://chiefaircraft.com/Aircraft/FlightInstruments/Images/MDCT_T100-7.jpg > > Reason for selling: upgrading my Digitrak to a Pictorial Pilot, > consolidating the two instruments. > > )_( Dan > RV-7 N714D > http://www.rvproject.com > > > ________________________________ Message 35 ____________________________________ Time: 08:58:28 PM PST US From: "Stein Bruch" Subject: Re: RV-List: FOR SALE: Turn Coordinator --> RV-List message posted by: "Stein Bruch" Resist the urge....buy a new TruTrak Pictorial Turn & Bank. No grinding/spinning/whirring Gyros in there! Plus, it's quiet and looks pretty neat too.... I didn't think they looked that neat until I had one in my hand and played with it in my plane, now I swear by them. No going back to the old spinning gyros for me. My Attitude indicator and DG are almost completely shot (from multiple wifferdills, etc..) and I'm working on pushing them completely over the edge here within the next month so I can get a new Trutrak ADI with both the Horizon and DG in the same unit and throw my vacuum system far, far away! I figure it'll take about 4 more cuban 8's, 2 hammerheads and 3 split-s's to completely finish 'em off! Cheers, Stein do not archive - I don't really know what my post even was about... ---------- Original Message ---------------------------------- From: "Scott Jackson" >--> RV-List message posted by: "Scott Jackson" > >I'm tempted, mine is grinding away slowly indicating turns and leaning in >level flight like a drunken sailor. >But the look I'm trying to hang onto in my panel is the '60's RCAF Tutor, >surely the trailing edge of technology by now, so I hope to find another >T&B. >SCott in VAncouver >----- Original Message ----- >From: "Dan Checkoway" >To: >Subject: RV-List: FOR SALE: Turn Coordinator > > >> --> RV-List message posted by: "Dan Checkoway" >> >> FOR SALE: >> Mid-Continent T100-7 turn coordinator + AMP TC connector >> Purchased brand new from Chief Aircraft in 2003. >> Retails for $509 + $19 for the connector. >> In perfect working order, has worked flawlessly for 400+ hours. >> >> Will sell for $375 including the already-wired TC connector. >> >> Photo here: >> http://chiefaircraft.com/Aircraft/FlightInstruments/Images/MDCT_T100-7.jpg >> >> Reason for selling: upgrading my Digitrak to a Pictorial Pilot, >> consolidating the two instruments. >> >> )_( Dan >> RV-7 N714D >> http://www.rvproject.com >> >> >> > >