Today's Message Index:
----------------------
1. 02:07 AM - Pitot tube covers (John Porter)
2. 04:14 AM - Re: Pitot tube covers (Tim Bryan)
3. 05:11 AM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (Dale Ensing)
4. 05:23 AM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (Ralph E. Capen)
5. 07:06 AM - Re: Safeair1 Pitot/Static plumbing kits ? (Darwin N. Barrie)
6. 07:30 AM - Re: Safeair1 Pitot/Static plumbing kits ? (Gerry Filby)
7. 08:32 AM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (smitty@smittysrv.com)
8. 09:59 AM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (Bob)
9. 10:14 AM - Spurious Floscan pulses (Leland and Anne)
10. 10:14 AM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (Dale Ensing)
11. 10:19 AM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (Gerry Filby)
12. 11:07 AM - Re: What Rod end bearing? (Hopperdhh@aol.com)
13. 08:09 PM - Re: Re: Safeair1 Pitot/Static plumbing kits ? (Tim Bryan)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Pitot tube covers |
Hi,
Does anyone have a line on pitot tube covers that fit a Dynon AOA
pitot? I got one from Spruce but it was way too small.
Thanks,
John
80002
----- Original Message -----
From: Jerry2DT@aol.com
To: rv-list@matronics.com
Sent: Tuesday, December 05, 2006 10:30 AM
Subject: RV-List: Re: Superior Engine Delays
Superior has had one delay after another on their forward facing sump
for the injected engines. They are on the third try and that one was
supposed to have been ready last Sept. Then Oct...Nov...Dec... One thing
I find troubling is that they turned over their response to the Sales
Dept., rather than engineering. Getting info out of them is like pulling
teeth on a stubborn mule. I take note that they have plenty of
engineering staff to develop their 400 HP racing engine, but not to take
care of the cracking sump problem...
Sorry for the vent, but you asked...
Jerry Cochran
In a message dated 12/5/2006 12:00:35 AM Pacific Standard Time,
rv-list@matronics.com writes:
If anyone is experiencing delays from Superior on an O/IO-320, I
would
like to hear from you offline.
Thanks
Daniel Snow
RV-9A, Electrical
Daniel.snow@wancdf.com
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Pitot tube covers |
Great question. I bought one from Sporty to fit the Gretz heated pitot, but
way to small also. It slides on so is useable, but will not go back far
enough to fasten it.
Tim
_____
From: owner-rv-list-server@matronics.com
[mailto:owner-rv-list-server@matronics.com] On Behalf Of John Porter
Sent: Tuesday, December 05, 2006 3:24 PM
Subject: RV-List: Pitot tube covers
Hi,
Does anyone have a line on pitot tube covers that fit a Dynon AOA pitot? I
got one from Spruce but it was way too small.
Thanks,
John
80002
----- Original Message -----
From: Jerry2DT@aol.com
Sent: Tuesday, December 05, 2006 10:30 AM
Subject: RV-List: Re: Superior Engine Delays
Superior has had one delay after another on their forward facing sump for
the injected engines. They are on the third try and that one was supposed to
have been ready last Sept. Then Oct...Nov...Dec... One thing I find
troubling is that they turned over their response to the Sales Dept., rather
than engineering. Getting info out of them is like pulling teeth on a
stubborn mule. I take note that they have plenty of engineering staff to
develop their 400 HP racing engine, but not to take care of the cracking
sump problem...
Sorry for the vent, but you asked...
Jerry Cochran
In a message dated 12/5/2006 12:00:35 AM Pacific Standard Time,
rv-list@matronics.com writes:
If anyone is experiencing delays from Superior on an O/IO-320, I would
like to hear from you offline.
Thanks
Daniel Snow
RV-9A, Electrical
Daniel.snow@wancdf.com
href="http://www.aeroelectric.com">www.aeroelectric.com
href="http://www.buildersbooks.com">www.buildersbooks.com
href="http://www.kitlog.com">www.kitlog.com
href="http://www.homebuilthelp.com">www.homebuilthelp.com
href="http://www.matronics.com/contribution">http://www.matronics.com/chref
"http://www.matronics.com/Navigator?RV-List">http://www.matronics.com/Naviga
tor?RV-List
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
Would like more info on the Safeair pitot/static line kits. Is there a web
site with info? Who sells it? Anybody have pictures on web site?
Got many hits on search but not the right stuff.
Dale Ensing
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
try www.safeair1.com
It's right on the front page......
-----Original Message-----
>From: Dale Ensing <densing@carolina.rr.com>
>Sent: Dec 6, 2006 8:09 AM
>To: rv-list@matronics.com
>Subject: Re: RV-List: Re: Safeair1 Pitot/Static plumbing kits ?
>
>
>Would like more info on the Safeair pitot/static line kits. Is there a web
>site with info? Who sells it? Anybody have pictures on web site?
>Got many hits on search but not the right stuff.
>
>Dale Ensing
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
What pitot tube are you using?
I had mine done and was experiencing a leak. I'm using the Dynon AOA
style pitot tube. Turned out the AOA hole on Pitot tube wasn't getting
sealed in the process. We took off the inpsection panel, unhooked the
pitot tube and went directly on that line. No leaks anywhere.
I've heard of several others having this same issue with this tube.
Otherwise it would be very difficult to get a leak on these fittings.
DArwin N. Barrie
Chandler AZ
RV7 N717EE
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
I'm also using the Dynon AOA/Pitot. I had the same issue - I
called Dynon - it has a "calibrated internal leak" that means
you can't pressure test the pitot directly - you have
disconnect the line behind it as you indicate below.
g
> What pitot tube are you using?
>
> I had mine done and was experiencing a leak. I'm using the
> Dynon AOA style pitot tube. Turned out the AOA hole on Pitot
> tube wasn't getting sealed in the process. We took off the
> inpsection panel, unhooked the pitot tube and went directly on
> that line. No leaks anywhere.
>
> I've heard of several others having this same issue with this
> tube. Otherwise it would be very difficult to get a leak on
> these fittings.
>
> DArwin N. Barrie
> Chandler AZ
> RV7 N717EE
>
>
--
__g__
==========================================================
Gerry Filby gerf@gerf.com
----------------------------------------------------------
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
It's time for me to think "pitot" since I'm close to that point in my wing
construction. So... is there a problem with the pitot system that Van shows
on the plans? Should I consider something different?
Opinions are appreciated!
Smitty
http://SmittysRV.com
--------------------------------------------------------------------
mail2web - Check your email from the web at
http://mail2web.com/ .
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
>
>It's time for me to think "pitot" since I'm close to that point in my wing
>construction. So... is there a problem with the pitot system that Van shows
>on the plans? Should I consider something different?
>
>Opinions are appreciated!
I used Van's stainless steel pitot and after four years it works great and
it is super simple. But, if you want heat or AOA or a static port on the
pitot you will have to use something else.
Bob
RV6
Message 9
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Spurious Floscan pulses |
The pulses from Van's Facet pump cause my EIS 4000 to read 2-3
gallons/hour high, when on. This is so even though the pump is in the
cockpit with about two feet of aluminum tubing and a gascolator between
the electric pump and the Floscan head. I tried installing a Matronics
spherical pulse-dampener in the line but did not like having all the
extra fittings. Has anybody on this list tried replacing the aluminum
tubing with flexible fuel line to dampen the pulses?
Leland
RV9A in the paint shop
Message 10
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
I have Van's designed pitot system on my VFR 6A and it works fine. Would not
change it.
Dale Ensing
----- Original Message -----
From: <smitty@smittysrv.com>
Sent: Wednesday, December 06, 2006 11:28 AM
Subject: Re: RV-List: Re: Safeair1 Pitot/Static plumbing kits ?
> <smitty@smittysrv.com>
> It's time for me to think "pitot" since I'm close to that point in my wing
> construction. So... is there a problem with the pitot system that Van
> shows
> on the plans? Should I consider something different?
>
> Opinions are appreciated!
>
> Smitty
> http://SmittysRV.com
>
>
> --------------------------------------------------------------------
> mail2web - Check your email from the web at
> http://mail2web.com/ .
>
>
>
Message 11
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
I don't think there's anything wrong with it, I'm sure it works
just fine on the many planes its installed on.
I went with the Safeair1 plumbing system because, IMHO, its far
easier and quicker to install. I think Vans sticks to alum
tubing for the pitot because its cheap ! Vans pitot "mast"
isn't heated and doesn't give you an AOA option, so you're
paying a little extra to get a lot more by going with the Dynon
or Gretz options.
g
>
> <smitty@smittysrv.com>
>
> It's time for me to think "pitot" since I'm close to that point
> in my wing
> construction. So... is there a problem with the pitot system
> that Van shows
> on the plans? Should I consider something different?
>
> Opinions are appreciated!
>
> Smitty
> http://SmittysRV.com
>
>
> --------------------------------------------------------------------
> mail2web - Check your email from the web at
> http://mail2web.com/ .
>
>
>
>
>
>
>
>
--
__g__
==========================================================
Gerry Filby gerf@gerf.com
----------------------------------------------------------
Message 12
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: What Rod end bearing? |
In a message dated 12/5/2006 10:17:25 PM Eastern Standard Time,
larywil@comcast.net writes:
Hi gang,
There is a small creaking coming from the upper rod end bearing
(hinge) of the rudder of my RV-4. I assume that it need replacement,
but cannot find a part number for this item. I did not build the -4
and don't have the parts call-out list. Help!! Thanks in advance
Louis
Try a little LPS-2 (or Lubriplate) on it!
do not archive
Message 13
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Safeair1 Pitot/Static plumbing kits ? |
I used the Gretz because I wanted the heated pitot. I tried to use Van's
static lines and rivets but I made several attempts to get the tubing to
stay on the rivets, but to no avail I gave up and used the SafeAir kit. I
am very happy with the fittings, and the ports. Wish I wouldn't have spent
so much time messing with the tube stuck over a rivet.
On the other hand, others have had good luck with it. Maybe I did it all
wrong and thus my problems.
Tim
RV-6
> -----Original Message-----
> From: owner-rv-list-server@matronics.com [mailto:owner-rv-list-
> server@matronics.com] On Behalf Of smitty@smittysrv.com
> Sent: Wednesday, December 06, 2006 10:29 AM
> To: rv-list@matronics.com
> Subject: Re: RV-List: Re: Safeair1 Pitot/Static plumbing kits ?
>
> <smitty@smittysrv.com>
>
> It's time for me to think "pitot" since I'm close to that point in my wing
> construction. So... is there a problem with the pitot system that Van
> shows
> on the plans? Should I consider something different?
>
> Opinions are appreciated!
>
> Smitty
> http://SmittysRV.com
>
>
> --------------------------------------------------------------------
> mail2web - Check your email from the web at
> http://mail2web.com/ .
>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|