Today's Message Index:
----------------------
1. 09:03 AM - Spinner Template (Valovich, Paul)
2. 09:33 AM - Re: Spinner Template (Dale Ensing)
3. 06:17 PM - Re: Spinner Template (Bill Schlatterer)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Spinner Template |
I have seen numerous references to a constant speed spinner cut-out templat
e - supposedly located somewhere on the web.
I have searched in all the usual places in an attempt to locate it - with z
ero success.
Can anyone provide the link? I have a new Hartzell prop.
The -8A plans provide clear direction for drawing one by hand, but I want a
cross-check on my efforts. Seems to me that random mass distribution error
s introduced during the prop/spinner mounting process should nearly cancel
out or have minimal effect if one is very careful. However, this is one are
a where I want to do everything possible to eliminate vibration.
Paul Valovich
RV-8A N192NM Reserved (again)
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Spinner Template |
Paul,
I have a drawing/tracing of the actual finished cut-outs in my Van's 6A spi
nner for a Hartzell prop. Can
fax to you if you would like.
Dale Ensing
----- Original Message -----
From: Valovich, Paul
To: rv-list@matronics.com
Sent: Friday, January 09, 2009 11:59 AM
Subject: RV-List: Spinner Template
I have seen numerous references to a constant speed spinner cut-out templ
ate - supposedly located somewhere on the web.
I have searched in all the usual places in an attempt to locate it - with
zero success.
Can anyone provide the link? I have a new Hartzell prop.
The -8A plans provide clear direction for drawing one by hand, but I want
a cross-check on my efforts. Seems to me that random mass distribution err
ors introduced during the prop/spinner mounting process should nearly cance
l out or have minimal effect if one is very careful. However, this is one a
rea where I want to do everything possible to eliminate vibration.
Paul Valovich
RV-8A N192NM Reserved (again)
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Spinner Template |
Not sure if this is the one you want but it is for the blended AF Hartzell
on my O-360 A1A. Others available on the Hartzell site.
Hope this helps!
Bill S
7a finishing
_____
From: owner-rv-list-server@matronics.com
[mailto:owner-rv-list-server@matronics.com] On Behalf Of Valovich, Paul
Sent: Friday, January 09, 2009 11:00 AM
Subject: RV-List: Spinner Template
I have seen numerous references to a constant speed spinner cut-out template
- supposedly located somewhere on the web.
I have searched in all the usual places in an attempt to locate it - with
zero success.
Can anyone provide the link? I have a new Hartzell prop.
The -8A plans provide clear direction for drawing one by hand, but I want a
cross-check on my efforts. Seems to me that random mass distribution errors
introduced during the prop/spinner mounting process should nearly cancel out
or have minimal effect if one is very careful. However, this is one area
where I want to do everything possible to eliminate vibration.
Paul Valovich
RV-8A N192NM Reserved (again)
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|